Пікірлер
@jerryg7565
@jerryg7565 Ай бұрын
Yeah, basically china made upgrade but still old tech.
@MrGregson23
@MrGregson23 Ай бұрын
I just replaced my failed Pentair Intellibright LED board with your big, bright, 12-volt, circular LED panel. It works great and lights up my pool much nicer than the crappy original Pentair. I was impressed that your kit included the gasket, the brass screw, and spacers in addition to the well-designed LED panel. Your video also showed which end of the lens goes up and how much to tighten the screw down on the ring-tightening bolt. Pentair deserves scorn for designing a poor LED panel, that only lasted 4 years and charging over $800 for a replacement LED board. Your LED panel connected perfectly to the spade connectors. Thanks so much for making my pool pretty at night and saving me from greedy, awful Pentair.
@juanleon44
@juanleon44 2 ай бұрын
4:16 Do you know where I can purchase this board. I've been looking for this for a while
@vinniesmith4316
@vinniesmith4316 3 ай бұрын
I have 2 model 602188 one is out. Can I use this and change only one? How much are they. Thanks.
@christopherfisher1694
@christopherfisher1694 3 ай бұрын
My Intellibrite has failed, and I'm considering the Pool Baron. I understand it won't change colors via the Intellibrite controller, and only via cycling power. Does it matter what setting the exisiting controller is set to? Should I remove it? What happens if it don't, and someone changes changes the setting on the controller switch? Thanks.
@AlwaysSlimShadyBro
@AlwaysSlimShadyBro 4 ай бұрын
Will the pentair app work to change the colors. Or do I just turn the lights on amd off
@michaeldamico5152
@michaeldamico5152 5 ай бұрын
For Pentair Intelibrite Assemblies that have a completely filled transformer area with the Black Potting material, your two Black, square Heat Sinks don't fit when using the hardware provided in your kit. The Heat Sinks contact the Black Potting Material. I called your Orlando, Florida office and Kyle told me to twist off the Heat Sinks, ,but they're stuck on way too tight to twist them off with a pair of pliers; I would wind up cracking the Circuit Board. Without making any modifications, an additional short spacer could be used to lift the LEDs up about another 3/16 of an inch. Please address this problem in your instructions and provide a short spacer and maybe a slightly longer screw so the assembly can be made by someone who isn't a mechanical engineer. I happen to have small standoffs in my shop, but most people don't.
@cordesruss
@cordesruss Ай бұрын
Just noticed my 4 yr old Pentair Intelibrite's Red LED is not working. I came upon your comment when researching replacement options. I've not yet pulled my light but did note your comments about filler and removing the heat sink on the new LED board. Wondering if you had success ?
@michaeldamico5152
@michaeldamico5152 5 ай бұрын
My Pentair LED Light Transformer doesn't have a single white plug on it. It has two push-on connectors. Do you make an adapter pigtail that has the two push-on connectors on one end and the single white modular connector on the other end?
@scottlicursi7437
@scottlicursi7437 5 ай бұрын
I was about to buy but I think my light also has the 2 connectors and not the one shown in the video. We probably have the same light . Where you able to rectify this issue? if so, how?
@johngrabner
@johngrabner 5 ай бұрын
My pentair controller controls the pentair light red, green, blue, white option. Is your ligth compatible with the pentair controller?
@electricalsmokealarmsandmo1564
@electricalsmokealarmsandmo1564 6 ай бұрын
Hello. I just bought one of these boards because my pool light burned out. I have a Pentair intellebrite controller and was wondering if I can still use that controller for the new pool light. I also have a spa light that is still working fine and hope it will still communicate the same.
@Milanokids69
@Milanokids69 6 ай бұрын
Let’s start a class action lawsuit, pentair is junk
@jonathansteele4881
@jonathansteele4881 6 ай бұрын
Where can I find a replacement
@pfffff
@pfffff 7 ай бұрын
For anyone with an internal transformer, make sure you test it... you can test your old light with garden light wires (they are 12v). If it is your transformer you can remove the old with a drill and hot knife (soldering iron). Easier than replacing the whole unit. Transformer is 40-50$. Not sure why people remove the heat sinks, even with the transformer you still have A LOT of room back there.. just install the new led loosely, may not lay perfectly flat but certainly fits.
