TTC DIY Building

Пікірлер

2 ай бұрын

Those battons cuts has to be at least three rafters length, and for integrity reasons the battons cuts cannot be done exactly on the same area, it needs to difer from the previous installed batton.

@jmuse2k 2 ай бұрын

Thanks for tip. I am flat roofer trying to get into tile roofong.

@lesdorry 2 ай бұрын

why is the roof tiled first and then start with your bedding in and cutting.

@ianhoare289 3 ай бұрын

Straight bonds on the bonnet cuts I would make you do it again.

@Doncorleone44 4 ай бұрын

Looks great apart from the straight joints on the bonnet tiles with hardly any bond

@Joe74854 4 ай бұрын

Battens top to top ,use a T

@craigsimons817 5 ай бұрын

When I see things done like this it makes me want to harm myself. Roofers unfortunately don’t have the best of reputations and idiots clowning around like this doesn’t help.

@chrisomalley50 6 ай бұрын

Stupid music on a teaching video.

@allmanjason29 6 ай бұрын

Thanks for the video. Have you done a video on internal brakes because I can't workout the line set up around the profile. Thanks for any help

@christiandixon2086 8 ай бұрын

Good way to get waves in the battens, doing it like this your taking a measurement from top to bottom, should measure top to top of the batten. Especially for the fact you're using 2 different suppliers

@shaunpeck5042 8 ай бұрын

Made work for your self there mate

@whitelines3097 11 ай бұрын

A scaffold board does the job and it’s quicker !

@thomasrall7422 11 ай бұрын

It looks good but what about the muck work , let’s see how nice it looks then

@redsresearch Жыл бұрын

those battens are gunna rot out

@1971dave 20 күн бұрын

They are pressure treated battens, battens are died red and blue so we can see them when we inspect a roof,

@redsresearch 20 күн бұрын

@1971dave why r u using pressure treated boards chemicals are bad

@1971dave 20 күн бұрын

@@redsresearch jb marley red roof batten, these are the only company in the UK that can produce this type of wood, blue is made by any Forest product companies, regulations they should be red so inspector can actually see them from the ground, I don't know where you are in the world but all timber is treated in the UK for outdoor use,

@redsresearch 20 күн бұрын

@@1971dave not suppsed to be on or near your house. it off gasses

@1971dave 20 күн бұрын

@@redsresearch dude" are you for real or you just taken the piss, explain to me then after being in the industry for 50 years, what type of wood do you put on your roof on top of the sarkin to hold on your tiles,

@redplanetplasterer Жыл бұрын

Would it be better to screw the bonnets.

@anthonyashton4524 Жыл бұрын

always batten plain tiles up in 8s to the top, then fill inbetween downawards, much faster. also allows for proper gauging

@a.m.d493 Жыл бұрын

Great, detailed tutorial...lots of tips...

@rokalot2436 Жыл бұрын

A little knowledge can be a dangerous thing

@serbancatalin1875 Жыл бұрын

To many cuts in rows Should be 200 mm 3 minimum cuts

@broomhagenthe1st950 Жыл бұрын

Should of got a professional roofer in your reason for not using tile& half doesn’t make sense to me you shouldn’t be anywhere near bond on bond

@edwardbennett2072 Жыл бұрын

Great video and explained well but yeah you could have built the two corners by the time you have set them up .. great on Brickwork tho 👍

@Mt3Dpdrtk Жыл бұрын

The rule is third of a tile offset bond, but tbh water sheds from the hip and it’ll probably be fine, you’ll be surprised, I’ve seen this a lot on bonnets in particular. Definitely not good though and nothing some tile and half’s wouldn’t fix.

@stena_vlogs Жыл бұрын

What is the gap between the battens from inside of batten measurement?

@davidcaldwell4953 Жыл бұрын

Why do people put stuff out there when clearly it's not right .perhaps they just want to be famous it's not a bad job but it's not right .don't show other people if you don't know yourself.

@scottclark4363 Жыл бұрын

It’s called plumb

@garymatthews646 2 жыл бұрын

wrong= you always line for the battons

@jacksmith4484 2 жыл бұрын

Bonds fucked against bonnets

@jacksmith4484 2 жыл бұрын

Need to nick a inch

@raybans8712 2 жыл бұрын

Such a neat worker and I’m a roofer. You don’t need me to tell you about the bonds on the bonnet. You just needed a more experienced guy with you on this to point it out and you would have been just fine.

@Ratsotone 2 жыл бұрын

A well explained how to video

@rokalot2436 2 жыл бұрын

Bonnets will leak like a sieve 🌧

@mos6507 2 жыл бұрын

Geico gecko is now a roofer, apparently.

@charliemulholland9114 2 жыл бұрын

Bonding is rubbish 1 1/2 tiles to be used

@stephenwivverP 2 жыл бұрын

Rubbish it is, the leaks that will follow are gonna be puzzling to this dude. 😜

@Analstrosen 2 жыл бұрын

Is this the same thing as what Americans call masonry guides?

@tsunamitube3351 2 жыл бұрын

Your gauge is bad. It does not allow for difference in battens. Make a proper dolly or use a tape. I only give dolly's to newbies

@roofinguk 2 жыл бұрын

Nice tidy cuts but shit side lap, that’s going to leak man.

@stephenwivverP 2 жыл бұрын

Sure will. Just shows how some people (not roofers) don't understand how important it is to incorporate tile and1/2 correctly too keep the required bond and keep the roof water tight.👍

@mattcurtis3019 2 жыл бұрын

Good Effort 👍🏻

@liammullan2197 2 жыл бұрын

Tune!

@mrdogger2010 2 жыл бұрын

i can build 2 small corners in the time you took faffing around with that

@SnedzTheBricklayer 2 жыл бұрын

Was thinking the same 😐 Probably good for kicking off a lift/slab 🤔

@tonyjones7372 2 жыл бұрын

I agree, I am a retired bricklayer and we used profiles at college that was it.

@mattcurtis3019 2 жыл бұрын

U could but they wouldn't be as flat

@liamwalters5029 Жыл бұрын

I think the point is your have to go back and build the rest of the corner while there running it in , no way is anyone building two corners up 24 courses as quick as a putting up 2 profiles

@robparkinson7730 10 ай бұрын

@liamwalters5029 yeah but a couple of block corners a few corse high is a bit different to 24 high brick corners isn't it?

@kanewannell621 2 жыл бұрын

Banging

@stevens5541 2 жыл бұрын

To much fucking about for my liking

@darrenenoch2680 2 жыл бұрын

Wow that’s bad bond on bond

@Skols-se7jn 3 жыл бұрын

Bond on bond double cut more graft

@richard68380 3 жыл бұрын

Nice to see them Hips straight af. Quality work mate. Started using a green laser now, how I've managed with a chalk line for so long is beyond me.

@CrustyAbsconder 3 жыл бұрын

I have a question for your viewers. I really wanted to watch your presentation. But I got motion-sickness in less than 10 seconds. Do other people have this problem ? And what is the solution ?