Thank you very much

I added more information on the components in the description under the video, according to the connection diagram, I think I'll do it a little later, and I'll open access via the link to Google Drive

@@DIYAcoustic Thank you, will sure be waiting for the google drive link. And thanks again for the components.

Thank you very much

Okay, I'll add it in the description below the video.

I bought it on Ali Express, it’s called speaker fabric. I had a thin one, I used 2 layers.

@ thanks

Thanks

Thank you very much 😊

Спасибо

Благодарю!

Thank you very much 😊

Thanks

Oil Varathane Dark walnut

Thanks

Thanks 😊

Thank you very much 😊

На максимальной громкости часов на 2, на средней около 6, всё зависит от ручки громкости сабвуфера. Я обычно слушал примерно на 30-40% громкости, этого для меня было достаточно, работала непрерывно около 9 часов. Аккумулятор 6s на 3000mAh., соответственно можно ставить ещё и ещё и пока место в корпусе не кончится, увеличивая автономность в разы.

Спасибо

Case dimensions 180x175x255. Thanks for the question, I added more information to the description under the video.

@@DIYAcoustic Thank you so much ! A great speaker

Thank you. Yes, there are files. You can write your email and I will send you the files.

Rated power: 35W Maximum power: 60 W Nominal impedance: 8 ohms Frequency response range: 85Hz-5kHz Resonant frequency: 85 Hz, new measurements I got a result of 87.5, the speakers are really very good and with good parameters.

)))

Спасибо за поддержку

:-)

Thank you

Thank you

Thanks

Thanks, wait soon another project.

Здорова, рахмат!!!

Thank you

Bluetooth speaker works at maximum volume, then it’s about 2 hours, since it has a 3000 mah, 24v battery.

@@DIYAcoustic Brother if I use 6000 mah 24 volt lithium ion battery and use the system at 60-70 percent volume then can I get backup upto 5 hrs? and are you answering for 2hrs backup on the basis of your practical experience?

You can easily calculate, knowing what is the current consumption of the amplifier. My speaker worked for about 10 hours when listening at a volume of 30-45%, maybe even more, I never discharged the battery to the minimum. Amplifier tpa3116 2 pcs. Perhaps if you use a more energy-efficient amplifier with high efficiency, it will work longer. After all, the load is floating, even the volume level of the low-frequency speaker depends. If you have a 6S battery at 6000 mAh (these are 12 cans of the 18650 type) and your amplifier, for example, consumes 1 ampere of current on average, accordingly it will work for 6 hours.

@@DIYAcoustic Thank you for your kind information and regards from India 🙂

I don't understand what you mean

What exactly you don’t understand, everything is simple, if you buy a bluetooth module, an amplifier and everything else, then on each device there is a marking of connection pins and, accordingly, the permissible voltage.

If I understand you correctly, you wanted to know how long the Bluetooth speaker works at maximum volume, then it’s about 2 hours, since it has a 3000 mah, 24v battery.

@DIYAcoustic yes i am asking you exactly about it. Thanks.

Thank you

You can buy such speakers in almost any store, it all depends on where you live. I order from Ali Express

A factory-type second-order crossover from the microlab H600 audio system was used.

Thanks

Thanks

330x184x184mm. Material 18mm

Bolehkah minta File designnya mr. Saya pengin buat

​@@DIYAcousticboleh minta file detail potongan boknya

The channel description contains an email for communication, write to me with a subject mark, I can send you the file in CorelDraw. I don't do 3D projections.

@@wotochadeexGML You wrote to me on Boosty, your chat is closed. It’s better to write to the email indicated in the channel description.

which LED exactly?

मेरी कई परियोजनाएँ चालू हुईं, लेकिन मेरे क्षेत्र में। आप वीडियो के नीचे विवरण में घटकों के लिंक से अनुमानित कीमत की गणना कर सकते हैं, लेकिन मेरे क्षेत्र के बाहर तैयार स्पीकर बेचने का कोई मतलब नहीं है, क्योंकि डिलीवरी बहुत महंगी होगी। आपके लिए अपने निवास क्षेत्र में खरीदना या बनाना आसान होगा।

Здравствуйте, ткань покупалась на АлиЭкспресс, там несколько цветов есть.

To assemble a Bluetooth speaker using a 12" subwoofer, it will be heavy in any case, especially if the speaker requires a large internal volume. For example, on my KZbin channel there is a speaker with a jbl 12" subwoofer, it weighs about 42 kg. this is a lot, you need to carry it in 2 and carry it only in the trunk of a car. For a portable one, I think the maximum size is 8", as for the power of the tpa3116, it approximately needs an 8" subwoofer, they are usually about 100w. Car subwoofers require more power around 200w and above, you can consider tpa3255. About the speaker parameters, I agree that it will be easier to assemble, knowing the parameters, you will be able to understand what internal volume is needed for the speaker, what design is suitable.

For the best efficiency of designing your Bluetooth speaker in an open environment: a closed box, a bass reflex or with a passive radiator, you will need to at least measure the impedance of the speaker in the box. Based on the result, you can understand what type of design is better suited; if it’s a bass reflex, then it’s better to bring the port forward. A closed box will play well if you buy a good speaker with low FS, a good magnetic system (full quality factor), with a small internal equivalent volume, then you can get low tuning in small dimensions.

If you use CO 08 Evo, it has fs 41.9Hz, Vas 20.7 liters. Let’s assume you assembled a closed box, square, then it will be approximately 28 x 28 x 28 cm, this is inside the case, taking into account the small volume displaced by the speaker itself, i.e. you take into account the thickness of the material and can imagine the future size of the speaker, or rather the compartment for the subwoofer. In this case the resonance will rise to 58-59hz. This is normal for clear and correct sound; you won’t hear low bass in the open air. The bass reflex can be adjusted to approximately 39-41Hz. Just use the program to see for yourself how long the port will be needed, whether it will fit inside the case or make a port along the wall with a 90-degree turn.

@@DIYAcoustic thanks for your Response ! So do you think its stupid to build with a speaker if you dont have the parameters ? I dont want to throw them away or build cases i cant reuse for anything u know. I dont need ultra low bass, 50hz and above would be fair enough

Of course, you can assemble without parameters, but the result can be very bad, for example, you assemble a case, and the VAS dynamics are very large, in the end you will get a very high setting, etc. Of course, it may be that you get a good result the first time, in fact, you can configure it after assembly if you make a bass reflex port using a port in the form of a sewer or some other pipe, selecting different lengths by ear, or use a smartphone microphone in a spectrum analyzer application.