I think you have to put 2 clamps in each side only 1 it's not to tie it could be dangerous. When the machine is working. Thanks.
@MinhNa8 ай бұрын
Trên đó Cty nào co nhu cầu đánh bóng khuôn alo anh nhé em.
@cnmoulding8 ай бұрын
a lot of companies need surface polish. you don't know?
@inquisitive9809 ай бұрын
Just a smart-up cleanind
@cnmoulding Жыл бұрын
In this article, I aim to shed light on the real situation of China's injection mold industry, rather than misleading our potential clients. It is not a good thing to tarnish the reputation of an entire industry, and I hope to provide clarity on the matter. Firstly, it is important to note that China's injection mold industry is a significant player in the global market. The country has a large number of injection mold manufacturers, and the industry employs a vast number of people. However, there are also some challenges that the industry faces. One of the main issues that the industry faces is a lack of standardization. This means that there can be inconsistencies in the quality of products produced by different manufacturers. Additionally, there are some manufacturers who may cut corners in order to reduce costs, which can result in lower quality products. Another challenge that the industry faces is the issue of intellectual property rights. There have been cases where Chinese manufacturers have copied designs from other companies without permission. This is a serious issue that can harm the reputation of the industry as a whole. Despite these challenges, there are many reputable injection mold manufacturers in China who produce high-quality products. It is important for potential clients to do their research and choose a manufacturer who has a good reputation and a track record of producing quality products. In conclusion, it is important to be aware of both the strengths and weaknesses of China's injection mold industry. While there may be some challenges that the industry faces, there are also many reputable manufacturers who produce high-quality products. It is up to potential clients to do their research and choose a manufacturer who meets their needs and standards.
@hakankosebas2085 Жыл бұрын
nice, I wish I have knowledge of you
@cnmoulding Жыл бұрын
if you have question, you can send email to us for support
@travellinelalitvlog1382 Жыл бұрын
Superb
@ahsanjamil0927 Жыл бұрын
Hello I want to some mould from u can u make it for as my requirements?
@cnmoulding Жыл бұрын
please send your request to [email protected] we will give you quote.
@johanfransen4573 Жыл бұрын
Where to buy
@cnmoulding Жыл бұрын
you should find it in Euro market soon.😀
@limonmohammed8388 Жыл бұрын
나 이 일 잘 알아요
@limonmohammed8388 Жыл бұрын
I know this works
@MinhNa2 жыл бұрын
Mold polishing process
@cnmoulding2 жыл бұрын
yes.normal work way
@juanjosecamachoarroyo58422 жыл бұрын
Good day, in Texas there are factories where Molds are given maintenance? I am a mold adjuster technician, who could inform me! Thank you!
@cnmoulding2 жыл бұрын
it is the reason why customers want to produce injection molded parts in Shanghai, China. It will be very easy to find assistant here.
@bartovjc472 жыл бұрын
lol why did they even take out the mould for this ? could have been done straight inside the machine . Also extremely poor Health & Safety .... crazy
@cnmoulding2 жыл бұрын
ok, we will improve our job with your suggestion.
@amrozkhan24942 жыл бұрын
Hi
@cnmoulding2 жыл бұрын
@thomasadank5792 жыл бұрын
Carelless handling, no safety strap to keep the mold halves from separating .
@cnmoulding2 жыл бұрын
thank you
@Anijur.Saifi-3 жыл бұрын
Nice 👍
@cnmoulding3 жыл бұрын
thank you
@graybeardproductions25973 жыл бұрын
Damn aluminium molds lol
@sarveshmestry75013 жыл бұрын
Is there any coating done to the mould ? Or it's just a single metal?
@cnmoulding3 жыл бұрын
we make a full hardened mold, heat treat to HRC 54. About coating, every time we spray oil on the mold for Rust-prevention
@sarveshmestry75013 жыл бұрын
@@cnmoulding thank you
@sarveshmestry75013 жыл бұрын
@@cnmouldingAnd Sir when we inject plastic in the mould or cavity where does the air trapped in it goes?
