Excess. Not access. 🙂

Удлинитель

Very nice vid, sir. Thank you. Idk if you care, but the word access should be spelled excess, I think. I got the point though. Thanks again!

😈 *Promo sm*

Codebooks are free online.

Maybe camera the lines before you start?

I was in need of this video … Nice job I’m a hands on type guy easy job

This video would have been superior without that loud crap playing in the background. There were so many excellent songs & tunes from 1971 & that era that would have improved this video. Anyway, I have a 1969 dodge d-200 camper special 3/4 ton truck that was iin a terrible accident that could have killed me almost 4 years ago, but after getting it fixed at a shop, it still runs & I still drive it even though it's slightly beat up after crashing down about 12 ' in the air coming down on highway 77 in south texas (driscoll) on sunday night, february 23, 2020. I was traveling from la feria/harlingen to corpus christi.

Try that on tile. You have flex in that acrylic. Just saying

Cut copper pipe 3.5in, when adding threaded tip it will be a total of 4in. You're welcome...

I DON'T SEE THE 2" VENT FOR THE TOILET .....

I hate mosin ... my love is lee anfield

Where can I buy the Moen thread on Tub Spout? The stores only sell slip on tub spouts.

Brief, but satisfying to watch Well done!

😁 Promo-SM

I'm thinking of doing this but I'm scared lol

Nice vid just wanted to se the cut too

How did you go from a light stain to a dark one after you applied a coat of finish?

ב''ה, looks pretty good for now but on a kitchen drain don't be stingy with that slope (beyond that necessary elbow) or you're in for years of snaking it, plus PVC can eventually sag a bit. Twice the length with that lowest slope (in fairness you've probably still got twice the angle of what the builders could do) and you'll really have problems later, especially with food grease and hot water from a dishwasher output.

Fail the inspection!

It's possible to leave the rad hose connected and not drain any coolant. Saves a ton of time and mess.

Your tie in to the waste is not correct. You are not supposed to tie in with a sanitary T. You need to use a Y with a 45 degree fitting so it will make a long turn sweep. The sanitary T fitting is to sharp of a turn for waste, and you are liable to get a clog

More illegal plumbing work, you cannot install a sanitary tee like that, San tees should only be vertical, also you rolled the shower up, that's called an s-trap 🤣🤣, these poor homeowners.

Hermosa camioneta, y son dignas de circularlas por las avenidas para admirarlas: Cuanto costaría una camioneta cómo la tulla? Gracias por compartir.

Would love contact info

No vent pipe?

you should of installed an all glue trap for your shower, and whats up with the up and over on the trap, where are the vents, you should of used a comby to tie into your existing

Thanks for sharing your skills. I look forward to doing my basement bathroom soon.

Oh bubba

What did you lub the drawer rails with ?

Very nice!

😜 ≋p≋r≋o≋m≋o≋s≋m

I point the handle out in front of my body when applying linseed oil. It's a more familiar motion.

I have a problem. My father in law gave me his 6.5 and already had the injector pump off so I don’t know where the original pump was in the timing. What do I do?

Doesn’t this hurt the value of the rifle?

Amazed the amount of people who do not realise the belt adjustor has a 1/2 inch sqaure drive hole in it so you can use a strong arm bar to take the tension off it

Very interesting video. I'm curious how dry the basement is compared to previous years and decades.

This seems very important lol I’m about to watch this video 100 times, idk even know where to start, what to take off first, almost feel mentally unable to remember where everything goes

Just did this again the 14th or 15th time this year i went to put the pump back in lined the pin up and the gear inside the motor literally spun a quarter turn before it took up the slack in the chain and stopped turning. Now the motor wont even spudder when i turn it over just sits there and cranks. Why they couldnt do things the right way and use a gear drive is just mind boggling and i dont wanna hear that the harmonics crack cranks ive seen 3 with gear drives exceed 600k miles what breaks cranks is bad fluid dampners and lazy bums that dont do maintenance. Kinda like who owned this truck im currently going through. Then i chase codes and have people tell me im just throwing parts at stuff after testing every single part and piece and finding it faulty. Honestly ive never seen such a great design get screwed up so so so badly by chevy its this motor that makes it so ill never ever own a new chevy cause of what they did to it. And this is from a guy who stands to inherit a part of a chevy dealership. ! That should tell you something about this motor and how bad our engineers screwed it up

Good technique.. I like to do two coats of fabulon polyurethane with a final coat of marine varnish as well for general wood work and stairs. You can make good time with the poly and it looks like you did 4 coats of varnish.

Thanks for wasting our time!

Could be better 😉

Maximo.0

If you stick towels under the pump you dont have to worry about the nuts falling under the pump when you put it back in just keep a magnet handy

No help at all.

Very clear instructions. Thank you!

Hey what color paint did you use?

OMG, we get it!!!! Line up the "alignment pin"

Nice project

How do you get those bottom two fuel lines disconnected? I have tried everything short of praying to Petro the God of fuel!