Пікірлер
@ahmedhassan-lc2iq 4 күн бұрын
Hi. Why the pressure drop quickly from 8 bar to 6 bar in case unload ?
@BDFactoryEngineer 4 күн бұрын
Hello. Check the loading unloading pressure setting and check your compressor pressure sensor.
@ahmedhassan-lc2iq 4 күн бұрын
@@BDFactoryEngineer Show me pressure sensor picture
@donnyardinovri 6 күн бұрын
Do you have password main parameter
@BDFactoryEngineer 6 күн бұрын
1688
@PetrusMakgatho-sz1vo 9 күн бұрын
Gloves at least PPE
@BDFactoryEngineer 9 күн бұрын
Thanks for your Advice
@herbertjunior9001 10 күн бұрын
Interesting, what has happened to the airend, was it stuck
@BDFactoryEngineer 10 күн бұрын
Yes, it stuck 😔
@RamBabu-ev9wl 13 күн бұрын
Good job
@BDFactoryEngineer 12 күн бұрын
Thanks 👍
@Onlyprabhuji 13 күн бұрын
faulty shutdown blocked aa raha hai kaise sahi kare
@BDFactoryEngineer 13 күн бұрын
Message on Facebook, send pictures facebook.com/bdfactoryengineer
@syedaliahmad7174 14 күн бұрын
Brother pls tell the password for reset servicing of linghein L55DS-8.
@BDFactoryEngineer 13 күн бұрын
0825
@mdobaydul1045 21 күн бұрын
এটা চার্জার দিয়ে চাজ করতে হয়
@BDFactoryEngineer 21 күн бұрын
না। এতে ডি সি ব্যাটারি 🔋 থাকে
@chilchil4999 Ай бұрын
Nice
@BDFactoryEngineer 25 күн бұрын
Thanks
@wowiecaps Ай бұрын
please see in your vid that you place the thrust bearings in the wrong way. this air end will fail with in 10 seconds.
@BDFactoryEngineer Ай бұрын
Ok I'll see, thank you for commenting. But it didn't happen.
@JoaoHenriqueRibeiro-kv3rg Ай бұрын
Top, tanks
@BDFactoryEngineer Ай бұрын
Welcome 🤗
@jayanthasaranga9120 Ай бұрын
What's purposes of thermostat valve, if it damaged, then what will happened. ...is this oil line open and closed
@jayanthasaranga9120 Ай бұрын
If this valve always closed then what will happened. ...I think,oil not going to air end though oil filter, am I right
@BDFactoryEngineer Ай бұрын
Its function is to keep the temperature at a certain level. So that the temperature is not too low or too high. If it is damaged it must be replaced. Otherwise the temperature will rise. It can be operated without it, in which case some modifications are required, which is not possible with all air compressors. Hope you understand.
@jayanthasaranga9120 Ай бұрын
What's purposes of thermostat valve, if it damaged, then what will happened. ...is this oil line open and closed
@venkisunkam7896 Ай бұрын
Sir contact number send me
@DanielsKle-v1c Ай бұрын
Hey! High Pressure warning, what should do?
@BDFactoryEngineer Ай бұрын
Please change your compressor Pressure setting
@GilCartaya-xx2iu Ай бұрын
What's alarm 3 compressors ga 30
@zaqlulfasya7357 Ай бұрын
How to remove alarm sir
@davidwasicek9869 Ай бұрын
Try a wrench or socket next time
@lalitnagar9252 Ай бұрын
भाई पागल है क्या तू हमारे पेट पर लात मार रहा है
@MdAkher-r8l Ай бұрын
1000 liter air receive tank How air dryer capacity
@flaviogomes9690 Ай бұрын
Very good 👍🏻my brother.
@BDFactoryEngineer Ай бұрын
Thanks
@learnfromme7147 Ай бұрын
hello, have you experience compressor does not load? or inlet valve wont open?
@BDFactoryEngineer Ай бұрын
Please check your compressor loading unloading Valve
@GilCartaya-xx2iu 2 ай бұрын
How do you get the valve up?
@flaviogomes9690 2 ай бұрын
Show de bola 👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻 Very good my friend 🤙🏻
@BDFactoryEngineer 2 ай бұрын
Thank You Soo much my friend ♥️♥️♥️♥️
@mauricegasana6112 2 ай бұрын
Thank you so much sir
@BDFactoryEngineer 2 ай бұрын
You are welcome 🤗
@mauricegasana6112 2 ай бұрын
God bless you bro for such anazing vedio
@BDFactoryEngineer 2 ай бұрын
Thank You Soo much my dear friend ♥️♥️♥️
@karthikkm5328 2 ай бұрын
bro do you know the password for resetting maintenance interval?
