Can you link me the attachment for the rotary conversion? I can’t find that one only the DA.
@DetailedImage24 күн бұрын
You will want the iBrid Nano Rotary Function Unit www.detailedimage.com/Rupes-M62/iBrid-Nano-Rotary-Function-Unit-P1287/
@radekliko52629 күн бұрын
Thanks for the content. Should you make the choice again. Would you think that 1x Multimatch 8 connect would be a better set up than 2x Multimatch 3 connect or even 1x Multimatch 3 connect for the car detailing. It looks that the both lights have power, so it may be down to the modularity each can offer.
@DetailedImage26 күн бұрын
It all depends on what other lights you have on hand. If you are leaning on your Scangrip more, the 8 would be my choice. Unless you want to have two different sources of light, then the 2x 3s or 2x 8s are great. The Connect series is great as well if you have the batteries on hand, it helps get you into these lights at a lower price point.
@fredyruiz8854Ай бұрын
Thanks for the information very useful.
@peterjones1354Ай бұрын
Surely the wheel has to come off before you start this job. What about the back of the wheel and spokes?
@DetailedImageАй бұрын
You can use skinny brushes like the EZ Detail Mini to reach most of the back areas, however, for a complete clean removing wheels like this is suggested.
@ILLSMOKQ-xs6qsАй бұрын
That’s a fiesta but still cool I own a 16 focus st 👍🏻
@wilmermendoza7752Ай бұрын
What’s the size for buying the pads for the 15mm polisher
@DetailedImageАй бұрын
@wilmermendoza7752 It all depends on the pad manufacturer and the backing plate size. If you are using a 5" backing plate, make sure the pads have a back that is the same size, or slightly larger. For example, the Lake Country flat foam pads are 5.5", or you can reach for something like the Rupes pads, where the 6" pads have a 6" face and are beveled with a 5" back. Hope that helps!
@wilmermendoza7752Ай бұрын
@@DetailedImage thanks for the help
@KevW81Ай бұрын
You were this close 🤏 to saying Maguires 🤣
@gilsoto87512 ай бұрын
Does the 1st application rag need to be damp. Or dry?
@DetailedImage2 ай бұрын
You want your towels to be clean and dry.
@mygt8a4re2 ай бұрын
Can anyone tell me if this product is usef as an "addition" to a wash detergent, or is it just used on its own? I've been using a dye free detergent with vinegar for years with great results. Have been curious to try this.
@DetailedImage2 ай бұрын
Rags to Riches is not an additive, it is a microfiber detergent designed to be used on its own. Check out the video for not only a review, but how to use the detergent as well. If you would prefer to read about the product, the review can be found here (www.detailedimage.com/Ask-a-Pro/product-review-ps-rags-to-riches-premium-microfiber-detergent/)
@mygt8a4re2 ай бұрын
@DetailedImage thanks for the response. I've heard some people say they use it in conjunction with their free & clear detergent, on several occasions actually, so I wanted to be sure. Thank you!
@davidtn2272 ай бұрын
I know this is an old video but does this brush fit by area with the brake pad and rim? I always use my ex detail brush but I’m always getting the old dirty water splashing me when I pull the brush out. Or is there a brush you would recommend for that area that won’t splash me with the water.
@DetailedImage2 ай бұрын
It can fit in that area, depending on the wheel design. It does well in most tight areas, but the EZ Detail Brush does fit into tighter areas for sure.
@markperez61952 ай бұрын
Can we add C2V3 on a surface that has CSL with EXO as a topper already?
@DetailedImage2 ай бұрын
You can! C2 works great as a topper to an existing coating layer, or as a stand alone protection layer for a few months.
@stevel38813 ай бұрын
Is it bendable?
@DetailedImage3 ай бұрын
There is a flexible core, so it does bend or flex during use.
@stevel38813 ай бұрын
@@DetailedImage can it be bent at a 90° angle to get behind wheel spokes
@DetailedImage3 ай бұрын
It is very flexible and can bend a good amount, however, it cannot be bent and held at a 90 degree angle.
@2twofive3414 ай бұрын
can you layer exo v5
@DetailedImage4 ай бұрын
EXOv5 is a single layer application, but you certainly can add a second layer if desired.
@SoleMax234 ай бұрын
A signature series polisher 🥴🤷🏽♂️.
@eprohoda4 ай бұрын
How are you?~well unboxing!
@zoa900x4 ай бұрын
Can I use a polish n wax after? Or before?
