Just curious where you purchased the part! I see many sites. What is average cost? Thanks! I’m going to replace it on my 2011 Nissan.
@TechTimeWithT6 күн бұрын
www.rockauto.com
@TheMotr4u6 күн бұрын
Complete waste of time ...
@TechTimeWithT6 күн бұрын
You must be a mechanic 🧑🔧
@goku101ssgss922 күн бұрын
What if the pulley is short of loose? Do I change the whole alternator or is it still fine?
@TechTimeWithT22 күн бұрын
If pulley is loose change the pulley only…
@thingshappen919925 күн бұрын
My belt makes a quick chirp when i first start the engine in the mornings. When it rains heavily though it squeals for a few seconds the it stops. What is it?
@TechTimeWithT25 күн бұрын
I believe there’s some crack on the serpentine belt. I would replace it soon the better. I just continue and get worst with the noise. If you keep it too long, the belt snap then you got a bigger problem with the engine. To be safe replace the belt. Pretty easy and cheap.
@anisiobidavid870Ай бұрын
How can I reset, after changing?
@TechTimeWithTАй бұрын
If you have the device to reset the code do so. You can also go to advance auto or auto zone request them to reset. They will do it for free. Then, drive over 100 miles if it fixed indicator light will not come back. Good luck.
@anisiobidavid870Ай бұрын
@@TechTimeWithT Thanks for your reply. But what if I decide to drive it without resetting after the change, is it wrong or will it cause any damage? Sorry for bothering you this much
@TechTimeWithTАй бұрын
@anisiobidavid870 i do not believe car systems will automatically reset it self. But, feel free to try hoping it will go away. You can do a low risk as well - take out the negative cable terminal from the battery that will reset the whole system. The risk is that if your car required system to relearn to operate it can be very expensive. If i drive older car i would do it if don’t have the device to reset.
@TechTimeWithTАй бұрын
Also, if you don’t reset the code how would you know you actually fixed the issue. Code can be from upper or lower stream O2 sensor. Then there’s a potential bad Cadillac converter can cause indicator light turn on. I would say at least do the negative battery terminal. Good luck 👍
@RedLion502Ай бұрын
Thank you 🙏!! You explained everything so clearly and this helped me a ton!
@TechTimeWithTАй бұрын
Glad the video help!
@carlcannedy2669Ай бұрын
Thanks a bunch
@TechTimeWithTАй бұрын
👍
@jgriff635Ай бұрын
What size lug nut socket
@TechTimeWithTАй бұрын
13/16 inch hex socket size
@yeandiaz96512 ай бұрын
Where is this place at?
@TechTimeWithT2 ай бұрын
Field of Dreams at Venetian In Vegas.
@ajayjimmy91022 ай бұрын
Can I clean the throttle body while it’s still on or no? And do I have to reprogram it if I have to take off the throttle body to clean it?
@TechTimeWithT2 ай бұрын
I would recommend remove negative battery cable then remove throttle body to clean with throttle body cleaner only. Once removed and cleaned not necessary you fixed the issue. After you installed and drove the car over 100 miles, light indicator should not come back unless the throttle body is no good. That’s what happened to me i had to replaced a brand new throttle body. Good luck! 🍀
@Elizabeth-lj9hr3 ай бұрын
1:19
@Elizabeth-lj9hr3 ай бұрын
Do the same for passenger
@TechTimeWithT3 ай бұрын
Same way but should be easier cuz driver side has all the remote to control others.
@Elizabeth-lj9hr3 ай бұрын
It has 1 bolt. Do I take that out. How do I know what I need?
@jmcieslak03 ай бұрын
This worked for me, thanks
@TechTimeWithT3 ай бұрын
Good to hear
@stevengreen74844 ай бұрын
By the way thank you for uploading this video! I saved my mom a trip to the mechanics because of this video! It is greatly appreciated
@TechTimeWithT4 ай бұрын
I am glad the video helped out.
@stevengreen74844 ай бұрын
Will the check engine light reset immediately after installation of the new part? Or does it take a while
@TechTimeWithT4 ай бұрын
Normally, the system reset after 100 miles
@Xender3334 ай бұрын
So i replaced my 2011 doge calibers ecm and i think i need to reset the throttle u think this would work?
@TechTimeWithT4 ай бұрын
It should work. It’s brand new. When you cleaned and reuse the parts sometimes it’s no good. Good luck!