@BDFactoryEngineer 2 ай бұрын
Yes ! I know! Please massage on my Facebook page.... facebook.com/bdfactoryengineer/
@drineview 2 ай бұрын
Great
@rashedulislam8217 2 ай бұрын
Great 🎉
@rashedulislam8217 2 ай бұрын
Congratulation🎉🎉🎉🎉🎉🎉
@salomaoemanuel7762 2 ай бұрын
Main Motor Converter Alarm (Overcurrent) What Causes Overcurrent?
@BDFactoryEngineer 2 ай бұрын
Please check your compressor motor bearing, motor coil
@siseblog 3 ай бұрын
If volt high from 426, how I solve it
@BDFactoryEngineer 3 ай бұрын
Change the voltage setting. Set maximum 430 volts or 440 volts. Thank You!
@alwaleedar8632 3 ай бұрын
Why you made it full, isn’t should be half full
@BDFactoryEngineer 3 ай бұрын
No Problem.
@mohdalif2421 3 ай бұрын
Motor not run can grease?
@RakibulIslam-ek1lt 3 ай бұрын
congratulation ❤🎉
@najirahmed865 3 ай бұрын
Very nice uncel❤
@BDFactoryEngineer 3 ай бұрын
Thanks
@mdalauddinislam709 3 ай бұрын
Congratulation 🌹🌹🌹🌹🌹🌹🌹🌹
@devendrakumarverma49 3 ай бұрын
Thank you so much sir
@BDFactoryEngineer 3 ай бұрын
You are Welcome ♥️♥️
@malikamirsangla3550 3 ай бұрын
What problem sari sawal ko kya hai
@BDFactoryEngineer 3 ай бұрын
I don't understand your question
@malikamirsangla3550 3 ай бұрын
Safai ke bad bhi over temperature a Raha hai sar
@BDFactoryEngineer 3 ай бұрын
Hamara Facebook page me massage kariye...
@BDFactoryEngineer 3 ай бұрын
facebook.com/bdfactoryengineer/
@malikamirsangla3550 3 ай бұрын
Good sir❤
@AhmedMostafa-di2cg 4 ай бұрын
السلام عليكم .لماذا البيرنج الاخير ركب بالاتجاة المعاكس له ؟ارجو الشرح والتوضيح
@lampakt88 4 ай бұрын
I have similar control panel on N2 Generator and option for reset is not visible. Is there any user level password needed to have rest option visible ?
@BDFactoryEngineer 4 ай бұрын
There may be a password in this case, but I don't know the password
@lampakt88 4 ай бұрын
@@BDFactoryEngineer I found it , was " 2344 " in my case , found that you have to have "full" access before reseting , not "user" access,
@BDFactoryEngineer 4 ай бұрын
please contact your compressor supplies company
@yan4iktopal746 4 ай бұрын
Hi! Thanks for video!!! what maximum operating voltage can be set in settings?
@BDFactoryEngineer 4 ай бұрын
Yes!
@bhaktimeShaktiHindutav Ай бұрын
इससे मोटर के ऊपर कोई असर तो नहीं होगा
@BDFactoryEngineer Ай бұрын
No Problem
@disastersofnature89 4 ай бұрын
বস ভাইবার জন্য প্রশ্ন উওর ভিডিও চাই
@BDFactoryEngineer 4 ай бұрын
চেষ্টা করবো ইনশাআল্লাহ
@issamchaib3041 4 ай бұрын
Can the thermostat be removed permanently?
@BDFactoryEngineer 4 ай бұрын
Yes, but to do this some changes to the oil system are required. But this will not be possible in Atlas Copco Air Compressor.
@issamchaib3041 4 ай бұрын
هل يمكن التخلص نهائيا من الثرموستا
@BDFactoryEngineer 4 ай бұрын
Yes, but to do this some changes to the oil system are required. But this will not be possible in Atlas Copco Air Compressor.
@adolesen9727 4 ай бұрын
I want to contact him but there is no telephone number that can be contacted
@BDFactoryEngineer 4 ай бұрын
Tell us what is your problem, we will try to solve your problem inshallah
@entertainmentguy4509 5 ай бұрын
Which component controlls whether the fan will be turned on or off?
@ta-rt7fg 5 ай бұрын
Good job sir , if I remove that valve totally can I solve overheating problem?
@BDFactoryEngineer 5 ай бұрын
Can but it will not be Atlas Copco Air Compressor. Because to run without it some changes in the system have to be made.