@maggiebrattoli383
@maggiebrattoli383 Жыл бұрын
Are you still in business. I don’t see any current comments. I need to buy this light
@Mentorf
@Mentorf Жыл бұрын
THESE ARE CHEAP CHINA MADE LIGHTS .. WORKED FOR 3 DAYS AND BURNED OUT, THEY WONT RETURN YOUR MONEY BECAUSE THEY ARE CROOKS.
@Mentorf
@Mentorf Жыл бұрын
DO NOT BUY FROM THESE SCAMMERS. STAY AWAY AND SAVE YOUR MONEY
@stever.9925
@stever.9925 Жыл бұрын
Awww, awww, awww...
@ensolutionstudios2556
@ensolutionstudios2556 Жыл бұрын
Is this brighter than the Pentair original one?
@matthewbishop2367
@matthewbishop2367 Жыл бұрын
I’m planning to purchase but what if my current Pentair 5G RGB light doesn’t have the quick connect shown in this video?
@germanolarte1861
@germanolarte1861 Жыл бұрын
buenos dias ,estoy en colombia y no hablo ingles puede alguien contestarme en español
@j7430g
@j7430g 8 ай бұрын
Puedo auydarte si necesitarla con esta conversacion.
@johnp1794
@johnp1794 2 жыл бұрын
Wandering if this will work for my Hayward Colorlogic light? Have been looking for years for a aftermarket fix!!
@jmo6722
@jmo6722 2 жыл бұрын
Cheap thin Chinese knockoff - I mean just look at it. The heat sinks are not as good as a water cooled affect by putting directly against the metal.
@jamescarl8156
@jamescarl8156 2 жыл бұрын
I bought this two years ago and still can’t find anyone to install it.
@ashlyncummings9429
@ashlyncummings9429 2 жыл бұрын
Can you use your light with the pentair app?
@floridasunseeker8905
@floridasunseeker8905 2 жыл бұрын
Florida Sunseeker provides spade connectors by default. We do not provide the quick connectors in the video unless requested as they are very uncommon.
@MBSF98
@MBSF98 3 жыл бұрын
Beware, this board doesn't really work for the 120v version of the light. I bought this board for my 120v Pentair Intelibrite 5G light from Florida Sunseeker, but the transformer takes up more room at the base of the light so there is no niche for the replacement board to fit into, as there is in the 12v light. I contacted customer service and was told I should remove the heat sinks from the board, as they are not necessary, and then the board would fit. I was hesitant to modify the board so I told them I wanted to return the board. They then charged me for shipping and an additional 20% restocking fee for my return. Needless to say, I am disappointed with their customer service. Update: They have now agreed to give me a full refund.
@AlwaysSlimShadyBro
@AlwaysSlimShadyBro 4 ай бұрын
Fuckers
@MBSF98
@MBSF98 3 жыл бұрын
Beware, this board doesn't really work for the 120v version of the light. I bought this board for my 120v Pentair Intelibrite 5G light from Florida Sunseeker, but the transformer takes up more room at the base of the light so there is no niche for the replacement board to fit into, as there is in the 12v light. I contacted customer service and was told I should remove the heat sinks from the board, as they are not necessary, and then the board would fit. Given the discussion in the video of the value of the heat sinks, and my general hesitancy to modify the board, I told them I wanted to return the board. They then charged me for shipping and an additional 20% restocking fee for my return. Needless to say, I am disappointed with their customer service. Update: They have now agreed to give me a full refund.
@jmo6722
@jmo6722 2 жыл бұрын
Only after you exposed them
@pfffff
@pfffff 7 ай бұрын
It will fit. You can just turn it slightly and mount on one of the other posts. Or just have it sitting a bit looser but attached to the top pole. It does in the housing.
