Thanks for info .

Seriously need to cut your nails

I was able to press tees but I remember being super awkward and I don’t trust it came out alright…. Not ideal tool design.

how it will work in tie places ? extant 3 ft handles ?

this is a good tool if you dont have walls or ceilings in your house then it might work, just buy house without walls and ceilings and you might get it to work, it works great on the table in video

this tool works good.....make sure you can fully open the handles and get the jaws in place....you have to plan ahead because it can be hard for tight spots..

Just buy the hydraulic crimpers, easier to use and less space needed.

Anyone have this tool? There's dials right above the handle that you can set like 1-9 what's it for?

Where do I wind this

This video is to funny. It did not show the black crimp. I was going to see how he crimp it effortlessly. I have the exact tool. I’m a 135 lbs lady and doing a lot of diy crimping my pex B with this tool the only way I can crimp it is put it on the floor and crimp with all my weight into it. As of right now my worries is crimping it on the wall since it requires my full strength and weight to make it crimp. I’m sure there is a large and heavy handle for me to use out there. This crimping tool by the way is lightweight.

Nope. That will NOT work. The press body is too bulky and the T fitting does not sit properly in the jaws

not practical on site

is this copper crimper made in the usa i would like to know

Has anyone measured the force that the major brand tools apply to the fittings vs what the manual tools do? Why don't any of the major brands release a manual tool? What is the most expensive part? I see reports of successes and failures and would really love to have a manual option but increasing the risk by using a copycat tool isn't going to fly for long. Then there are copycat fittings too.

The music is awful.

Here is the correct video for the IWS-1424BN. Please take this one down. watch?v=IVnJjEMkMSE

The thumbnail for the video shows the IWS-1424BN. However, the content of the video is for a different crimper, the IWS-1424B. Big difference between these crimpers

This is not what my IWS-1424BN tool looks like at all. Please put up the correct video for the IWS-1424BN. See the link on the IWISS site for "one-step-weather-pack-crimp-tool-metri-pack-crimper" The photo of the tool there is what mine looks like and is very different from the one in this video

i need information about iws-0560 and iws-1560 , could u make the video about iws-0560 and iws-1560 ?

Make a video that discusses the tools used

good luck for "Wang Robin" waiting for another video

Good video, i teach smk (vocational high school) technical expertise in heating, air conditioning and cooling where EVERY DAY uses copper pipes, this is an example of a video with students...kzbin.info/www/bejne/qnSxcnSdiZVra5I.

It must be so hard to get in tight spaces

You can't find these crimpers anywhere

I'm having a problem making it close when trying to set on the fitting. Crimp is on the 3/4 . Fitting is A3/4 did got the wrong fitting?

Somehow mine got locked with a ferrule inside .. how to unlock it? it wont budge. thanks!

También tienen para tuberías de 1/4 de 3/8 etc gracias

Saludos por favor se trabajar con sistema de aires acondicionados

Final end result is fake🤬

greetings friends i want to know how to use this crimper to finish bare metal number 5755

Thankfully the instructions on the product page are useful. This video is a demonstration that yes, apparently somebody who knows how to use the tool can use it successfully. It has zero explanatory value. And the music seems calculated to drive the viewer insane. Happily there aren't any actual spoken instructions on the video, so it can be safely muted.

Question - i know the joint (90, coupling and stops) are special for crimping but about the copper pipe ? Does that have to special for crimping also or can u use regular copper pipes? Thanks

Just bought one and thank you for the video, great job!

I would like to see all 3 sides of the fitting crimped in 3/4” & 1/2” copper

Hola!! Sirve para terminales Dsub? Gracias

I just purchased a set of these crimpers and used them on 1/0 wire. I only crimped them one time. and it seemed to push up one side of the lug. When I tried to reverse the wire and crimp the opposite side it seemed to fall into the first crimps relief. Is this normal?

What is that work table and vice? I want this so bad

Notice how it leaves the pipe deformed at the end...

Jeepers Scooby... Based on this video, it seems you have to have XXL hands to use this tool.

It's a good idea, but why not just solder? Propress is great for repaira on live systems in tight spaces where soldering is less of a feasible option, but theres no way this would work in tight situations. Too bad because $200 is a lot more attractive than $2000-$3500!

if you crip t-joints like in the video it will not work!!

Great tool only for great brains, it looks easy to use but you need skill to use it, specially in small space

Does this hose crimping tool kit come with multiple size hose crimp collars?

Brilliant video and demo thanks. What happens if you over crimp the pipe? Can this tool be used under a bath?

Will this work for hot and cold water (eg a water heater for whole house),. In regions that have extreme winters (eg Chicago)

You are very welcome for my watching.

Thing to remember is not every nation on Earth is wealthy, these tools in alot of country's are affordable, a milwaukee and so on just isn't

i did measure mine that i recently crimp my measurement tool got one Go and another NoGo but when i measured both go and no go was fitting i did crimp it close to the ending is that normal donot want a shower leak thx

Hi, thanks for sharing your work!!, Do you know the difference betuween A-2546B and 2546S ??.

Thank you! this is just the info I needed!