I have just disassembled my QB78 due to a fault in that valve, the rubber seat has disappeared, I tried to fill the gap in the stem with silicone for engine gaskets, I will try to see if it is airtight. On the other hand, I see in its valve that the air outlet hole has been modified, what diameter drill bit should I use to enlarge the air outlet? How many shots does Co2 last for you like this? Regards

I was going to order the entire Motorhead/cyclone when I came across this. Thank you so much!

Why i dont have any smell from fragrence? Peugeot workers put new one in my car, i turn on it on implify and nothing can smell from ventilation

mine only produces a single pop, like every second. Changing the jumpers doesn't do anything. Ive checked ans the IC is installed the correct way, Im just not getting any sound.

thanks a million

Can you do a tutorial for the wii uDraw pad?

Thanks mate. You've saved me £50.

Nice. Is it possible to do this and get 4k on the secondary tv? Or is HD the max on this method?

Why not just put electrical tape around the blink camera so water won’t go in tru the top holes ..🤔

I use unscented aroma beads, £5 for 200g and thats enough to last years, you can technically reuse the old beads by soaking them in the essential oils

i LITTERALLY can't access the website HELP

Tahnk you so much, this is a total disign flaw

shoud be writing with string.. ☕

Why would you need a cadence sensoe and a speed sensor? I mean if you take just the cadence sensor and input the tire's circurference you get speed, the igps is a speed sensor, but there should be a version for cadence which should work as you intended.

Thanks for this I’m now back up and running

Hi, did the 3 magnets just stick on bythemselves? I have a cover of some sort over my magnetic flywheel so magnets will not stick to the outside. Can i use double sided tape? Also do i need the 3 magnet configuration on both sides of the flywheel or just one side? The spoke sensor- if i just stick that on somehow without drilling is that ok too? Thanks!! Your video is my only hope. There is no other information out there to help in the Zwift- elliptical compatibility dilemma!

Note that more modern Sky-Q boxes now have HDCP which recognises the HDMI splitter and will not transmit any signal, making this method unusable.

I'm at the point that I should be using something more stable. The XR2206 in an obsolete chip, so what's out there is probably fake, and the circuits for the kits are problematic. We as builders need a new thing. Perhaps a 555 with some transistors to get a solid Triangle and Sine wave suitable for testing common emitter amp's or any other signal amp. I really tried with these cheapo's but it's frustrating. Good Video.

Just cut down an old socket so there just two prongs left. Simple.

The year this clip got out I bought one for UNDER 2 euros!! A diy version with case and knobs...

Going to try this tomorrow! Thanks

Thanks very much,brilliant video,job now done👍

Interesting idea! I have a qb78 and knew that you needed a special tool for the valve... This is a very cheap & simple alternative!

Very good video explaining the workings of the SS2A. Thank you :)

Brilliant idea! Thanks mate :)

Am i right that the 4k signal out from the Sky Q box will be downgraded to 1080p to both receiving TVs?

just used the vid to fit the new part. i needed a torch so i wouldnt cross thread, and in my torx set the T9 seemed to have a smaller end bit that fitted. T9 was the smallest in my set.

Modern problems require modern solutions, great stuff!

hello i need some accessories for Peugeot 5008 how to contact you

hi, i have the ps3 version but it didn't come with the usb. what should i do?

This "tab" issue I've heard others speak of, could this be the root of the problem when encountering "difficult to remove" panties that have stubbornly decided to not fall to the floor when being tugged upon.

hello everything is fine? would you sell 3 complete pieces for me? I buy from you I pass your contact can it be?

You are upsolutly excellent person you save lots money thank you

I wonder if you were to put a small bit of JB welds on it, would that help prevent it from breaking again.. I haven't purchased this vacuum but i am highly considering it. This seems like a easy thing to prevent if the JB welds can be used. I would hate to use JB welds on a high priced vacuum but seems like a small preventative measure for a inconvenient problem down the road.

thank you the best instruction screw driver length and types of screws *

how do you remove the barrel from the Co2 tube

This is fantastic and will have saved so many people so much money. Thanks for this

Hello Can i Ask if you have an Idea how i do it on my Domyos el 520 ? Thx you !

Thank you gonna use it to solve some past papers

Or you can just soak the original aroma beads in essential oils of your choice??...£54...what a rip off..beware if the garage automatically change this on a service!!!! UPDATE...Yes, it works...I got some essential oils from my daughter, who does wax melts....took the aroma beads out and added 3 different oils to the 3 lots of beads...left them to soak for a few days and then put them back in the modules and refitted...boom..3 smells of your choice...

I have xbox 360 udraw tablet, Unfortunately application is unable to detect it, My xbox 360 gamepad and xbox steering wheel works perfectly fine, tablet works aswell (in games buttons work but not pen and tablet) but driver can't detect it, It works perfectly fine on my xbox 360, I tried installing application on my brothers laptop but same results. any suggestion?

Mine is a different setup and solid from 59Hz up to 1Mhz Fine takes me from 60- 3khz and the. The course will give me the upper limits past 600Khz to 1Mhz.

That's a very phallic arm

Thank you !!

Ugh, I've found a uDraw but can't see any usb input and not sure what he means by "RF receiver" at 1:27

thank you for this video. do you have a link so i can order the complete set of orings?? or at least the valve orings needed to stop the leak? TY

How long did you have to use the hot air to get the chip off? I am having a really hard time, chip wont come off despite minutes of 430 heat.

Shame it’s not wireless. Too much of a faff to be honest. I’ll stick to my ‘alternative’ Sky viewing methods using my Firestick instead.

But now your stuck smelling horrible airwick branded scents... No thanks.