Good video bro. I've been to Japan once before but I'm going again in March.
@jeflui17 күн бұрын
@@ToastyZach thanks, I’m going back next month.
@dissitsyaga334Ай бұрын
What is that radio model ? Do u have the fosgate build?
@reallifeengineer72142 ай бұрын
I see you used the RA snorkel to help de-bottleneck potential choke points. (Very clean snorkel by the way. Did you buy it new? That’d be crazy. How much do Mitsubishi dealers charge for that?) Now, one thing you MIGHT want to do, because this is absolutely a known choke point for non-turbo trims: At the front of the snorkel, where the snorkel rests on the radiator top cover trim, That trim has open slits molded-in when manufactured. Those slits’ combined cross section area, is even smaller than the ES snorkel’s inner cross section area. So at WOT, those slits becomes the bottleneck against air flow. Especially now you have gone to RA snorkel, I suggest you to manually cut more slits into that plastic cover/trim. Personally the easiest way I’ve found, is to drill holes that’ll be the two end-stops for each slit. Diameter of the drill bit should be exactly the same as the slit width you want. Then, using Dremel cut disk, cut the edges of each slit until the cut meets the hole. You will want to run your power tools at a slow enough speed so you are cutting and not melting the plastic. If you are melting it, it might appear you’re making faster progress, but the aftermath becomes very difficult to control and quite a mess to clean up.
@jeflui2 ай бұрын
@@reallifeengineer7214 I bought the snorkel brand new from Mitsubishi at the time for just over $54 after shipping & taxes. I rarely drive my lancer hard so I’m not concerned with any bottlenecks with airflow. I can’t remember the last time I drove at WOT.
@B.Assassin4444 ай бұрын
What submodel is your lancer?
@LucianPaine7 ай бұрын
But how did you remove the trim on dashboard left of steeringwheel ?
@efraimsolano76808 ай бұрын
Hi! Sorry I don't understand, where is the ground cable connected? Thanks a lot
@LAgirl414 Жыл бұрын
Does anyone know how to remove the AC control trim at all? I've been looking up how to get to it for years now.
@marciaewell2661 Жыл бұрын
good content, but the loud "music" is an assault on my ears. I had to hover my finger over the mute button, ugh!!!!
@AEKs22 Жыл бұрын
I installed my windoe visors exactly the same as yours and I thought I made a mistake coz I noticed the pictures from ebay. I was planning to reinstall it until I saw this vid😂
@Kg_Sp22 Жыл бұрын
Anyone know the size of wrap sheet this is?
@MNYEPZ873 ай бұрын
6ft 5ft
@andreiyastreb8193 Жыл бұрын
Super 😮👌👍💪
@Walid_UmarRayhan23 Жыл бұрын
Thank bro.. 💪🏼🇲🇾
@rohandemoore5083 Жыл бұрын
Have you ever installed a rear weather shield? And if so what did you use to keep it stuck on. I've tried double sided tape and the heat just makes it come off.
@mathiasmeer6943 Жыл бұрын
Good job 👌🏾
@rodrigoledezma2261 Жыл бұрын
Te amo
@jonwattles61752 жыл бұрын
Aye this is my exact car never seen someone in America with it! I’m sore they are out there though!
@iFocusET2 жыл бұрын
support internet sim card?
@brayanlerdo3692 жыл бұрын
Hey buddy quick question will this be able to fit a 2017 lancer 2.0L ?
@sergiofernandogutierrezmem26462 жыл бұрын
What kind of screen is that you bought? where did you buy it? I need an equal one for my Lancer GTS 2016, could you share the link to buy an equal one
@jeflui2 жыл бұрын
Literally everything I’ve used is always in the descriptions of my videos
@stevenfontanilla96482 жыл бұрын
2021 I tried to order to our local dealership and they said they don't make Ralliart snorkel anymore and after 2 years of looking for a snorkel, I found one used for $10 super steal. i just have a k&n filter and Ralliart snorkel.
@reallifeengineer72142 ай бұрын
Your setup is probably the better way honestly. To-date, I have not seen any manufacturer of cone-shaped filters publish the actual surface area of their filtrate. Surface area = the cross section available for air to flow through the filter. The greater the area, the better. For cone filters to “make sense” vs the generic/OEM filter, cone filter needs greater area. Otherwise, EVEN IF the cone filter did permit more flow, the only way it got that more flow is by having bigger pores that lets through more dirt & contaminant into the engine.
@dredman16282 жыл бұрын
Never saw this filter model intake before, but I like because it is enclosed preventing direct heat from the engine bay reaching the filter. Question - is the heat shield that mounts to the stock airbox metal or plastic
@jeflui2 жыл бұрын
Metal
@reallifeengineer72142 ай бұрын
Metal. That’s how we can hear more sound coming backwards from the engine through the intake pipe. Had it being plastic, that sound would have being muffled just like the factory air box.
