Why would you call the pressure SENSOR a switch??

Thank you!!!

Thank you

A few issues that Bayview does not address: They miss the fact that two engines were available so is the same procedure for the CXS Trim level which has a 3.6 L engine? Also they missed important tips: Before you start the engine must be warmed up and the top filler cap should be off. This makes flow out easier and as much Oil as possible leaves. Almost all Car Guys do this by raising the car up by a Floor Jack and resting it on Stands not using a professional Auto Lift. That means it is a lot harder to deal with the Filter. If you are using Car Ramps then you first need to take off the front Splash Guard under the frame because it hangs down and blocks the car from getting up Ramps. Always install a new Gasket-Ring on the Bolt you remove to drain the Oil. The Ring on that always flattens out over times so will eventually start leaking. I've changed the Oil on many different types of cars since I bought my first one in 1974 but after seeing where GM placed things, I'll save myself a lot of hassle and let a Professional mechanic do it in 15 minutes. The cost for a good shop to do this is only about $40 more than me doing it and that doesn't include having all the needed tools and time spent buying everything.

Make sure is on trip A

Exactly what I needed to see

exactly what I needed to see.

Many thanks! Very clear instructions.

9:52 thanks for your straightforward explanation. On vacation when it happened and was able to successfully complete this repair with this easy to follow video. Top notch.

Can you do this in total darkness? I can kind of see things.

Top break bulb #

For my 2007 its a ten hour job to take the whole dash apart and all the components to access it. I saw a video years ago and. Cut the access hole in the bottom out.

Thank youu

You sound just like Jim the car guy 😅

The slide pins on my 2000 are identical in the front. They both have rubber sleeves on the ends of the pins. On the rear they are different

Very helpful. Thank you!

you do not have to take the tank all the way out to change the pump! it takes me 14 min to change a pump on a mustang 2001. but for the life of me i can not figure out way my mustang does not start on its own. if i use starter fluid it runs fine with no problem.

I come back to this video about 2-3x a year lmao

Does the parking brake need to be engaged when I loosen it or?

No, my steering knuckle isn’t coming off the bottom control arm at all. Not sure why yours just came off?

Great information. Clear step by step instructions. Thank you!

After replacing my fuel pump, it took 4 hours to re-install the tank (I did it by myself using jack stands and 2 jacks) and all went well except the fuel gauge quit working after a few days when I gassed up again. I had to repair the wire to the float assembly before re-installing everything but I might not have done as good a job as I thought. Can the fuel hat and pump assembly be removed without completely removing the tank (can it be dropped just enough to remove the hat bolts and pull out the assembly)? I want to avoid taking the tank completely off if possible.

How do you turn up brightness on screen

GREAT teaching. Thanks, Boss. Grateful.

Thanks to you I knew how to do it, thank you very much, Greetings from Chile.

👍👀👍

Hi what type of filter for honda hrv for cabin and air filter?

Those wire brok caz they make it lit to short

Its easy to put that wire and check it

I got to replace mine. Thanks for the video brother!

Thanks 🙏

Excellent video. Perfect narration. Clear camera work. Very thorough and understandable. I appreciate your recap at the end. This will make my brake pad job much easier. Thanks!!!

Thanks for the video brother, i come here every 6 months per oil change

😮😮😮😮

QUESTION: At 3:59 to 4 Minutes, and 1 second (into the video), when pulling the Rotor, SOMETHING POPPED. the caliper lies on that. in the video - towards the end, re-assemblying, i didn't see how you put that one back? any help? SERIOUSLY GREAT, EDUCATIVE video. adding just the last part of putting everything back together SCORES a 10/10.

Thank you so much for taking the time to film this. Not easy. Enormously helpful.

a very GOOD teacher. step by step instructions. hey Boss, you're the Best. i appreciate you.

Appreciate the video brother.

What are the symptoms to this going bad?

Dude way wrong on this

Muchas gracias señor!!

Thank you. Stuff like this saves a ridiculous amount of money nowadays

Didn't really need to replace it, you could have just cleaned the carbon out...🤦‍♂

I made the mistake of removing the parking brake cable from the lever that attaches to the brake shoe. I can’t get the spring back enough to get the lever back on. Any help??

Are you just resetting it or turning it off? Will service engine soon light come back on in the future if there is a real problem that needs to be addressed?plz lmk or if anyone randomly reading this knows lmk ty

Thank you!! I followed your instructions and got the job done.

Clear that phlegm

Do you have to put gasket sealant on it

Great Video!

Do you need to take off the door panel on a 2013 santa fe sport