@solo0071
@solo0071 3 жыл бұрын
Where can I purchase this or something similar
@datsuntoyy
@datsuntoyy 3 жыл бұрын
I was trying to see if it was worth replacing my std bulb with a low voltage color LED. After seeing this, I think white is all I'll ever use.
@finselbuch
@finselbuch 3 жыл бұрын
It's not N for North. It's N for narrow angle, or W for wide angle.
@MrMadeinthe80s
@MrMadeinthe80s 3 жыл бұрын
Anything for Jandy Watercolor replacements? Had two die in a year and warranty is taking too long.
@shannonseverin6522
@shannonseverin6522 Жыл бұрын
Did they ever respond about the Jandy light? I also had 2 die on me in 2 years and my pool company wants $1400 to replace it with the same crappy light or upgrade to a real LED bulb fixture for $2000 (which is what I thought I was getting the first time that they put that Jandy one in )
@frankortolano5886
@frankortolano5886 3 жыл бұрын
Can I change my Hayward lite to pentair without changing the housing
@_1ben
@_1ben 6 ай бұрын
maybe, hope that helps
@Gmoney1019
@Gmoney1019 3 жыл бұрын
The W and N marks on the lens refers to Wide or Narrow not to North or West side and is intended so you can direct the beam of light on a wide or narrow path depending on your pool needs.
@H00DRYCH
@H00DRYCH 7 ай бұрын
lmao yeah im like tf is this dude talking about North bro.
@Gmoney1019
@Gmoney1019 3 жыл бұрын
The replacement LED engine only works with the newer Intellibrite 5g version.
@AlejandroGonzalez-cs7sm
@AlejandroGonzalez-cs7sm 4 жыл бұрын
I just bought this, but neither my old board nor this one have the quick connect, it has 2 separate plugs (with blue jackets)
@Synnisster
@Synnisster 3 жыл бұрын
Ya man same, they need to post an updated video
@Cotronixco
@Cotronixco 4 жыл бұрын
Does Florida Sunseeker have an LED replacement for the Pentair Aqualumin halogen nicheless fixture?
@daredevilafk9491
@daredevilafk9491 4 жыл бұрын
So i just purchased 2 of these replacement boards and installed today. A couple small hurdles to get over. #1... there was no "quick Connect" on my lights nor the replacement board. So I had to match up the pos/neg, which was tricky because one board had TWO red wires vs a black and a red... #2... the spacer that you put on the ground wire nut was too short so when i tightened the screw down the board tilted way up. ( I ended up putting one of the old nuts that held the OLD board down on top of the ground nut and then put the spacer on and it worked great) #3.. I watched their video using the N=North methodology before I read the below comments on NARROW and WIDE.. My lights are on the side of the pool so I guess I should have used WIDE, but now don't want to take the rings off again if it compromises the new seals... #4.. i turn the lights on and it cycles through EVERY light and then ends up on a random color.. i choose another color and it cycles through all the colors again and a couple times ends up on the color I chose. I'll mess with the app more and see if starts to sync up. LONG WINDED.... but I hope this helps some of you DIY'ers
@bradanderson9524
@bradanderson9524 4 жыл бұрын
Can this pentair intellibrite replace the pentair aqualumin iii nicheless halogen fixture? I am trying to figure out if the size and depth are the same to fit in the existing area of my aqualumin. Please, advise. Thank you.
@markschoenfeld1083
@markschoenfeld1083 4 жыл бұрын
This looks great. I have an older model pool light, standard size. Can I replace the light with your LED?
@charlesbooth3799
@charlesbooth3799 4 жыл бұрын
The Pentair housing has what looks like a black ceramic filler in the center. My filler is almost flush with the wide surface (3/16" from the wide surface). The heat sinks cannot sit recessed to the point were I can attach the kit's screw to the grounding lug. How can I resolve this? Can I chip away some of the "filler"?
