Very very basic - ecumaster det3 in its so called fuel implant (standalone) mode + ford edis6 system for ignition, det3 controls the edis module.

Nice 😊 where do you get spareparts nowadays? 🧐

here and there, on the internet and at the edges of the fields. I also have several spareparts car😊

@@taunusstyle nice! I have also one, TC 71 - 2.3V6, but i need some parts as well.

Yes, air inlet from the back. It was running on home made megasquirt 1

@@madmodsgarage1179 so you use a throttle body? Any more photos or videos please?

@@chrisTiFur76 it was plumbed like a turbo. Air filter - open inlet to supercharger, outlet to intercooler, from intercooler to engine's stock throttle body. And a biiig blow off valve before the throttle :P check facebook.com/madmodsgarage, there is an album with this car. Unfortunetely, this capri doesn't run any more, sold the engine (100% ok), built some other projects. I still have the chassis, but years went by, and it's slowly returning to mother earth ;P

@@madmodsgarage1179 thanks, I’m seriously debating about doing mine found a m90 and also m112 locally

@@chrisTiFur76 the setup was pushing the m62 hard AF. I was overspeeding it pretty badly... going bigger is very good idea, for a 3.5, the m90 should be enough, unless your answer to "how much boost are you going to run?" Is "YES" :P

Yup

Kinda bolt on but not exactly. Right side engine mount (v6) is 100% bolt on, this gives You correct engine position to modify or fabricate left side (stock v6 doesnt fit engine block bolt pattern). 4.0 oil sump needs to be cut and welded to make room for granada subframe. Or you can use 2.9 sump, most bolt holes line up, but some not, and mounting flange is wider in some places, I think its much better to cut and weld 4.0 aluminium sump. Then You will probably get some hood clearance issues with stock intakce manifold. Plastic one is a little bit shorter, but still very close or slightly hitting the hood. Yes, type 9 gearbox and all v6 flywheels is 100% bolt on, but with torque of that engine and granada weight, I doubt it would last long...

@@madmodsgarage1179 How did you fit the gearbox?

​@@ghj1502custom adapters and flywheels. The car used to have mazda rx8 6speed gearbox, now it has a nissan cd009 from a 350z

@@madmodsgarage1179 is this a kit you could possibly sell?

@@madmodsgarage1179 Also, did you put the 422 comp cam in the engine?

Yeah, could be, I don't remember how loud they were in real life, this was couple years ago, not my car. Also, phone mics do this, extremely amplify high pitch noises under the hood/bonnet. Could have been all good in fact but can't tell for sure now. In EFI cars for example, all you hear in the vid is incjectors clicking :)

Mine sounds exactly like that with the tappets adjusted to what the Haynes manual says, Essex V6s don't run right with the tappets too tight it's better to leave them to factory settings or even a bit loose.

my dad is the owner of this car

Po pierwsze nieoplacalne dla jednego nie jest nieoplacalne dla drugiego, a po drugie 2.8 bylo od zawsze w planach, zeby podmienic w przyszlosci za 2.3. I tak bedzie, graty na spokojnie sie zbierają, silnik zacznie byc kiedys budowany, tylko tu nie ma presji czasu, auto caly czas jezdzi i bardzo cieszy wlasciciela w obecnej konfiguracji :)

a fakt ze "nadaje sie" do jazdy na wprost to zasadniczo jak kazdy stary ford bez radykalnej przebudowy zawiasu, co poza tym nie dyskwalifikuje go z sensu posiadanie podniesionej mocy :)

nope :)

The clonk must be the sound of the fuel tank aggressively going empty

its all aluminum motor

hehe no chłostamy jeszcze, pozdro

I do custom fabrication so none of the cars I built had stock exhaust, but go ahead and try it, deleting back muffler will be easier. Just cut it off in a comfortable to work place, start the car. If it sounds rubbish You can always weld it back on

Nie zdziwia mi to że go nie widziałeś

:) stare blachy, auto obecnie smiga sobie w UK, wlasciciel ten sam, zeby nie bylo ;) ale kiedys wroci i beda upgrady :]

0.5m 3" downpipe through the hood

so I guess it's an uppipe lol