MiscDotGeek

Пікірлер

@lovelycollection100 6 күн бұрын

Maybe too loss in pass band filter. I Solve but have Lot carrier

@reasonsreasonably 9 күн бұрын

Thanks for this.

@billjobes1851 12 күн бұрын

I'm wondering why you take the time to separate the loop wires. I've always twisted the loops into a bifilar tight wrap up to the toroid and snipped the ends before inserting in the pcb holes. I'm careful to scrape the enamel off all wires near the toroid, to ensure a solid solder joint. Either way, the loop wires are joined electrically once soldered in place.

@MiscDotGeek 12 күн бұрын

It's been a few years since I made this video, but I think I was just following the directions closely. For the sake of demonstrating them. There's definitely lots of ways to do it. Your way is as valid as any. Thanks for the comment and watch!

@yoshimra 25 күн бұрын

I had one of those in 1973. You can use carbon rods to create a flame to braze.

@MikeLohrman 2 ай бұрын

I’m trying PETG for the first time on same glass bed. I tried the smooth side though. Got a couple good prints, but current print is a lot of tiny parts and they are not sticking well. Might try the textured side. I was afraid the textured side might stick too much.

@cbradiohamfan 4 ай бұрын

Hello I’m wanting to add a dds for multi band like yours what’s please can you tell me which resistor you remove before adding lpf to make it open up on all band Thankyou 73.

@MiscDotGeek 4 ай бұрын

Check my other videos about that, it's been a few years and I don't recall off the top of my head anymore. If you want multi-band though, get a uBITX. The BITX40 is built as a 200ohm radio internally, so if you're going to use multiple filters, like I did, you have to add transformers from 200ohm to 50ohm and back. Not a huge deal, but something to keep in mind that I did not know when I made this video.

@cbradiohamfan 4 ай бұрын

@@MiscDotGeekthank you I have a ubitx full hf and a bitx40 I have a dds vfo I have made for it it’s my test board for the DDS VFO 🎉 Thanks for your reply 73z.

@jakobh.4422 5 ай бұрын

Do you have a video using it and showing the different testscanrio you can do with it and how it can be handy.? (TinyVNA testboard for components etc) I know many people tends to use these VNAs for numerous other things, as you do have this phase_/time correlation between sockets and you can use them for numerous things if you know what your doing and how to proceed on testing approaches for various components..(I don't know the fundamentals, so Im looking for videos of it, but pretty much all the videos on YT, are people using them for their main popquiz like fx Antennas resonate area etc.)

@MiscDotGeek 5 ай бұрын

Hey there, thanks for the idea. It may happen in the future, but for now I don't have such a video or immediate plans :) Thanks also for the comment!

@kaiserollz 5 ай бұрын

Please help! I just got my QDX. But when I plugged in the usb it doesn't recognize it. How do I get it to show "QDX Transceiver". Very frustrated

@MiscDotGeek 5 ай бұрын

@@kaiserollz if you are frustrated, I would recommend that you step away from it and come back in a little bit. That's always the little thing I do first lol. Then if you still can't get it, check the manual about five more times. That's usually the next thing I do too. And then I go to the QRP labs groups.io page and beg for help. Good luck! You'll get it :-)

@ryanv7075 5 ай бұрын

Dude that cord is scary, best to replace it for sure

@ryanv7075 5 ай бұрын

I have a coworker who lost part of his house due to an electrical fire from a harbor freight cord running his smoker. Interestingly, I mentioned that to someone else today, but almost never do; what timing.

@MiscDotGeek 5 ай бұрын

No worries dude- definitely 86'd that thing. It went straight into the dump trailer :) Sorry to hear about your friend. Gotta be careful with extension cords, no doubt.

@bendunselman 5 ай бұрын

Did the hotglue detune the filter?

@MiscDotGeek 5 ай бұрын

@@bendunselman no not at all.

@peterarmitage5357 6 ай бұрын

There wasn't any problems with the original design, for sure it was designed to work with a little tinkering... but not a complete term down as you say!.. asher farhan is a far more accomplished electronic expert than you could ever be, you don't make sense in your explanations... don't give up your day time job... 😂

@TheGeocachingVlogger 6 ай бұрын

Put on my must do list.