@zvettez
@zvettez 4 жыл бұрын
Charles Booth , any solution to your problem yet? I just received my light and having almost the same issue, even though I do have the so called filler sitting a bit lower on my Pentair it still too high up as to now allow the pool baron light to sit recessed to the point where I can attach the screws correctly and have the light level all the way around...any feedback would be much appreciated, thank you
@charlesbooth3799
@charlesbooth3799 4 жыл бұрын
Leo, I ended up calling the vendor and he said to remove the heat sinks. I asked "wouldn't that reduce the life span of the light?". He said "yes", and that was about it. I removed the heat sinks and still I had an 1/8" gap. I used a spacer on the ground post to gain clearance and to level the disk. It didn't get additional support from the other posts but seemed ridged enough. It's working. I'm hoping the 50,000 hour life span of the LED emitter will last at least half that long without the heat sinks. It might outlast me!
@zvettez
@zvettez 4 жыл бұрын
@@charlesbooth3799 Thank you for the fast reply, I'll see what I can figure out in the next couple of days, I think I might wait until Monday and call them to see if their answer is different. If not i'll try to rig it like you did and see how it comes out. Thanks again, really appreciate it!
@shannonseverin6522
@shannonseverin6522 Жыл бұрын
@@charlesbooth3799 Is your light still working without the heat sinks?
@shannonseverin6522
@shannonseverin6522 Жыл бұрын
@@charlesbooth3799 Is your light still working without the heat sinks?
@brez6541
@brez6541 4 жыл бұрын
I have 3 Pentair LEDs light in pool. 1 in spa and 2 in pool. Will your replacement match with the colors and mode with the existing Pentair lights. Thank you
@philipmendez8125
@philipmendez8125 4 жыл бұрын
How does your bulb effect the narrow or wide beam projection of the lense? That is why the lights are on the bottom to rotate the lense for either narrow or wide beam.
@Gmoney1019
@Gmoney1019 3 жыл бұрын
There isn’t any effects, with the replacement you just have a beam of light on all direction , the way around they have to fix the Narrow or Wide angles is they 18watts version or they 36 watts. Just less intensity but no way to change the angles.
@BigTruck
@BigTruck 4 жыл бұрын
Does it have a red white and blue color show?
@grassthief1280
@grassthief1280 4 жыл бұрын
Just recieved my replacement board from sunseeker had the GARBAGE PENTAIR #601000 series this lite sells for $800 I will never buy a pentair lite again ,BUT Jeff's board works well its brighter & more combo's compared to pentair way to go JEFF 👍🎯 , P.S if any change I will post to let you all know.
@OmarGonzalez-uj3ot
@OmarGonzalez-uj3ot 4 жыл бұрын
Is Forida Sunseeker still in business? I am interested in both the main pool and hot tub lights. Thx
@gabrielrivera1915
@gabrielrivera1915 4 жыл бұрын
Good video. Do they sell these kits for hayward lights?
@Gmoney1019
@Gmoney1019 3 жыл бұрын
Yes, they do
@Ed-pv6ke
@Ed-pv6ke 4 жыл бұрын
hello, got an older version of the pentair multi light (2). any kits to covert them too?
@sandrinegero2666
@sandrinegero2666 4 жыл бұрын
Well I bought this and the delivery will be sometimes this afternoon. I’m a girl and I’m doing this wish me luck lol!
@ACommenterOnYouTube
@ACommenterOnYouTube 4 жыл бұрын
Is the PENTAIR® AMERLITE NOT the same as this faulty Pentair Intellibrite..??
@joselacayo5944
@joselacayo5944 4 жыл бұрын
Are there any customer reviews? I am hopeful but would feel a little better reading testimonials.
@sandrinegero2666
@sandrinegero2666 4 жыл бұрын
Jose Lacayo I bought and installed it I’m a real person it’s awesome!
@maggiebrattoli383
@maggiebrattoli383 2 жыл бұрын
Read the other reviews. He doesn’t answer any comments. Beware.