@Xender3334 ай бұрын
@@TechTimeWithT it'd refurbished and reprogrammed emc I was told to just plug it in and do the relearn procedure
@TechTimeWithT4 ай бұрын
@@Xender333 Very Nice! 👍
@kingllama12634 ай бұрын
We go to this show every year and it never fails. Hopefully we can go soon to see the new neon animals!
@TechTimeWithT4 ай бұрын
Yeah it’s amazing! First time saw t it. Neon animals?
@kingllama12634 ай бұрын
@@TechTimeWithT I meant the sea creature things. They just added them recently.
@TechTimeWithT4 ай бұрын
@kingllama1263 some day i will see it
@virtualreality5124 ай бұрын
I'm a woman who now believe I can replace my window switch after watching your clear and simple instructions. This is the best video I've seen!!! Thank you!!😊
@TechTimeWithT4 ай бұрын
You're welcome! I’m glad it helped.
@adimed72074 ай бұрын
My drum was sticked so I had to release my hand break cable No I put the new pads. So my question for the drum adjustment , should I adjust the hand break cable first or the pads withs spacer first Thks
@TechTimeWithT4 ай бұрын
I would adjust the pads with spacer first
@adimed72074 ай бұрын
Good job
@TechTimeWithT4 ай бұрын
Thank you very for the encouragement!
@dmryan83555 ай бұрын
Nice to see you back! Still got the Versa?
@TechTimeWithT5 ай бұрын
Thanks! I got rid of my Versa. First time being a grandpa needed a bigger car 🚘
@greyfox1987005 ай бұрын
Thank you! I just replaced it on my 2012 Versa SV, great video!
@TechTimeWithT5 ай бұрын
Off course! Anytime.
@Yourcomputertutordotnet6 ай бұрын
What's the torque spec for the housing ?
@TechTimeWithT6 ай бұрын
Please check the manual for the torque specs. I tightened just enough with my strength as long don’t stripped the threads.
@seanhoward80256 ай бұрын
Here's another possibility...FCA issued a TSB to REPROGRAM the PCM back in 2008. The TSB is #18-011-08. This is for a false P0139 code being flashed intermittently. This will cause you to FAIL YOUR SMOG INSPECTION!!! Most Dodge dealers will deny the TSB exists...or will try to charge you to do the work. I replaced BOTH O² sensors with new Bosch sensors...and STILL failed the smog inspection. Nice EDM beat. Lose it.
@TechTimeWithT6 ай бұрын
Thank you Sean for the notice!
@newfoundland11116 ай бұрын
Mmmmmm,dinner!!😂😂😂
@TechTimeWithT6 ай бұрын
Too soon _sorry season over🤪🤪🤪
@colinnicols53876 ай бұрын
Job successfully done thanks
@TechTimeWithT6 ай бұрын
Anytime
@colinnicols53876 ай бұрын
Well done.
@TechTimeWithT6 ай бұрын
Thank you very much for the support. Hopefully, the video helped out.
@brandonlo5116 ай бұрын
Did you jack up both sides to turn wheel ?
@TechTimeWithT6 ай бұрын
Hello. I only jacked one side only. Carefully, turn the wheel slightly.
@user-c7y7u6 ай бұрын
Sundhar gidh jai mongol ❤❤happy losar ⚘️👍
@TechTimeWithT6 ай бұрын
🙏 Happy losar🍾🎊🎉
@RobertoPerez-lr6hm6 ай бұрын
Thanks for the helpful video.
@TechTimeWithT6 ай бұрын
Glad it was helpful!
@oaneschriemer27247 ай бұрын
Lug nuts are of the wheel will turn but its not coming off
@TechTimeWithT7 ай бұрын
What’s not coming off, Lug nut or wheel?
@oaneschriemer27246 ай бұрын
@@TechTimeWithT wheel, we had to use the hammer to gently get it loose . Stuck in the center
@TechTimeWithT6 ай бұрын
@oaneschriemer2724 NICE! 👍
@aajjnnoorrtt7 ай бұрын
hey wondering what model you have because i have an 18 maxima platinum with stock led headlights, they need to be aimed and i can't find the turn screw. also no info on the web, besides questions if they moved it for the 18 year, idk they would. i haven't removed the 10 screws yet to look lol so just wondering if you have?
@TechTimeWithT7 ай бұрын
Sorry! My car is 2016 Maxima SL…hopefully, you don’t have to removed the from bumper.
