In my experience I cracked my front frame horn. I'm sure pretty uncommon but that was the culprit. Welded up and ready to go again
@devonrose8883 жыл бұрын
Lower control arm bushings
@saadabidate57473 жыл бұрын
100 ch ?
@김혜옥-s1z3 жыл бұрын
four stroke ?
@dirkdheuvaert95863 жыл бұрын
Hello sir may i ask , what is the pitch of your prop and do you have a special nosecone on the engine, i self have a hpdi 200 and want to make it faster, and what about a jackplate , regards dirk
@05tacoSPORT3 жыл бұрын
23P Yamaha M prop with the OEM lower unit. Mine ran fastest with the jack plate all the way down.
@cleveland49503 жыл бұрын
Mine was doing the same thing, it turned out to be the alignment bolts on the control arm and the bolts that hold the rack and pinion, I’ve tightened them and the popping noise it’s gone for good 😀
@INTERNA9 Жыл бұрын
You are right
@pablodela15063 жыл бұрын
tengo ese problema en mi 2008 tacomo lift 3in
@norbertobravo17453 жыл бұрын
Is that normal
@yessahblesssah55164 жыл бұрын
I have the same problem on my 2015 Toyota Tacoma a popping noise not sure if it’s the control arms
@carlosjulian54344 жыл бұрын
I have the same problem. Do you find solution
@PACK-ge5gu4 жыл бұрын
Have any issues with motor? Like power head , Trim, ect?
@Nate_HarietteYouTube_Adventure4 жыл бұрын
Don’t put junk on nice vehicles
@DaveRogers5834 жыл бұрын
No on in this comment section knows wtf their talking about. There is no torsion bar on these trucks and on this truck the sway bar has been removed. Check the cv axle where it goes into the differential housing. There's an issue with the needle bearing inside the diff. Ecgs has a remedy.
@curtisswanson75842 жыл бұрын
Dave I have the same exact noise and I replaced the needle bearing with the ECGS clamshell bushings and it did not help at all. Not all sounds come from the same place.
@Z-Ack Жыл бұрын
Mine makes same noise but it doesnt have any cv axles in the front. Is. 2wd..
@sanantonio21075 жыл бұрын
It's the control arm bolt it shifts back and forward I got under the truck and my friend was turning the wheel and saw it
@austinmerritt79035 жыл бұрын
I have the same issue I've replaced everything control arm bushings ball joints tie rod ends removed my sway bar new bearings new cv axles and no change seems to be during steering and going into reverse on mine. But yours seems to do it more often is the uca contacting your spring possibly
@shawnpittman51202 жыл бұрын
This is my problem exactly. Did you ever find out the reason for the pop?
@watchmanexpert Жыл бұрын
Did u found the problem?
@macdaddy16175 жыл бұрын
What was the problem?, ever figured it out?
@05tacoSPORT5 жыл бұрын
I ended up replacing the lower Control arms and all these issues went away
@Alfredo-zb4kk5 жыл бұрын
On my Taco, problem was that the sway bar was rubbing slightly on the shock coils, bought the sway bar relocation kit for $40.00 and that solved my problem. With this video it appears from the viewer angle that the uniball cup on the upper control arm is rubbing with the coil although I could be wrong. It looks like you removed the sway bar so that can't be the problem.
@scottshirai60645 жыл бұрын
Did you source the problem yet? If not does the popping occur when you step on the brake pedal?
@caseynewland26145 жыл бұрын
I have this issue as well
@mynig4life3 жыл бұрын
Thats what mines do
@meexiong15415 жыл бұрын
Axle
@caseynewland26145 жыл бұрын
Nah I have the same problem on my prerunner
@taavaj6 жыл бұрын
Put sway bar relocate on problem should solve lol, I just did my and it gone.
@babycurt036 жыл бұрын
Please sell your truck now. you have no idea what you're talking about there is no sway bar clearly he took it off there is no sway bar In any part of this video so what are you talking about.
@reeffreak6 жыл бұрын
sinking?
@05tacoSPORT6 жыл бұрын
Rally Tasker always sinking. But it’s a ranger so it should be ok right?
@dannyrocks7776 жыл бұрын
Sounds like a bad CV.
@jeremysierra47636 жыл бұрын
What was the issue ?
@atcdan1338 жыл бұрын
Any damage?
@05tacoSPORT8 жыл бұрын
atcdan133 none whatsoever
@jdsparks1008 жыл бұрын
Pretty smokey, but I don't care. I'm one of those unique types that enjoys the shit out of scrubbing down my firearms!
@ruyguy88888 жыл бұрын
do you find those 29s rub anywhere during the suspension flex or full lock turning?
