@@ISHAKMAKING kuch problem to nhi aata na 307 2X4 bathroom ke liye? Kitne hight tak use karte hai..?
@ISHAKMAKING3 ай бұрын
@@rajatkshirsagar2256 8 feet
@rpwoodwork46143 ай бұрын
Edge tap crack damage waste method
@julyparin44323 ай бұрын
Wow pwede pala yang semi round bit? Flush bit Kasi gamit ko for trimming laminate.
@Abinshing3 ай бұрын
Hello sir g
@ISHAKMAKING3 ай бұрын
YES
@ISHAKMAKING3 ай бұрын
YES
@moreintrestingvlog99254 ай бұрын
How much this Laser price
@ISHAKMAKING3 ай бұрын
4k
@NicktheDIYguy4 ай бұрын
I use an 1/8 round over bit
@ISHAKMAKING4 ай бұрын
Yes
@vilalahmad28364 ай бұрын
Nice bro Good work
@ashjas075 ай бұрын
is this Corbett Teak ?
@ISHAKMAKING5 ай бұрын
Yes kajaria tile shade name corbett teak
@ashjas075 ай бұрын
Sir Kya cost Hai iska per sq ft
@ISHAKMAKING5 ай бұрын
65 sqft material plus 30 to 40 labour
@_oO00o_Ай бұрын
इसको paste wala cement lagaye ya aisa@@ISHAKMAKING
@ISHAKMAKINGАй бұрын
Yes
@dineshpuri105 ай бұрын
Finishing me koi problem to nhi aayegi na bhai me bhi iska use karunga ab se
@ISHAKMAKING5 ай бұрын
Bindass bus edge cutting perfect honi chahiye aur 1.3 ki tap 2 mm ki tape pe he use karna
@ISHAKMAKING5 ай бұрын
Baaki High gloss laminate pe dhihaan se use karna kyoki HG laminate pe bearing ke nisaan aa jaate hai. Baaki sf laminate pe to koi dikkat nahi
@satyaprakashkumar26726 ай бұрын
कंप्रेशर और गन का pirce कितना है सर please बताए हम लाना चाहते हैं
@ISHAKMAKING6 ай бұрын
Minimum price compressor ₹8500 Gun price ₹1600 to ₹2200
@user-zt1sy3hm5t7 ай бұрын
А что резаком не судьба😂
@ISHAKMAKING7 ай бұрын
Aur iske liye kiya perfect hai
@zobaidajolly1597 ай бұрын
Price
@cyrilrodrigues39718 ай бұрын
Please provide you contact number I need to buy the coffee table
@Sahil1work8 ай бұрын
❤❤
@ashokrouth48308 ай бұрын
Fine,
@rajnovelty26458 ай бұрын
Good
@rajnisurana11819 ай бұрын
Kya rate hai
@ISHAKMAKING9 ай бұрын
₹15 k
@ashish09singh10 ай бұрын
Delhi me available hai kya ?
@ISHAKMAKING10 ай бұрын
Yes
@ashish09singh10 ай бұрын
@@ISHAKMAKING charges kya hai 1 nos 6 inches hole ka for chimney in 4 inches brick wall
@ISHAKMAKING10 ай бұрын
₹1000
@ashish09singh10 ай бұрын
@@ISHAKMAKING please give me your contact number
@ISHAKMAKING10 ай бұрын
Bhot bade Wale pade hai is duniya mai 😂😂
@Pihu523310 ай бұрын
Diwal side ka darvaja bada rahata hai to kya tere ko dikkat
@Pihu523310 ай бұрын
Abe sale Ganesh Bhagwan ko kyon kat Diya hai re
@AryanSingh-tx5lq10 ай бұрын
hole installation wale hi krte h ki khud se karana hota h
@ISHAKMAKING10 ай бұрын
Hole installation wale karte hai
@user-ex6lc8hy4h10 ай бұрын
Is Channel ka naam kya hai
@ISHAKMAKING10 ай бұрын
Pocket door fitting
@AZbone11 ай бұрын
Use an edge banding tool so you don’t have a giant ass mess
@ISHAKMAKING11 ай бұрын
Okay
@samsonacc80812 ай бұрын
Lol, all the specialists on the internet. What "edge banding tool" is better than a router on 2mm edging? 😊
@AZbone2 ай бұрын
@@samsonacc8081 you could have just said you don’t know what you’re talking about. There’s other tools that will do the same job, faster with less mess.
@samsonacc80812 ай бұрын
@@AZbone name a tool that will do it faster and leave better finish on a 2mm edging. Mess is irrelevant in workshop or fitting site, it's not like he is running edging 24/7 that is what a brush and vacuum are for.
@AZbone2 ай бұрын
@@samsonacc8081 have you ever installed edge banding or anything like veneer? If so, you know you have to use another tool after you use a router, right? I built custom cabinets for 15 years and still do it on the side. I haven’t used a router in probably 14 years or more. Also, how can you say the mess is irrelevant? It creates a huge mess and the stuff is full of static after using a router. It sticks to everything and goes everywhere. It’s a pain in the ass to cleanup and will take a long time to clean up, no matter where you do it. I could do a way better job with just a file lol.
@sizeweight11 ай бұрын
Masala chaye wale😂
@chanchalasarkar950811 ай бұрын
Mdf board Big size milega kya westbengal se bol rahi hu