@aajjnnoorrtt7 ай бұрын
ha yea just tried there's no room to change the bulbs pass or drivers side, body is in the way. so bumper it is lol thanks
@TechTimeWithT7 ай бұрын
@aajjnnoorrtt GOOD LUCK!
@frankthecancersurvivor93797 ай бұрын
you still got a coding or program
@TechTimeWithT7 ай бұрын
No coding. Everything went well!
@rehan1uk2 ай бұрын
U still had the steering warning after replacement .
@hsmith3560Ай бұрын
@@rehan1uk I am wondering the same thing. I imagine you could clear the codes with bimmercode or something like that?
@TechTimeWithTАй бұрын
Nothing else came up for coding.
@rehan1ukАй бұрын
@@hsmith3560 hi, no I have still have the steering warning , but no issue on driving , power steering is ok now , few mechanics consulted locally .no joy.so no help from anywhere. If u know any solution let me know ow .
@hanikhdir96437 ай бұрын
How do you clean it??
@TechTimeWithT7 ай бұрын
Please use the Mass Air Flow sensor spray only to spray 6 to 7 inches away from the sensor. Spray inside to get out the debris. Good luck!
@mtseng5307 ай бұрын
Nissan should be sued AGAIN for selling a car with so many bad parts. My fan went out last month too on my 2015 Pathfinder. What the hell is Nissan doing? They need to take ownership and accountability replace defective fans and CVT transmission for free. I probably will not buy another Nissan again. Take note Nissan
@TechTimeWithT7 ай бұрын
💯 percent agreed! But, I still love my pathfinder. Nissan family for us.
@DBChevy577 ай бұрын
DIY: How to Clean you forgot this part.
@TechTimeWithT7 ай бұрын
Sorry! Must use the Mass Airflow sensor spray bottle. Spray 6 inches away from parts.
@zionreigns96798 ай бұрын
Is this the rear or the front of the vehicle?
@TechTimeWithT8 ай бұрын
Hi. Located at Rear passenger side
@SensiiNips_8 ай бұрын
Did you ever use that gasket you didnt need?
@TechTimeWithT7 ай бұрын
I did used the gasket
@kaaraa-mardha19778 ай бұрын
Have you tested before replacing it
@TechTimeWithT7 ай бұрын
No testing not needed. Once replaced and drove it over 100 miles. The indicator code light gone away.
@magnificantndlovu8 ай бұрын
You should have shown us where you clean it😢
@TechTimeWithT8 ай бұрын
Sorry! Once it taken out use the mass air flow cleaner to blow out dust and debris 6 inches away. If funds not to tight replace it. Good luck 👍
@davidbarth13859 ай бұрын
I found the warmest relay, removed it, and replaced it with a working one, and it didn't fix the signal. What else would be going wrong that could be causing this?
@TechTimeWithT9 ай бұрын
Possibly, fuses
@therealcoachross9 ай бұрын
BMW needs to do something about this isht! This is the second Bimmer that I’ve had this problem with!!
@TechTimeWithT9 ай бұрын
I am 💯 agreed with you!!!!! Especially, the car is fairly new.
@clairelemoigne4679 ай бұрын
I was looking for a light bulb demonstration and I got the feeling to be back to Thailand as well for a few minutes with this kind of music I was hearing when I lived there ;-)
@TechTimeWithT9 ай бұрын
👍🙏
@thomaskris78809 ай бұрын
What problems do you feel when the Maf sensor has a problem?
@TechTimeWithT9 ай бұрын
hard time starting engine, check engine light will on and O2 sensor can go bad or getting a bad O2 sensor reading….
@hauwakwaya795910 ай бұрын
Wow you guys had fun
@TechTimeWithT10 ай бұрын
Yeah! Great times.
@salmr943310 ай бұрын
Thank you - nice video
@TechTimeWithT10 ай бұрын
Glad you enjoyed it
@peteygnyc10 ай бұрын
"Dude, your gloves! That's ok" LOLOLOL
@TechTimeWithT10 ай бұрын
Just don’t want to much grease on my hand.✋ some technician don’t even use any.
@aprilfischer330310 ай бұрын
P R O M O S M
@TechTimeWithT10 ай бұрын
🙏
@flanderz293311 ай бұрын
I started my truck when you said not too!! I moved the number 1 to number 2 like u did and started. Now it won't start and is clicking
@TechTimeWithT11 ай бұрын
Jump start the battery or tap the starter. Then try to start the car