Hi, my belt is worn and needs replacement. Do you know how to change or can point me in the proper direction?
@ashokmoghe80354 ай бұрын
Wow those are great. What laser is that? I have a hobby machine that's too slow and can only engrave hence asking. TIA.
@Cknoble8766 ай бұрын
Where can you buy one? Link?
@JAKOB19777 ай бұрын
what is the price of the wattage probe?
@HelmickArt9 ай бұрын
I'm waiting for my power meter to arrive So I can test my fifty watt tube.. Guessing it comes from china
@sariddle10 ай бұрын
Great info and description of what is going on with the lens and focal point but the best I think is how you use your laser to draw your example. That is awesome and creative.
@AdrianHiggins8310 ай бұрын
Subscribe
@Blimbus-Blombo11 ай бұрын
I wonder if i could give myself a tattoo with one of those machines 🤔
@tucsondog10 ай бұрын
There’s videos of people doing this. There’s a lot of screaming though
@Byangelinamaria11 ай бұрын
Thank you so much :)
@CisnerosShop Жыл бұрын
Do you lower the head of the laser with a controller, some software, or adjusting the laser bed?
@Festivejelly Жыл бұрын
Great video. With an electronic lead screw this makes the process a heck of a lot easier.
@Djmatrane Жыл бұрын
Cool! When it was new (Sr90) its shows 20mRh value. (Aprox).
@syedmuneer5628 Жыл бұрын
Super 🎉
@timothyphelix1842 Жыл бұрын
How do I figure out what tube I will need. My machine looks a lot like yours. Thanks for the video. I'll tell you what's going on. Tonight at the left side of the Tube it started Arching and making a snapping noise. I assume it needs a new tube. Any other Ideas.
@ericasmith8165 Жыл бұрын
I’m at the 3rd mirror. When I pulse I’m getting 2 separate burn holes. Doesn’t matter if it’s close or far from mirror 2. What causes that?
@antsbradley Жыл бұрын
an average multi meter probe will not insulate you properly to 20kv, please be careful before holding things directly touching the 20kv terminal, even if power is off it can still retain enough power for a while to kill you
@zoo98513 Жыл бұрын
Curve is down, is this right ?!
@geminiman2831 Жыл бұрын
Can I use the preforated sheet for co2 laser bed? What is the thickness of the sheet used in your bed?
@geminiman2831 Жыл бұрын
Can I use the preforated sheet for co2 laser bed? What is the thickness of the sheet used in your bed?
@ayhanhurses6064 Жыл бұрын
Tamda özel bıçak siparişi verdikten sonra karşıma çıktı video. Teşekkürler.
@JorgieMcCabe Жыл бұрын
i have watched a few videos before i found this one,,, thank you so much for making this so easy to do.. others make it so difficult to understand this
@bornscum666 Жыл бұрын
Great instruction video. Thank you for teaching me.
@z08840 Жыл бұрын
wow, there should be an incredible gravity along the ray to make light bend like that...
@chrisl4999 Жыл бұрын
Clear directions. Thank you
@PlatinumSurfer Жыл бұрын
One thing i would like to add is that you need to find a material on which you can see a defined spot. I used paper before and was never able to see a clear circle mark from the laser beam. Now i am using double sided tape without removing the back cover, and i an see a precise mark that makes adjusting a lot easier.
@PlatinumSurfer Жыл бұрын
Great instructions. They eased my pain. How horrible was my aligning before this video. Thank you very much for teaching me the right way. (I wish my kids would say that to me at least one time)
@railgap Жыл бұрын
IF your machine came with a glass tube from China, it is very important to learn and practice this procedure as you will be doing it often!
@MrRoberttyrtania Жыл бұрын
Hi, I have the same laser as yours. I'm looking for VENDOR settings, do you have a copy ? Thanks in advance.
@DomenicoFeltre Жыл бұрын
Has anyone had experience marking a fresh skin?
@Rohan-kk7ec Жыл бұрын
I came looking for videos and yours was the second one because the first one didn't look right/seemed too easy. But it is the same and you are doing it the difficult way. Check it out: you just cross over the same colour, then get the other 2 and cross them over under the first 2, binding the previous cross in place. repeat. done. Literally the same as you are doing except you are working on both of the same colour at a time.
@trollingisasport Жыл бұрын
I wanna stick my finger under that.
@ronwalsh83922 жыл бұрын
Best video I've ever found on aligning the mirrors. Thanks, you've saved me a whole load of ball ache.
@derek25932 жыл бұрын
ALMOST great advice.... Some of it is machine independent. As Goku would say, "what is your power level?" Your advice is only good for the specific power of your laser, so what is it?
@DR874082 жыл бұрын
Tin foil or aluminium foil saves glue gunk getting on your mirrors. Just stuck it to your tape over the mirror. Then keep adding tape.
@pierluigicolotto95702 жыл бұрын
I recommend woodglut to every beginner and not only.
@alg46332 жыл бұрын
Dude, why bother with all of this. Why not just do a ramp test?
@mcreynoldsmc11002 жыл бұрын
What softwares are you using for editing pls reply....thanks
@julioguzman51972 жыл бұрын
Barely getting a 55watt co2 laser and I find this video great to get started on my acrylic work
@linzero36642 жыл бұрын
1:26, light passed trough lens doesn't CURVE to and beyond the focal point. Actually light doesn't curve at all.
@mikkosutube2 жыл бұрын
in summary..for this machine..a 38mm lens is good for cutting thin metal for example where you need high power focused in a small area..the longer lens is for making straight cuts in softer and thicker material..in between those two is a good general purpose lens..running tests at various depths allows you to determine the focal pont for fine detail work. Thanks for a great video!
@agus_actions2 жыл бұрын
Would you be able to tell me what timing belt that is? Mine broke and I can’t find a replacement anywhere online. I don’t have the measurements. I know it’s 3m and 15mm wide but the length of the closed loop is what I don’t know
@vdsmade2 жыл бұрын
👽👍
@Zelinkondorf2 жыл бұрын
"Trust me, I'm a physicist" famous last words
@tristansidgwick13942 жыл бұрын
This tutorial is great. Explaining the difference between position and direction has helped me heaps. SO many other tutorial are just focused on hitting the center of the mirror!
@sanjayKumar-qf1qf2 жыл бұрын
What is the software name for editing
@miniature_man2 жыл бұрын
i cut that with 40 watt laser in a single pass. contact me