I was wondering if you could help me out here, I have a 2008 ML350, while taking out the radiator, I mistakenly pulled the AC line from the Radiator side, Freon vented out in the garage and it was not a comfortable moment. I have since not driven my car or even turned the key, it stayed in the garage but did not cover the pulled line but it stayed in the engine bay. The Compressor hoses are still connected. I am worried if I need a flush? A new condenser? Or put the hose back and go to a garage and have it recharged? Thanks for helping out.
@arsentrucking78834 күн бұрын
@@Smudg put the line back on vacuum the system out and recharge it and you should be good
@Smudg4 күн бұрын
@@arsentrucking7883 I am going to try that. Thanks for your answer.
@HectorGarcia-rr7lu17 күн бұрын
Yup blocked my egr bc I didn’t want to buy a new one and still had the whining sound! It barely happened so the exhaust soot hasn’t started to show yet! After I ran it for a day or two found out it’s the same one you’re replacing
@stevemabry671817 күн бұрын
Lost oil pressure sensor, or wiring harness, replace both them, hopefully it's not the ECM
@williamtizta0924 күн бұрын
Can you tell where is located on a 13 please
@paulfitch959729 күн бұрын
You said it just right. Thank you sir
@nathannovak4450Ай бұрын
Is that at the new house?
@arsentrucking7883Ай бұрын
No it’s somebody else’s house
@gabemendiola1265Ай бұрын
I just got my truck not to long ago and this same noise started to happen as well. What's the exact part id be asking for when u get to the shop?
@arsentrucking7883Ай бұрын
@@gabemendiola1265 most likely your exhaust manifold gasket
@don_CAT611Ай бұрын
Can you post the part numbers for the flywheel you used and snap on clutch brake ? Also why that particular clutch ? What about eaton easy pedal 2050 ?
@arsentrucking7883Ай бұрын
Call inland truck parts 4024649393
@MarcusBrown11Ай бұрын
Yeah Man!
@TORAH-613Ай бұрын
Im fixing to extend my truck frame. Im changing out my suspension to a better one than what i have. Im kinda weary with cutting the center of my frame and had thought about just adding the length to the rear of my frame. That way i can drive my truck to a welding shop, have them weld the extensions on and drive it back home. Then i can do the rest by swaping over the suspension myself and save several thousands of dollars.
@barefootking6347Ай бұрын
What year
@arsentrucking7883Ай бұрын
2011
@marvintomol181Ай бұрын
this is the problem of my cat now...The screen always show "atmospheric pressure sensor short".
@samshambles3912 ай бұрын
And then what?
@arsentrucking78832 ай бұрын
And then you feed it to the cow 🐮
@Deafshot2 ай бұрын
Got my first overweight in Hidalgo. Accidentally took a wrong turn and got pulled over, ticket is 10k. Company won’t pay, I’m honest f*ck.
@arsentrucking78832 ай бұрын
Wow 😮.
@arsentrucking78832 ай бұрын
You better start looking for lawyer
@Deafshot2 ай бұрын
@@arsentrucking7883I found 3 but they all say more than likely take it down to 7k but they won’t do payments. My record is clean, this is my first offense, I honestly can’t believe how my company and states treat us truck drivers. A DWI is cheaper or the same as my ticket 🤦🏼♂️
@creativehands10942 ай бұрын
Can it be done that easy without the cutting fluid?
@exsilia49892 ай бұрын
where is the oxygen sensor located?
@arsentrucking78832 ай бұрын
Depends which one there’s a couple of them
@exsilia49892 ай бұрын
its a 2011, are the oxygen sensors located on the cat converter by the NoX sensors? are they located before and after the cat converter?
@exsilia49892 ай бұрын
also been told its by the turbo
@arsentrucking78832 ай бұрын
There’s one upstream and one is downstream
@TopUpLogistics2 ай бұрын
Arsen is my grandfathers name . Are you near Los Angeles? I need an apu installed on my Freightliner
@arsentrucking78832 ай бұрын
No I’m not in la I’m in the Midwest
@TopUpLogistics2 ай бұрын
I need to make the holes to install a thermo king apu . Do you anywhere in Los Angeles that installs apu or can at least drill hole so I can go pick up the apu I bought off someone on fb marketplace
@donniewagenbox682 ай бұрын
where is it on a lee c13?
