Обясни го на български какво се правиш на англичанин

Thank you for this video! Made it much easier to remove on bumper on my own 159 to replace the Xenon headlamp ballast.

Браво братле, но защо не добавяш бг субтитри.

Ако видиш съобщението, ще се радвам да препоръчаш гарнитура за главата на м57. Виктор Рейнц или Елринг

are you bulgarian ma man😉😜

Thanks👍

What's the range of a repair of a F15 X5 N57?

Did you have to program new transmission ?

I’m not a mechanic or mechanically minded and I’m doing this on my E36 Compact 316i. This is the best video I’ve found. Thank you for explaining everything and taking the time to show everything. I’m subscribing

Very instructive vidéo thank you !

Доволни ли сте от мястото където дюзите са минали стенд и рециклират ли дюзи

...did you found out which year it was built?

Hey crank...i need your help bro...i rebuild my bmw n47 as i had super worn out main bearings...all good, buy now dde not communicating...where should i start to check? Ground earth chassis is connected...thank you

Hiya, great video. My car has camshaft sensor code, upon checking the “sensor wheel “ reluctor wheel, seem lose. Do I need to fully re-time the engine. Or can I just thighten the nut ? And also what timing tools are you using please?

Do the injectors from the 2.2 jts also fits in the 1.9 jts because i can not find them

1997 s420 v-8 . I changed spark plugs and coils, Then drove about one mile to check . It was now much better ,almost like normal car should be. But I checked for water in fuel by disconnecting the fuel pipe at the exit return pipe next to pressure regulator.taking some fuel and then reconnecting the pipe. There is no water in the fuel. It has spark.it has 45 ps fuel i pressure and holds pressure. 55 psi when cranking. Cyl 1 has 30 psi and cyl 3 has 50 psi and cyl 4 has 120 psi. BUT that's how it has been and it ran and drove for past 3 months. So why crank and no start?

Wish i could find all the pics of the m52 we put on a bandsaw to see exactly where the coolant passages were. Did it so we could upgrade to 9/16ths head bolts.

10:27 No, the outside bearings are worn because of the bent crankshaft.

The real issue is the rings carboning up because of excessive oil change intervals. It's a cheap fix with a piston soak.

Hello, can someone help me, I have the same problem as in this video, my car is at the mechanic and can't find a malfunction, my car simply shuts down after 5 seconds and I can hear the fuel in these hoses as in this video, does any of you know what the malfunction is, the pumps have been checked and are working

Колко пари излезе ремонта

120-degree turn from the repair manual is just to complicate matter, why not 100nm torque??? BMW hopeless 😔 ☹️ 🙁

Bro Can u say please the second where u show where the crankshaft Sensor ist located please

Very expensive german junk.

I like that you use the proper tools

Can I do the timing procedure without dismantling the oil pan?

soo thin walls,,i bet you couldnt get past 90mm on that bore size in this block

hey i am rebuilding my m54 and have it almost ready to run but a headbolts retorque do i do it before or a time after it is running and what are the spacs

Един човек да го покаже как става като хората.

Здравей, опитвам се да се уча за принципа на работа на всякакви компоненти, както и за техните поддръжка и ремонт. Гледам много твои видеа. Обясняваш много ясно и обстойно, евала! За някой като мен, който не разбира, изглежда, че е по-лесно двигателят да се извади нагоре. Може ли да отговориш с две изречения, защо е по-удобно двигателят да бъде изваден отдолу?

I have a n20 with low compression 90psi all cylinders check timing ok check vanos ok what else would cause low compression?

whats the need of making it so complicated lol

Daje like pomogło ;) u mnie gdzie indziej była wtyczka z przodu samego bo mam komforty

Hello not boring, very helpful, not much information available , I did what you have done, was the same situation plus a damaged front strut suspension, that cause the damage on the compressor .

How do some people do an easy oil change at 20k km, i have a 530d and i change my oil and filters every 8-10k km my car has 570k km and i had 0 issues.

Oil pump?It's happened to my vw crafter!

Можеш да провериш дали е запушен радиатора като го пирнеш него и маркучите! На мен ми беше задушен маркуч,заради едни измислен майстор който беше сипал старият кулант обратно,като преди това го е източил в мръсен съд!

Здравей! Мерили ли сте при постоянно зацепена виско перка дали колата губи някаква мощност? Карам 2.8 и в момента е постоянно зацепено, интересува ме дали спъва колата, чак толкова и дали си струва да се сложи ел. перка .

I have question.The gear from crankshaft is removable?Great video.

что за ужастный русский акцент

Great video!!!!!! Thanks!!!!

If you remap dpf you have to take out the dpf filter ?

Hey, I was doing my harmonic balancer and the crank wasn’t locked correctly. When I tried to loosed the E12 bolts, the crank rotated backwards about 1/8 of a rotation. Should I be concerned about that? I have it properly locked now, but I’m nervous. Thank you!

SRS for 2006 Mercedes module located

We're do you get the plastic cover? I have the one with the original filter housing

brilliant explanation

Where did you buy the parts?

Such a good video! Thank you so much!!!

Very nice

Excellent video, thank you so much for sharing!