Жыл бұрын
Жыл бұрын
2 жыл бұрын
2 жыл бұрын
3 жыл бұрын
3 жыл бұрын
Пікірлер
@xingyepack 8 күн бұрын
nice
@SuperYoshiBrenton 4 ай бұрын
My Name Is Brenton💀
@raymundoortiz7269 5 ай бұрын
G:1 it is just group???
@ellenboyd3096 10 ай бұрын
Hi, could I ask are the containers full of liquid?
@infestus5657 11 ай бұрын
This looks so inefficient.
@GerhardReinig Жыл бұрын
Yes, really great job, because you destroyed the factory master calibration. Have fun by reteaching all positions and be angry about, why the robot no more hit same position, when you change position configuration from non-flip to flip. NEVER EVER use the fixed position or zero master calibration!!! Always use the Quick master in zero position and you are safe.
@vincentzph Жыл бұрын
My name vincent zhu,I am from China wuhu of promach company，How to feedback various mismanagement problems of China wuhu of promach company.
@RussellTHouse 2 жыл бұрын
EXCELLENT JOB! You made it VERY simple and straightforward. This procedure will work on ANY FANUC robot.
@GerhardReinig Жыл бұрын
NO! Because the factory mastering is destroyed! NEVER use this method! Read my comment.
@emanemanresuresu 2 жыл бұрын
If there are no mechanical changes (battery, as you said), NEVER DO A REMASTER. Just do a Quickmaster and you are back to original accuracy.
@cascadeanalog320 3 жыл бұрын
Thank you
@balrogbean 3 жыл бұрын
I come to THIS, and see only 1 like and ZERO comments!? Brenton, come on!
@nguyenhoninh89 3 жыл бұрын
what is the capacity?
@jackaguero5923 4 жыл бұрын
Great job Mike.
@filipspakovsky8126 4 жыл бұрын
why zero position master?? why?? your robot will be off by few degrees than it used to be, you are resetting master counts by doing zero position master
@ROBOT_G 3 жыл бұрын
If the zero position of the robot is off then everything that is taught in any frame will be off. Sure you can touchup points to correct but you are touching up to a bad zero or mastering. Same holds true to TCP (tool center point). If your mastering is off your TCP will be off as well.
@filipspakovsky8126 3 жыл бұрын
@@OfficialObituarium Im talking about the "zero position master" that essentially rewrites reference counts, that option is only used when you change the pulsecoders, servomotors... i have never seen a crash that serious that would un-align zero notches, use "quick master" if your batteries are dead and your robot will be mastered as it was when it left the factory, fanuc uses absolute pulsecoders, no need for zero master!
@filipspakovsky8126 3 жыл бұрын
@@ROBOT_G thats why master counts and reference counts should be the same as on the mastering sheet that comes with the robot, when you do zero position master, you rewrite those values. on the other hand, using quick master will put the robot "zeros" back where they were and you dont have to reteach anything, cheers
@ROBOT_G 3 жыл бұрын
@@filipspakovsky8126 depends on the situation I took this video has a how too that's it. I changed a RV and a motor yesterday ran the robot to the witness marks single axis mastered the robot. There's nothing you can do to compensate for a repair like that. Master counts on the factory sheet can be updated. Just write the new ones down. Old counts can be used in a battery zero situation as well.
@emanemanresuresu 2 жыл бұрын
@@OfficialObituarium Just teach your base. Or Userframe, as Fanuc calls it.
@AdhvikaForgeTech 4 жыл бұрын
Very informative great
@bagnoum747 4 жыл бұрын
very interesting
@jeremiahwood9901 7 жыл бұрын
!
@rahmatroshan1604 9 жыл бұрын
A marvelous combinations of mechanisms with servo motors , very nice job done.