@AdrianAntonio2 жыл бұрын
Did u plastidip your grill? I have the 2016 lancer and I can’t find that film that’s compatible with my car on Amazon. If u find a link lemme kno
@backrowcinema2 жыл бұрын
i liked it!
@josuearana87562 жыл бұрын
Do you a pdf of all to unmount all this part of Mitsubishi Lancer
@mattandkatchristie25522 жыл бұрын
Thanks
@sahil35682 жыл бұрын
Hello bro, is your mirror 7 wires or 9 wires? Do you have glass heater in your side mirror?
@VETRAVONDURINN2 жыл бұрын
Does anyone know where online I can order the wrap in this video
@richardjinlopez90932 жыл бұрын
Yow bro where did you buy those visors?
@jeflui2 жыл бұрын
eBay, I link everything in my descriptions
@MegaTeacherg2 жыл бұрын
Great video thank helped lots and saved me cash
@eslachance2 жыл бұрын
Heyyyy that reminds me I also need to put more coolant in the tank because it's low...
@stevonic122 жыл бұрын
I tried lowering the steering wheel and pulling the cluster cover out but it didn't work I want to change the colour of the cluster lights
@ahaad9762 жыл бұрын
Brother I request you to make your interior carbon fibre..wrap it like glowing carbon fibre
@jeflui2 жыл бұрын
Not a fan of carbon fiber look
@onehellspawn2 жыл бұрын
It's been 2 years, and how has that unit been treating you now? Has it been working great still with no issues?
@jeflui2 жыл бұрын
No issues at all. Use it all the time still works as good as it did from day 1. Sound quality could be better tbh but that’s more of just needing better car speakers than factory ones. But no complaints overall.
@onehellspawn2 жыл бұрын
@Jef Lui alright good to know, thanks for the quick reply too!! 😁
@akosbihari55652 жыл бұрын
Never ever gonna buy another chinese product for 100-150$ that failed to boot up after several month.IF YOU CANT AFFORD A GOOD ONE DONT BUY THE CHEAPER ONE TOO,learn from my mistake.COOL VID BRO>
@longbar23442 жыл бұрын
so sticking deflectors on with 3m tape. who the hell needs a guide on doing this pmsl
@friedanal5092 жыл бұрын
The curves were tough for me
@Mcevoy912 жыл бұрын
Just pop out the airbag to reinstall the buttons. Much much easier
@malachiperez31272 жыл бұрын
l
@noheartmadis2 жыл бұрын
Does the cold air intake work on my mitsubishi lancer 2008 1.8l
@reallifeengineer72142 ай бұрын
1.8 L would be a different engine. What was shown in this video works with the 2.0L 4B11, and the 2.4L 4B12. The 1.8L… Honestly if that engine uses the same air intake system as the 4B11 & 4B12, then 1) yes it could use this Takeda intake, but 2) why would you bother, the intake for 2.0L/2.4L is not the bottleneck for a 1.8L engine.
@babukaxxorov3482 жыл бұрын
Thank you for video👍 from Azerbaijan
@Gre3nPp0w3r2 жыл бұрын
this is exactly the video I wanted to see , cuz im doing the same thing to my car
@abbaspourmoghadam38502 жыл бұрын
Does it fit on verada?
@Fizzzy0182 жыл бұрын
Thanks man, extremely helpful
@MDER262 жыл бұрын
Hi, what do you do to fit the clip with the housing? I have that problem
@ericleyva24152 жыл бұрын
I like it but be nice if u had a word for word on how to do it
@weldermen3 жыл бұрын
to make relearn the computer,after plug back the batterie,put the key on 3 minutes without start the car,after 3minute with ALL Accessories OFF,turn off the key for 10 second,and then,start the car with accessories OFF, and DOnt touch the PEDAL of gas, the computer have to relearn the throttle position ,and lot of stuff,so,let it idling for 10 minutes,and let it sit for the next ride,the car will lean how to set the cpu at speed.
@weldermen3 жыл бұрын
you should cleAn your throttle body...on the video i saw, it is dirty a lot in the back..it not help the airflow ;)
@bmxhotsauce3 жыл бұрын
How do you take out the OE mirror ? Or does thing just cover the OE mirror?
@user-oi4pk8fu1n3 жыл бұрын
nice sound...
@LE550N3 жыл бұрын
Did it bent a little in the middle? By the time.
@jeflui3 жыл бұрын
nope mine was fine even through hot summers & cold winters until it flew off on the highway