@arsentrucking78832 ай бұрын
I’m not sure about c13
@donniewagenbox682 ай бұрын
if this thing is bad, will it throw a code?
@arsentrucking78832 ай бұрын
No sir
@MereSkink2 ай бұрын
Talked to my union rep about how to transfer to mechanic tech because i saw they was looking for mechanics and just went to apply and the application site was token down
@arsentrucking78832 ай бұрын
Nice 👍
@rasimbond47673 ай бұрын
Take a break my man.. you work too much..!!
@shawnmichael47853 ай бұрын
Anything I need to study before face to face interview. I been trying to look up delivery trucks to learn the basics but I can’t find nothing
@arsentrucking78833 ай бұрын
Don’t worry you’ll be fine there’s nothing special it’s pretty basic stuff
@shawnmichael47853 ай бұрын
I got face to face interview on Tuesday with hiring manager. I got basic mechanical experience so I got to fake it to get on wish me luck buddy
@ChrisMcCutcheon-wj2pp3 ай бұрын
I am having a fit out of my 07 century, gouges not reading, very poor power, it has never fail to start, no check engine light, doesn't come on at all
@arsentrucking78833 ай бұрын
Check your boost pressure sensor
@ChrisMcCutcheon-wj2pp3 ай бұрын
@@arsentrucking7883 I do get erratic reading on all gouges on that side, boost pressure comes and goes, if it's raining all work fine, no water in truck either
@arsentrucking78833 ай бұрын
@@ChrisMcCutcheon-wj2pp Sounds like you have a wiring problem
@ChrisMcCutcheon-wj2pp3 ай бұрын
@arsentrucking7883 have any recommendation where, I am in Nashville tn, I have already spent 20k, no shops around here are honest
@ChrisMcCutcheon-wj2pp3 ай бұрын
@@arsentrucking7883 could it be the battery in the ecm
@lebiismaelbonilla45653 ай бұрын
What’s the part number?
@arsentrucking78833 ай бұрын
Sorry I don’t remember you’re gonna have to call the dealer
@screamingeagle95533 ай бұрын
Well it happened! You are right about this is a must have upgrade to the kitty kat! Monday I lost my fill cap and even though I only lost a 1/2 gallon it made a mess! The TA didn’t have the right fill cap and had to wait next day to get it at part store. I called PDI and told them the direction I was headed and they sent me to a shop that had it on the shelf! Just installed it and now hopefully this is a worry free part. I wish they would make a delete plate since I don’t use this to fill my oil.
@Chris-vc1dh3 ай бұрын
People's thinking is sick, they think van can be scratched dented and look like pigsty just because it's a work van , sick thinking...
@lucifur9993 ай бұрын
Do you need a drivers license??? What type of tools needed to start off???
@arsentrucking78833 ай бұрын
Yes you do need drive license, just a basic start up tools nothing special
@lucifur9993 ай бұрын
Hello and ty... I have been a auto tech for 15 years in private garages... No diesel experience or diesel tools... Should I still apply??? What type of tools are needed in the beginning??? Ty...
@arsentrucking78833 ай бұрын
Just basic tools nothing special.
@GregoryBirulkin3 ай бұрын
With the startup for tooling cost & the Insanity involved with his job, it's no wonder there is such a high dropout rate. I Started working professionally on vehicles starting in 1984.
@nataliefilonova81963 ай бұрын
😮
@nataliefilonova81963 ай бұрын
The benefit from such job - Don't need to go to gym! 😊
@innakarpyuk47563 ай бұрын
What up you tube
@s.f.mworldwide72423 ай бұрын
I have this issue on my paccar and you sir just helped me chase it down. I been looking for this problem for months I too thought it was My turbo
@arsentrucking78833 ай бұрын
Most likely that your exhaust manifold gasket
@MrSip4life3 ай бұрын
What are the types of repairs that you do in house? Are you required to rebuild engines and transmissions?
