Yes it looks fixed ,,,, as for the rest , well if you know - you know.
@qadirustad302 ай бұрын
God
@karloslutuns91562 ай бұрын
NIC JOB
@PorkyHontas3 ай бұрын
That cost more than going to the auto parts and buying a new one with a lifetime warranty.
@WowAmazingRestoration7863 ай бұрын
Good job
@user-qb6yr6pt8f3 ай бұрын
І шо? Буде працювать? Я вважаю виламає ту сварку на першому підьйомі
@WowAmazingRestoration7863 ай бұрын
Good job
@WowAmazingRestoration7863 ай бұрын
Good job
@ktmturbo58363 ай бұрын
Hammer on the bearing😂😂😂
@job38four104 ай бұрын
Bevel should be bigger for slag to wash out and more surface metal for weld to weld to, but since the repair comes with lifetime warranty guess it dont matter........
@ptv12505 ай бұрын
WTF just happened?? I don’t even know where to start with this dumpster fire? The .050 runout after STICK WELDING the two halves is a problem. Putting that much heat on a case hardened shaft is a huge problem. Not stress relieving the shaft is a huge problem….The lack of any machining acumen is just glaring.
@FairladyS1305 ай бұрын
Lets jump forward to see what happens when this 'master repair' is put to use. Common sense should tell us that a patch is never as good as the solid original.
@gregc15205 ай бұрын
If that is a master mechanic, I never want to see what a butcher does. The center bearing surface and gear are so far off the centerline they should quit. If that was done in the middle of the desert to make it to a repair shop i understand, not as a finish repair,
@GaisaSanktejo5 ай бұрын
Not bad, this is pretty close to what I would do for such a repair, though as someone on another channel mentioned, I would have used splines or keyways... Heat treating the repaired part may be necesary, but other than that, very nicely done!
@poprawa5 ай бұрын
Pitting from head bolt to water jacket is still present. Pitting from water jacket to combustion chamber will be burned through in no time as there are two places with half of normal separation
@alro24345 ай бұрын
Same as kzbin.info/www/bejne/jXjNdJKXe698fpI
@lawrenceveinotte5 ай бұрын
To give this a fighting chance, I would have drilled and tapped four spots around the part line to ad tough bolts, and made a larger weld, I would still only expect it to last a few days till a new part arrived.
@benk70815 ай бұрын
What a joke
@user-sp8ew8yk9k6 ай бұрын
Don’t you understand that you can’t knock on the machine chuck, there’s a bearing there, you can do it with a sledgehammer somewhere on the floor. Don’t you understand that when you use electric welding, this cannot be done in a machine, the current flows through the gearbox and bearings. I can’t look at this, my teeth are just itching. when you are welding, is it really so difficult to wrap a part of the part with any rag so that the splashes do not fly onto the gear. You point your finger “oh good job”, no it’s just crap!
@garyemerson54766 ай бұрын
What a bodge up job. How long did it last?
@-st1cr6 ай бұрын
ای دادبی داد . یه زمانی داخل ایران هم همینجوری بود الان نیست . بیشتر دنبال تعویض هستند تا . و این شده که ارزش کار ما از بیست رفته
@SuflakhanSuflakhankhan-gy3lt6 ай бұрын
Wow 😯
@phils46346 ай бұрын
No digital tooling, not even dial gauge callipers - these people are definitely doing it the "Traditional Way" simple, effective, and requiring a good degree of skill.
@Native_love6 ай бұрын
I'm so amazed at what these men can do!
@qadirustad307 ай бұрын
Nice
@interestingmechanics007 ай бұрын
wow❤
@leewilliamson34248 ай бұрын
🤨 good job but when you're done repairing that shaft do you actually go back and reheat treat that part?
@horstmuller75129 ай бұрын
Some are really poor guys. They don't earning enough money for buying safety pajamas and safety flip flops. But at least they are not chained to the machines.
@dleland719 ай бұрын
There's those damn chipmunks again! <yuck>
@RobAlpacaflip10 ай бұрын
this channel SUCKS
@dennismalcolm662010 ай бұрын
YOU MEN ARE JUST AMAZING 👏 THE KIND OF WORK YOU DO IN SUCH CONDITIONS IS JUST FASCINATING!!!.WELL DONE ✔️
@qadirustad3010 ай бұрын
Nice
@professorgamingpk366911 ай бұрын
Good work 👍👍
@yaqoobkhan420611 ай бұрын
Amazing work 👍
@robbiemckinnon790111 ай бұрын
a pavement milling machine, in a country that seems to not have any pavement........LOL
@robbiemckinnon790111 ай бұрын
oh, and, FIRST!
@HelloMobile-fn3vp11 ай бұрын
Amazange
@elyboytvmixvlog371 Жыл бұрын
Keep safe guys, your work is dangerous and heavy
@jandadkhan909 Жыл бұрын
كفو 👍
@achmadfatkhur5965 Жыл бұрын
Nice
@jandadkhan909 Жыл бұрын
Good 👍
@jandadkhan909 Жыл бұрын
Good 👍
@thayoocharkoo6094 Жыл бұрын
32 ho engine kitna tak mila ga
@donald1056 Жыл бұрын
Never did see them change any gears and one was bad - but all by hand - no power tools - of course there was about 5 people working on it also - wow
@markfiges999 Жыл бұрын
Fully rebuilt by a top line Cat Dealership and available at the next Richie Brothers Auction