we are same. no matter what i do. is not the same. mine so hard to set up. :(
@igoro24752 ай бұрын
Ты говорить умеешь?
@ndho462 ай бұрын
Can you share Datasheet/table for sla battery. My motorcycle have 72v 20Ah. I want setting Low and Hight Voltages chargers
@projectid74322 ай бұрын
you can ask your supplier/seller for accurate datasheet, because different brand has different characteristics although the type is the same sla type
@tecnocharps12303 ай бұрын
excelente video muy bueno, gracias
@astrajingga8644 ай бұрын
Mkasih ilmunya Mampir you
@hafidyahiaoui85454 ай бұрын
Best explanation so far on KZbin
@kkondwani5 ай бұрын
hello i also have a ZA620_M5 how can i get the SFG software
@projectid74325 ай бұрын
you can download here www.adafruit.com/datasheets/SFGDemoV2.0.rar
@kkondwani5 ай бұрын
@@projectid7432 thanks however my ZA620 is not being recognised but its turning on.. i tried everthing the manual says about connecting the wires but still nothing. on the SFG it says "open device failed, please check the password and the device adress".
@projectid74325 ай бұрын
try this 1. swap your TX and RX pin 2. check your cable (it happen to me, the cable i used to connect arduino and fingerprint looking good but when i tested using multi-meter its dead wire) 3. try using arduino code to read your fingerprint, you can download the code and instruction in the adafruit page. some of my fingerprints did not work with the software but all my fingerprint module worked well using arduino code
@kkondwani5 ай бұрын
@@projectid7432ALRIGHT THANKS A LOT
@ch._nullptr5 ай бұрын
is this Xl6009 module DC - DC ?
@projectid74325 ай бұрын
nope, it is different module.
@vishwanathsharma83927 ай бұрын
Hi, I need to use this with Raspberrry Pi. Do you know how can I use it?
@waynefilkins83948 ай бұрын
what is the distance between the magnet and encoder and does it have to be super precise?
@waynefilkins83948 ай бұрын
I looked up the as5600 datasheet and it says 0.5mm - 3mm but it depends on the magnet, in case anyone else comes here with this question. I have this board but haven't tested it yet. Going to be testing it soon :)
@huuhaa47114 ай бұрын
@@waynefilkins8394RtFm
@jetwayartisman2 ай бұрын
Diametrically magnetised magnets or normal magnets
@EternalFaruk Жыл бұрын
Hello. I have a question about your SX1308 project: Can it be used without a charger?
@projectid7432 Жыл бұрын
yes of course, but you have to remove/change the battery when it run out the capacity
@EternalFaruk Жыл бұрын
@@projectid7432 Ok thanks 👍
@mthuda2 жыл бұрын
Bang bikin 4 relay 1 tombol dong, jdi ditekan 1x untuk on off relay ke 1, tekan 2x untuk on off relay 2, ditekan 3 detik untuk on off relay 3, ditekan 6 detik untuk on off relay 4 gmana caranya ya?
@ahmadwildan36003 жыл бұрын
bisa bikin alarm mini gak pake remote? kalau bisa sy mw order
@maimunar37094 жыл бұрын
Coba buzer pasip pasang aquino mas. Berati buzer saya tidak jadi rusak