@DetailedImage4 ай бұрын
You will want to inspect the paint and correct with only the highest correction needed. Meaning, you only want to use a heavy compound like the 400 if you have imperfections that need it. If you do use the 400, you would follow up with a lighter pad and polish combo to remove compounding haze and finish the paint down to perfection.
@spc1485 ай бұрын
Metrovac hands down. I use to use my leaf blower
@rpurdum6 ай бұрын
Great review - you definitely prepared me for what is needed prior to purchase. Thanks!
@millerdetailing41767 ай бұрын
Great video and definitely a great coating and topper.
@DetailedImage7 ай бұрын
Happy to hear that you enjoyed the video and Aquatek!
@UpbeatSagar17 ай бұрын
Hi I’ve a deep scratches on my car which is of the colour Nardo Grey. I’m confused whether this can remove the scratches or make it less visible or is it only for the minor colour corrections? Help is highly appreciated. Thanks
@DetailedImage7 ай бұрын
Thank you for reaching out! Please contact us here (www.detailedimage.com/Contact/) and a rep can help asap!
@Semaj.182727 ай бұрын
Do I need the next step 2400 ? Or can I just skip to the. Polish 3500 this is for quick sell of csr
@DetailedImage7 ай бұрын
It all depends on your paint and the condition after compounding. With that said, 3500 is a big jump from the 400, so I would recommend a light correction option like the 3000 or 2500. Just perform a test spot and inspect the results to find what combo will work best for your specific situation.
@12MRJERSEY7 ай бұрын
But is it gear driven like the flex?
@DetailedImage7 ай бұрын
This unit is not a gear driven unit like the Flex units. It is a random orbital polisher without a forced rotation feature.
@supersound58347 ай бұрын
Totally false and fake
@DetailedImage7 ай бұрын
How so?
@Lannd844 ай бұрын
Why is it fake, should i buy this product?
@karenguglielmo9637 ай бұрын
What is the cost.
@DetailedImage7 ай бұрын
@karenguglielmo963 Thank you for the comment! The retail price for this unit is $299.99. You can learn more about this unit by clicking the link in our description.
@rennydoyle8 ай бұрын
Thank you guys!! I hope you all enjoy the tool!
@Eurogloss2 ай бұрын
What happened to Australia?
@kernbelfon97748 ай бұрын
The Truth
@user-yb2tp4qf1r8 ай бұрын
On my BMW alpine white paint, I use menzerna 400 as one step polish (if I use foam pad and not microfiber)
@tony83545868 ай бұрын
Does the bottle say if it’s septic safe? Regards, Tony
@DetailedImage8 ай бұрын
Tony - Rags to Riches is septic safe!
@keitharaneta34658 ай бұрын
How do you know if it is a small load or big load? Any specific count?
@DetailedImage8 ай бұрын
No specific towel count. I tend to just use the washer drum as a guide. Fill it over half and I treat it as a larger load.
@keitharaneta34658 ай бұрын
@@DetailedImage ok great! Thanks for the info
@seabrew19 ай бұрын
Excited to try gyeon's rinseless!
@millerdetailing41769 ай бұрын
Looks like a great lineup of new products.
@joeb97639 ай бұрын
Menzerna has the best products without fillers! From aggressive cutting to fine polishing. I wish I could still detail cars.
@IcarusTECH10 ай бұрын
So a whole bottle for every tire, sigh...
@DetailedImage10 ай бұрын
It all depends on your tires and what is on the surface. If you have extremely dirty tires with lots of old dressing layers, you could use a 24oz bottle to clean 4x tires.
@user-lc8bp7yk2x10 ай бұрын
Beautiful job!🎉
@dillon59910 ай бұрын
So is one multimatch 3 big enough for Correcting? And how long does the battery last on 50 percent and higher?
@DetailedImage10 ай бұрын
You can get 5 - 15 hours of operation depending on the setting used. You can certainly use 1x light when correcting, but we generally recommend pairing the Multimatch with overhead lights and sun (if possible) to help show various imperfections during the correcting process.
@dillon59910 ай бұрын
@DetailedImage yea I'm in a garage that's big I got the overhead ones it's good enough just the sides are really dark
@TruckXaleRepair10 ай бұрын
Wow 😮
@steverinaldi89011 ай бұрын
What’s the difference between F4 and Premier? My car is ceramic coated and I just did a decontamination with Iron and then applied Premier. Looks amazing and 3 years so far since the original IGL Ceramic was applied but still uncertain what F4 does compared to Premier.
@DetailedImage11 ай бұрын
F4 is a paste product with graphene, while Premier is sio2 based and features a spray on application.
@charleneaviles922811 ай бұрын
How do you know when to switch the clay out? How often do you do that when doing a car?