@05tacoSPORT8 жыл бұрын
They rub in the rear a little. Bike is a stock height and tires at 6psi or so
@ruyguy88888 жыл бұрын
It seems a bit odd that the rear of the machine seem to be the more common rub points rather than the front. Good to know. thanks for the response.
@javieralmaraz81878 жыл бұрын
what were you using for bait?
@05tacoSPORT8 жыл бұрын
Gizzard Shad
@tylerhallman17068 жыл бұрын
*check sway bar links is what i meant
@austinmerritt79035 жыл бұрын
What sway bar
@tylerhallman17068 жыл бұрын
Your uca isn't hitting your spring. That white bit that looks like a chip is the sticker pealed off (I have the same OME on my truck) check control arms. Your truck doesn't have torsion bars. Torsion bars were replaced as soon as the tacoma came out. Toyota pickups had torsion bars.
@05tacoSPORT8 жыл бұрын
its sold
@ryanlock11058 жыл бұрын
still have it
@justfixitnow778 жыл бұрын
Instead of beads why not use 50/50 antifreeze and water?
@brandonhickman73948 жыл бұрын
+justfixitnow77 way too much wieght imagine getting into mud with them you would be done
@lukeskywalker16749 жыл бұрын
Look at your coil over! There is clearly wear / rubbing mark on it where the paint is chipped off near the top, considereing the spring looks pretty damn clean and the fact your a arm is super close i would suggest that they are rubbing together. The spring def rotated to allowing us too see the rubbing mark. Change out your a arm or get a narrower spring.
@porthos69149 жыл бұрын
tighten sway bar bolts they are loose
@05tacoSPORT9 жыл бұрын
Nashville TN. Ready to wheel when you are. We are all within 5 hours
@evolnivlek9 жыл бұрын
how far from Columbus are you guys. I would like to wheel. FJ40 linked on won tons.
@08customstar10 жыл бұрын
Video credits.
@05tacoSPORT10 жыл бұрын
Pitbull Rockers sound good trying to find traction 😃
@Bassinwithjesse10 жыл бұрын
Punching the trigger
@Bassinwithjesse10 жыл бұрын
Punching the trigger
@05tacoSPORT10 жыл бұрын
I am. Bad habit.
@delandgixxer75010 жыл бұрын
Nice Trails, I'm going have to go up to TN. some day, Nice Vid!!!
@05tacoSPORT10 жыл бұрын
Well I replaced everything just about trying to get rid of the noise. Coilovers along with new upper and lower control arms.
@carcharias10 жыл бұрын
Did the noise go away?
@carcharias10 жыл бұрын
Just found the knock on my own vehicle - lca bushing going bad and knocking against metal. Thanks for the video! It actually helped me.
@ryanrabe53137 жыл бұрын
carcharias u
@porthos69145 жыл бұрын
LOL, So what ended up fixing your issue>? I guess all the above.
@carcharias10 жыл бұрын
I have this exact noise and have been trying for 3 months to figure it out!! What's the answer? We don't have torsion bars (2011 Tacoma), and I haven't seen any of my own videos where the uca hits the coil. Have you found the source of this noise???
@luissalgado14336 жыл бұрын
Hello, I have the same problem, how have you solved it?
@02diablon10 жыл бұрын
salfidel is right its ur control arms hitting the coil spring.
@jasojeep11 жыл бұрын
Any update on the noise? I have a similar sound on my 09.
@08customstar11 жыл бұрын
That's an awesome looking 80! Needs a front locker though.
@05tacoSPORT11 жыл бұрын
No. I have 10oz in each 35. Some speeds are fine. Some shake like hell
@jdmsi9211 жыл бұрын
Do they work all the time? I'm running 8oz in my 35s and they still shake.
@badranger200411 жыл бұрын
My 06 does this after installing biltstine 5100s but only over bumps
@jayflores84336 жыл бұрын
badranger2004 did you figure out the problem? I have the same problem. With bilstein 5100 coilovers
@jdjdgf50013 жыл бұрын
@@jayflores8433 2 years later, u guys find problem i have old man emu 888 and same noise over bumbs
@joeylazio59893 жыл бұрын
Just installed 2.5” dobinson lift kit and my front driver side is CLUNKY as all get out when driving especially bad over bumps. Any solutions?
@jdjdgf50013 жыл бұрын
@@joeylazio5989 I'm not sure but I had some weight in the back and I dint hear any noise. But I heard it again after I unloaded. So I'm thinking since we upgrade shocks, we just might have to light of a truck and to strong suspensions. Just a thought
@jdjdgf50013 жыл бұрын
@@joeylazio5989 also I took it mudding kinda hard and the noise seems to be gone now. Mabey u just have to break it in lol
@ugaparker11 жыл бұрын
hey man great vid.... Subscribe and check out some of my vids !