Small size wires from motor winding temperature sensor
@cooltechhvac455510 күн бұрын
Small wires for Motor temperature sensor
@kamalsubramanian400311 күн бұрын
😮😮😮
@santoshnaik9175Ай бұрын
Wrong producer to replaced the bearing 😡
@cooltechhvac4555Ай бұрын
Please explain bro
@vCLAYMOREvАй бұрын
Thank you, sir. Im having an issue with 24v fuse keep blowing, making the board not have alarm code 31. What could cause this I checked all the safety switches etc.. no shorts were found maybe the board is defective and needs a replacement?
@numanmirza9584Ай бұрын
The reason is the high motor temperature
@hvactechnical3507Ай бұрын
Please Upload Füll video explain control waring refrirnt cycal
@marcelo.gero82Ай бұрын
Consejo para retirar el motor coloca dos esparragos sin la cabeza torks para que el bobinado salga parejo y no se lastime😊
@anilkulal4933Ай бұрын
Normal winding temperature ethre aan?
@cooltechhvac4555Ай бұрын
91c vare ok
@cooltechhvac4555Ай бұрын
113 c high temperature alarm vannu off aakum
@anilkulal4933Ай бұрын
@@cooltechhvac4555 okay
@numanmirza9584Ай бұрын
Low gass issu side glass must be clear
@guillermorodriguez8707Ай бұрын
Bueno días. Cuanto cobran por ese trabako
@cooltechhvac4555Ай бұрын
Good morning boss, I am only a employer. Thank you
@AnishKumar-dx4bzАй бұрын
Good 👍👍
@kamalsubramanian4003Ай бұрын
❤❤❤
@RuslanIslam2 ай бұрын
Круто, а можно описание замены фильтров на чиллере carrier 30hxc190a0632
@cooltechhvac4555Ай бұрын
Halo bro, Internal oil filter? External oil filter? Or liquid line drier filter?
@RuslanIslamАй бұрын
Привет брат, да полностью. У меня масло пропало. Нашёл его в маслонасосе
@anandvaidya84052 ай бұрын
Cannot understand Malayalam but still understood the video. Thanks 🙏🏼👍👌
@cooltechhvac4555Ай бұрын
Welcome 😊
@kamalsubramanian40033 ай бұрын
❤❤❤
@vengatsan65193 ай бұрын
Super 👌
@cooltechhvac4555Ай бұрын
Thank you
@avishkarao3 ай бұрын
Hi, can the motor housing come out by itself without the windings?
@cooltechhvac45553 ай бұрын
Winding tightly fit in the dome , need to heat up the dome
@dancingniya83983 ай бұрын
Nice Work Broii.. 👍
@cooltechhvac45553 ай бұрын
Thanks
@shintosanthosh49894 ай бұрын
Thank cheettaa
@cooltechhvac45553 ай бұрын
Welcome bro
@justinjoesph73324 ай бұрын
Then after 👍 ok or not
@cooltechhvac45554 ай бұрын
Yes boss, before it was 105 *c, now it's maintaining 87 to 91*c
@martys99725 ай бұрын
I am skeptical about the value of filling with water. For the bend radius shown in the video, you may have achieved equally satisfactory results without any filling whatsoever. Water exerts equal pressure in all directions, so it would make it significantly more difficult to bend around the mandrel. Also, any small leak would make it completely ineffective. For small bend radii, I think that using sand or salt would be better.
@cooltechhvac45553 ай бұрын
Sir, Thanks for the comments. I made 3 inch radius in half inch copper tube. Water is better option for me, easy to remove ( fleshing and vacuum) . I used the coil for a Refrigeration purpose
Please check my old videos, there's the details, thank you
@stevepersad69589 ай бұрын
Hey guys, I really admire your work ethics and there seems to be an ease of fixing these problems. I also like the slogan I see during the video presentation. " I like my job"..good job. How can I contact you. Let me know.
@cooltechhvac45555 ай бұрын
Thanks for the comments,
@AnishKumar-dx4bz9 ай бұрын
Pls share the spec
@AnishKumar-dx4bz9 ай бұрын
Good work 🤝👍✌
@jeffreyrex82329 ай бұрын
I miss the old YCAJ’s. Very very robust machines. 💪🏻
@commietube427310 ай бұрын
I’m having to do this for the first time at a plant. Love seeing a man ply his trade! Thx for the water fill tip!
@cooltechhvac455510 ай бұрын
Thanks for the comments 😍
@thomaskeeter4585 ай бұрын
@@cooltechhvac4555 would you be willing to make one at 3/8 inch and send it to someone?