How to do this ON A HOLLOW DOOR???

After 2 years living with a reduced volume of water this video illuminated my mind , a professional who"s time is money recommended a new faucet but my faucet was in a to good condition. Thank you very much .

Did you put a ridge cap under the cap shingles

It worked thank you

Great, but why not show the actual meat of the video of the water going into the bucket?

My clip keeps falling off. Any tips?

So did it work? I tried something similar with our shutters but we have vinyl and a much larger triangular profile. A tube didn't seem to close much of the gap. Had to do tapered tubes for each course.

THANK YOU SOOOO MUCH !!!!

Very straightforward and helpful. Thank you for this! Just changed out a balllast in our closet.

What do i do if the hot water valve doesnt stop the hot water from going thru

Watched your video and did the deed. Fixed my problem. Thank you

What is the correct nails size? Some said 1" , 1 1/2" and 2"? I don't know what to use?

Works!!!! Just need to pull back and forward a few lot of times. Between cold and hot. Then works! Thanks

I lived in my house 10 years. I figure I should finally fix mine 😂

doing mine tomorrow!

Mines sits a bit crooked and seems just a bit to short. If I go from a 1-1/4(3.75 height) to 1-3/8(4.25 height) the 1-3/8 diameter is to fat to fit into the sink. Any suggestions?

That was amazing! I’m a 63 year-old grandma, and actually fixed our sliding door. Now my young grandchildren do not have to call for an adult to go in and out of my backyard! You explained it in perfect laymen terms. Thank you!

Thank you! So simple!

Mine has no linkage system or nut 😮😅

took a minute on youtube. spent the last 55 minutes on my back under the sink and still not working even after replacing it.

Nice job!! I would just like to note that you can get fluorescent bulb replacements that are self-ballast LED's and all you have to do is bypass the ballast. I have done so and it is very easy. The LED bulbs are approx $12.00 each Canadian on Amazon so not much more that a standard fluorescent bulb.😊

Did not fix my problem. The nut is as tight as it can get☹️Maybe c😊n tractor didn’t install properly.

Thank you so much! You are the man.

This is so helpful! I have an open cavity from a new wall installation but building an entire cabinet woulb be much more $ than what you have here that seems to work fine. Luckily half the wall is still exposed studs so this won't be too hard now that i see how to do it 🎉

You just saved me so much money, taught me something important, and made my weekend a whole lot better. Thank you!!!

Thank you so much! I tried everything and I was about to give up and go buy a new faucet. This saved me, wish I had found your video sooner!

💥Thank You!! My husband used to do this, but now he is disabled. The 2 foot high weeds finally had to be dealt with and I was at a loss. I found you on you tube and you walked me through it really well. I had to stop it a few times and rewind the video, but I couldn’t believe I DID IT!!💥💥🥳🥳🥳💥💥💥💃🏾💃🏾💃🏾 THANK YOU SO MUCH!!💥💥👍👍🥳

My slider weighs a ton. Im not sure, that this will work, Its a right and left screw.... what gives?

What should we do for to decrease the moisture of the floor

Helped me today big time! It worked, I had to reconnect the hot water supply line, turn the valve back on. Turn back off and repeat probably 10 times. Each time seeing more debris and eventually more flow. Then I hooked it back up and there was more pressure than ever! Just wanted to say that in case someone thinks it's not working. Keep putting it back together, run it, take it back apart see if you're still getting more debris and it will eventually clear out. At least ours did! So stoked!

Hello. I have the exact pump for my sprinklers. For some reason, the low-pressure switch did not shut the pump off when the ditch I pull out of ran out of water. It won't turn on. It's fried isn't it?

Thanks!

Quick explanation! Thank you!

Is this really reverse thread or a backwards video? Thanks.

This saved the day!! Thank you!

Thank you!!!

Amazing video!!!!! Other videos DONT visually show you where you put the other line!! Thank you!!

Fixed it in seconds. It was so loose it's a wonder it wasn't leaking.

The steps worked. Tried many suggestions and this worked in less than 5 mins.

Thank you!

HOW ABOUT IF THE 2X4 IS MULTIPLIED BY ZERO?

Can this be used in all TVs? I mean does this hole on back of the TV is available for all the TVs by default?

Hey Marco.

Great idea. Thanks for sharing.

This is a brilliant idea!

What if it is already on the last racket ? Would I need to get a longer one?

Very helpful for anyone that’s never seen the last method like me, thanks guy

It worked!!! I had tried about 6 different (and time consuming) trouble shooting suggestions that did not work. This took about 2 minutes and I have water pressure again! Thanks so much for posting!

Thanks!

I know you made this 14 years ago, but this was exactly what I needed! I will give you a thanks too.