@cnmoulding3 жыл бұрын
@@sarveshmestry7501 you should add a vent on the insert surface. www.chinamoldmaker.org/we-offer-transparent-plastic-product-solutions it is our experience for transparent part making way.
Too slow i would have that done in 10 mins I am the best mold setter in Canada 100% Been doing it for 23 years and stll going ,There are magnets that hold the mold in now NO CLAMPS !!!
@cnmoulding3 жыл бұрын
thank you very much for your information, hope you can share your experience to us. Look forward to your more sharing, but also hope that we have more possibilities for communication and cooperation.
@renamakui5353 жыл бұрын
Wouldn't longer be profitable to purchase and use a ultrasound cleaning machine? Gj and aprecciate ur job
@travellinelalitvlog13823 жыл бұрын
Superb
@travellinelalitvlog13823 жыл бұрын
Fantastic
@karimaaitsahel43263 жыл бұрын
Can you help me to give me in formation or video for poloshing old mold
@cnmoulding3 жыл бұрын
ok,we will prepare a new video for polish old mold and share to all the friend
@karimaaitsahel43263 жыл бұрын
Nice
@RandhirKumar-fe8zy3 жыл бұрын
which chemical is used for clean the flow path of mould
@sendogantopal88893 жыл бұрын
What we want you to make the production of meltblown turkey price of this machine. mesemeltblown.com
@matiaslanfranconi81054 жыл бұрын
Hi. Can you give me an email? We are looking for a non woven machine. Thanks
@cnmoulding4 жыл бұрын
hi we prodce mould, not machine
@mindbase50084 жыл бұрын
What is the life expectancy of a mold???
@cnmoulding4 жыл бұрын
if use prehard material mold, ususally we can keep 300k, if use H13, Heat treat material , mold life we can keep up to 1 million shots. actually all of our customer mold in our company, even mold have problem we will free make a new mold for customer, without any extra cost.
@badrudinudin834 жыл бұрын
In 2000 I entered a plastic company, as a mold making operator, I memorized almost all mold problems, then 7 years later I was transferred to injection machine maintenance, and also almost everything I knew about machine problems, in the world of plastics especially injection, was very interesting for me , that was the story of 20 years ago, now I am 4 years in the plastic world again, but the products I produce are different, and I think I miss plastic injection machines .... enjoy your work ....👍🏻👍🏻
@cnmoulding4 жыл бұрын
I hope you often pay attention to our channel and give us more advice. Share your expertise
Yo, safety hazard, always lock side a to side b before removing from the machine.
@CTGaming306 Жыл бұрын
No kidding glad I wasn't the only one who noticed that
@ShivajiBindass4 жыл бұрын
Abe mold utar ra h ki khel ra h.. itna movement kr ra h..abi sahi se ata n h tumko
@saibalbiswas78844 жыл бұрын
Nice video, do you have tool maintenance chart of both routine and thorough?
@cnmoulding2 жыл бұрын
no, you can follow our video
@71cn4 жыл бұрын
kzbin.info/www/bejne/aIe6pn6Jepp_gM0
@Tracks7774 жыл бұрын
awesome video
@cnmoulding4 жыл бұрын
thank you , I will continue update more video for this topic
@jasonwilliams13704 жыл бұрын
Wouldn't pass in America. First the clamps weren't atleast 4 or 5 threads in. Second shit job at cleaning. Third ejector pins leader pins etc wasn't cleaned. Major air burn coming your way. Sad
@eatonasher33984 жыл бұрын
Well, I wouldn't use America as a gold standard for manufacturing excellence 😂 lmao that ship sailed a long time ago! Now, if you said Germany, England, Switzerland, or even Canada, I would agree! But America? Lol nope. Btw I agree with your statement that this is hardly a maintenance procedure - they didn't even need to take it out of the machine to rub it down like they did