@arsentrucking78833 ай бұрын
Everything but we not rebuild transmissions or engines
@screamingeagle95533 ай бұрын
I put a hot side turbo blanket to help with my EGTs and it made me feel the same way brother! It’s red so when I have the hood open it always catches my eye!
@screamingeagle95533 ай бұрын
Thanks for posting this! I have an AirDog 165 that I took off my powerstroke when I sold it and I was told by AirDog that I couldn’t do this because it couldn’t support the supply and demand for my MXS! I think they want me to buy the 200. On my next home time I thinking on adding it anyways. I’ve changed pickup tube in both tanks, splitter valve, fuel lines and it did help some but still rough. After seeing this I’m going to now. Thanks again!
@ajkemer4 ай бұрын
Starting rate for a master diesel mechanic all 7 ases? Plenty of experience. Do there shops have ac?
@arsentrucking78834 ай бұрын
No a/c
@ajkemer4 ай бұрын
@@arsentrucking7883 same with current shop
@arsentrucking78834 ай бұрын
@@ajkemer Sometimes we don’t even have Heat
@sheldonsewell50594 ай бұрын
So I have a 379 but am doing oversized loads and heavy loads. I want to do a roll back on mines. Just extend the frame. What do you recommend me doing? For the drive shaft and other components??
@arsentrucking78834 ай бұрын
You have to figure out the wheelbase so you can used 2 carry your bearings You don’t want any new driveshaft be past 65 inches
@rayberry004 ай бұрын
Tighten up your turbo bolts That should fix it
@markhope11914 ай бұрын
Question will a return line make trk suck air 3406e
@arsentrucking78834 ай бұрын
No sir. Return line under pressure so if you do have a leak you would have a diesel fuel leak.
@markhope11914 ай бұрын
@arsentrucking7883 i hav a air dog built into return line?
@markhope11914 ай бұрын
Would that suck air ?
@arsentrucking78834 ай бұрын
I don’t think so
@markhope11914 ай бұрын
@arsentrucking7883 i ha a air dog system that return fuel goes bac into 2nd filter splits of goes to tank
@CurtisJines-su4kk4 ай бұрын
Yes then we’re you weld it together it’s between the axels yur right
@raymundocervantes68034 ай бұрын
No entiendo mucho ,pero creo que me ayudará. Thank you
@MediCali9514 ай бұрын
Just took the test and failed. It was extremely difficult. Some of the stuff I didn’t even learn in college maintenance courses. Any advice? I feel like I’m wasting time in school if you don’t need any certifications just pass a test
@arsentrucking78834 ай бұрын
Sorry to hear that man
@vipanbasra14464 ай бұрын
I have same issues. Looks 2 gasket out. Huge noises can u gave me part number or how to explain what kind of gasket is called
@arsentrucking78834 ай бұрын
Exhaust manifold gaskets
@vipanbasra14464 ай бұрын
Thanks i see u not remove turbo just remove top egr components and few lines. If i try to fix it by self what another parts i need to buy like egr gasket etc. Please explain deply
@arsentrucking78834 ай бұрын
@@vipanbasra1446 I will try to record another video Today because I do have one truck with the same engine at the shop
@vipanbasra14464 ай бұрын
@@arsentrucking7883 awesome thanks for helping
@Vakabon363 ай бұрын
@@arsentrucking7883 where are you located please?
@ElDIABLO82885 ай бұрын
What is the fuel glass ball called?
@arsentrucking78835 ай бұрын
I think it’s called see-through eye for the fuel lines it’s made by Cummins
@jcbartman16185 ай бұрын
Are they having layoffs. I read they are laying off 12000 online. I have an interview tomorrow at 10am. I have been working as Diesel mechanic for 17 years with American Airlines in there Automotive Department. My wife took the kids to another state I barely see them so I’m going to leave AA.
@arsentrucking78835 ай бұрын
Mainly they letting off the management
@mauriciomoreno97915 ай бұрын
Can’t fire union
@siliogarcia14195 ай бұрын
Did you end up leaving AA?
@stevekecser58205 ай бұрын
Thank you, very useful info! I am about to take the A/C compresor off of mine, because I need to change the pulley bearing in it, tried to take it off the pulley without pulling out the whole compressor... basically impossible.