Yes ! It helped thank you

Thank you for the video - good stuff :) I never had that much luck with the exhaust/manifold gasket material when trying to be precise. So i figured out, that clamping the gasket material between two thinish pieces of wood, and screwing them tightly together, i could use basic tools to get really nice gaskets. I can drill out the holes with regular brad point bits and forstner bits, cut along the outside with bandsaw/jigsaw and creep up on edges with a belt sander and dremel. No burrs, no raised edges, no damage and perfect results, just from a template made from placing painters tape over the surface i needed the gasket for, and making the outline with the side of a pencils lead (or a dirty finger :) )

You’re a life saver!

Sure most will figure it out. To remove black bezel go in your back seat I have 03’ 4 door fold back seats down and you can now access trunk/bed crawl in and there’s 3 middle screws IGNORE THEM there’s 2 small screws on each side of those 3 middle screws. Remove the 2 screws it’s a T30 torx now black bezel will pop off and u can get in/see better.

Is it the same with all trucks?

What fittings did you use driver.

Cert welder u can use lube on wire gun helps quite a bit keeps wore from sticking and they also have a plastic insulated wolf weres out caused henpick on wire guns have keep clean tips to buy lube helps gd luck I just rebuild same deck also on plate fully the hole weres out few thousand s on these mowers u can just use a ring take up.slack I drilled hold out on washers one size over was not problem it was plat up down in plate holding the pully was causing belt come off as well as front rod on front motor puller bad bout leting belt ger lose

Thanks! Nice close up!

I've tried this and can never tin the cable properly.

He’s touching it with his dirty hands it’s going to get infected

My bracket was pulled out of deck. Took an old blade and cut it to fit under the deck and welded on with the hole of old blade lined up with bracket hole. Then got a bolt long enough to extend through bracket to put pulley back on. Very strong and the cheesey bracket doesn't have any pressure on it.

Thank u for the video

Hello, thank you so much for the video. I am having some issues with mine. The heat works fine. Ac is having issues. The second the compressor clutch kicks, the belt stops unit dies. I can't figure what is going on. I will be glad if you can help. Thank you so much

Gun powder and a lighter even though how bad it’ll hurt

for the last two weeks ive been trying to get my apu running I'm getting negative amps and the service tool also says app switch off and hmco open what could cause this ive been trying everything watching this I'm thinking I might have a bare wire on my ac comp would that cause all my problems thanks for any info ..

Just took my tailgate apart thank you for showing exactly what I need to do it’s hard to see in there, I only have one rod to come off the assembly and with your help I’ll be able to fix it thank you

UPDATE: Since I received this knife, I have been using it everyday and I have not even sharpened it at all yet. I have honed it after some rough use but I honestly don't even know why I even did that when the knife was still insanely sharp (force of habit I suppose!) My only problem with Jeo Tec is that they don't make larger knives, like a 9 or 10 inch, so I'm going to have to buy a Becker BK9 since I don't want to lug a machete around in the bush to blaze a trail. Anyway, The more I use this knife, especially with friends around me, tends to build up sentimental value on it. I too, had a knife that was of very sentimental value that I lost, not because it was given to me, but because of the times I've had with it, especially around a good friend who used it multiple times but who died in a drowning accident many years ago. It killed me when I lost it so, I get it. Hopefully you are able to do a lot of cool stuff with your no.37. Please do a follow up video, I would love to see it. Also, you do know you could go to Bucks website and get the 119 in S35VN right? I might decide to get one but what I really need is a bigger knife.

Only video that actually helped me set the valve lash

I got the same motor

Thank for video…. I believe that’s my problem…. You gave really good tips…👍🏾🙏🏾

Great little engine

Thank you very much

And that is why I have 9 fingers

What size are those fittings coming off that primary tank??

Injection injuries are awful. Thank God it wasn't a toxic chemical.

Thanks for the help!

cheers

Wow for a big dude your a big softie I’ve had bigger cuts on my japs eye

You made it sound like your leg meat was hanging lmaoooooo. I was like omgggggg ok he’s gonna show it. Then that thing lmaooooooo. You’ll b iight bro heal up

How can i add Coolant to the apu or does it share from the Engine?

i have the same apu run for 5 to 10 minutes and shut down that connection on the 50 volts fuse look ok the alternator is pushing 13.9 volts, i just did apm with om parts and still doing that all fuses are good fans both working good, you have idea what else could be?

There dasmascus big hunting knifes go for £100.00 & dasmascus tomahawks go for £125.00 or check "impact cutlery"

Thank you , this is a really a blessing . Shalom

Where did you get the springs and retainers

the subaru bois stoked about this one!

Hey, just wondering what was the reason for buying a new heating element if the old one had been working and simply drooped a little low. Couldn’t you have just bent it back up?

Thank you

Thank you I preciate you... Save around 3k

I just got a d2 steel Perkin and have to say they make great knives...their sheaths are another story! Thanks for sharing your blade!

Good day, great video tutorial my friend. Have a question, mine is not blowing cold air, I checked voltage at the compressor connector and got only 7 volts, doesn’t it supposed to get 12? Also check pressure on gas and is ok, any advice will be much appreciated, thanks, blessings.

what sling shot do you have

what size bolt did you use and what length

Nice thanks👍

working on the same briggs 8hp engine,old gasket was shredded in the valves

Thanks for showing nothing.

This reminds me once I was in Maui and I was snorkeling and then a wave swept me into a rock and my knee hit the rock so hard that it literally showed like a small hole all the way to the bone. I still have the scar it looks like I got shot.

yea these things are no joke i wasdetaching the surface cleaner from my pressure washer and the trigger somehow got pulled and it left my pointer finger with a pretty deep and painful cut

I just took some skin off on my right thumb cleaning out the bottom deck of my mower.

Pretty neat.

Grow the fuck up buttercup 🧚‍♀️