@DetailedImage11 ай бұрын
Charlene - You want to constantly massage the clay bar to have a clean area to wipe. Once the bar has so much contamination that a new clean side cannot be massaged out, then you will need to swap to a new bar. I personally break each bar into various pieces and can get many applications as long as the vehicle is not deeply contaminated.
@LB83.11 ай бұрын
Does it fix deep scratches??
@DetailedImage11 ай бұрын
It depends on the scratches and how deep they are. If paired with a wool or heavy corrective pad you can remove a great deal of imperfections. However "deep" scratches makes it seem like they are through the clear and in those cases you will have to wet sand for proper removal.
@LB83.11 ай бұрын
@@DetailedImage wet sand with 2000 should be oke maybe beteer to go to a pro 😅thanks for the rep tho
@millerdetailing4176 Жыл бұрын
Great coating and Bliss was the icing on the cake very slick, thanks Detail Image.
@DetailedImage11 ай бұрын
Happy to hear that you are enjoying the Aquatek items!
@albertcarr574 Жыл бұрын
Nice video, do you have to use a polisher after you clay? Thank you.
@DetailedImage Жыл бұрын
You do not need to polish after claying. When using a clay bar you are removing embedded contamination, cleaning the surface and prepping it for polishing or protection. If you have any imperfections in the paint, polishing after claying is the next step.
@albertcarr574 Жыл бұрын
@@DetailedImage thank you for responding, just so I can be clear, after I''vd played, I can use a spray wax or in a can, correct? Thank you once again, can't wait to start claying.
@DetailedImage Жыл бұрын
After claying, you can protect with a wax if desired.
@willsrestorations Жыл бұрын
I'm just shaking my head and wondering where you people actually come from and where you get your information from. It's got to be the most ridiculous thing to cut C2V3 50/50 On a second application as your introducing water to a freshly coated car. I wish there was a fact checker for all you guys out there making these stupid claims and getting all these uneducated so-called detail is to believe in your process. So delusional man. As a certified g-techniq installer I can tell you 100% to never ever cut this one to one. Nowhere is it recommended by the manufacturer to ever do something so silly and ridiculous. Yes sir everyone's a detailer today right after they watch videos like this
@noelsaw Жыл бұрын
I just applied C2V3 today on top of a car with CSL (1st layer) and ExoV5 (2 layers). I am going to wait about 2 days before washing it. The water beading is already insane with CSL and ExoV5. Can’t wait to see how this three layer combo works out!
@joestewart89667 ай бұрын
hey man did you lose any of the hydrophics when topping the vehicle with c2v3,or can you not tell? How do you like it?
@noelsaw7 ай бұрын
@@joestewart8966 I did not lose any of the hydrophobic properties after applying C2V3.
@joestewart89667 ай бұрын
@@noelsaw thank you for the response boss
@MrJonjonoo7 Жыл бұрын
Mount plywood, then attach to wall for most secure mount.
@redbaron2448 Жыл бұрын
Wow no before pictures, where's the scratches, This is a Terrible video, won't be subscribing 😂😅
@DetailedImage Жыл бұрын
Sorry to hear that you did not enjoy the video! This video is a how-to video, showing you more detail in how to use the product. At the end you will find a 50/50 shot showing the imperfections there at the start, and the finish after use of the compound. We will however keep your suggestions in mind. Thanks again for watching!
@ryanhazlewood1693 Жыл бұрын
When polishing the edge do you tilt the polisher slightly towards the edge or away from it at all?
@DetailedImage Жыл бұрын
Ryan - I am generally mindful of edges and slightly tilt away when polishing. Just be sure to keep the pad spinning during the process.
@charlesdouglas2877 Жыл бұрын
How long does the protection last?
@DetailedImage Жыл бұрын
WetCoat lasts up to 12 weeks.
@albo9122 Жыл бұрын
Can you apply it as a topper over other brand ceramic coating ???
@DetailedImage Жыл бұрын
EXO v5 can be applied as a stand alone coating, or on top of another coating such as the Gtechniq Crystal Serum Light
@albo9122 Жыл бұрын
@@DetailedImage but can it be other ceramic coating beside gtechniq?? Eg adams or car pro
@DetailedImage Жыл бұрын
It can be!
@thegreenman555 Жыл бұрын
Cloae.. Jag - you-are. Where the ‘J’ in Jag is pronounced as in ‘just’ - Juh. But you were closer than most - i’ve often heard ‘yag-war’ 🙈😂
@jamesthorne222 Жыл бұрын
Thanks for your advice, so many brands with so many options, you've helped immensely in my search for the right product combo.