@justinx590 6 ай бұрын

That looks so clean. Great find

@jimdurant1192 6 ай бұрын

How did you like your POTA activation? Thanks for the video. I am thinking about building a L network.

@MiscDotGeek 6 ай бұрын

Haven't used it for that but I'm sure it would work great 👍

@startobytes 6 ай бұрын

just made my own 3 Pole SSB Crystal filter, still need to figure out the right capacitors 150pF give me 1.9kHz. 3 Pole is simpler to find matching crystals. 73 de OE8GKE

@claudeanmankin1539 6 ай бұрын

@strawberrytart321 6 ай бұрын

GOT A MORTGAGE? PAY PROPERTY TAXES? iT'S NEVER YOURS....

@olig442 6 ай бұрын

well done

@MikeBenedict1 6 ай бұрын

Speaking for myself, I'd like to see all the renovations. I learn a great deal and gain inspiration from what others do and seeing how they do it.

@MiscDotGeek 6 ай бұрын

Thank you Mike!

@ronaldlindeman6136 6 ай бұрын

to much information.

@davidwilcox9110 6 ай бұрын

Ryan, I am so glad you found “your place”. Be careful and don’t put up a “temporary” antenna of any kind….. I have done that at two homes and each time life got in the way and the temporary antenna became a permanent antenna for quite a few years. They did work but were not the antenna I had dreamed of and planned for. If you are retired then maybe life won’t interfere. A drone view of your property might be helpful for designing where you might want to put up a pole to hold a loop or something like that. Find a neighbor or friend with a drone and give us some more information.

@MiscDotGeek 6 ай бұрын

Thank you, good sir! I do have satellite shots of the place I've been using for planning. There will certainly be a video about it :)

@MikeBenedict1 6 ай бұрын

At work we called anything intended to be temporary, "perma-temp" for self explanatory reasons.

@MiscDotGeek 6 ай бұрын

@@MikeBenedict1 That sounds about right :D

@caulktel 6 ай бұрын

Congratulations Ryan, I see lots of potential there, let us know how you progress over time.

@MiscDotGeek 6 ай бұрын

Thanks Joel! Much appreciated and yep lots of potential... and lots of work! Should be fun :)

@RechargeableLithium 6 ай бұрын

Congrats, Ryan! Post what makes you happy and we'll watch. 😀. 73

@MiscDotGeek 6 ай бұрын

Thanks, I appreciate the support!

@Wayde-VA3NCA 6 ай бұрын

Congrats! Looks like lots of room for antennas!

@MiscDotGeek 6 ай бұрын

Thanks, and for sure!!

@HowIsYourPc.123 7 ай бұрын

After how much time it gets overheated

@DanHidden 8 ай бұрын

I bought mine like 5 months ago and it was pretty nasty when i cleaned it

@AD_FISHING75 8 ай бұрын

Just subbed! Great vids!

@AD_FISHING75 8 ай бұрын

Just a little nose heavy. Keep up the good work!

@cubiconeandson5661 8 ай бұрын

Thanks

@JosephAnthonyJosefius 8 ай бұрын

I don't get any power out, yet I can receive just fine, any ideas?

@MiscDotGeek 8 ай бұрын

Check all your toroid windings and connections. Many times I've had to reheat them 2-3x to get a solid connection. Check the troubleshooting guide too. 73!

@ai5dd 8 ай бұрын

Thank you for this, I'll be assembling a 20 meter QCX this coming weekend. 72 de AI5DD

@Steve-GM0HUU 9 ай бұрын

Thanks for video.

@TheSillyshyguy 10 ай бұрын

Great to see you smiling Ryan!

@MiscDotGeek 10 ай бұрын

Thanks man! Good to be smiling again. Been a long road my friend...

@johnnywadd7960 10 ай бұрын

Hi Ryan, good afternoon, I'm getting ready as well to do some major welding.. stick and flux

@MiscDotGeek 10 ай бұрын

Nice! What's the project?

@JosephMorris-ln1dv 10 ай бұрын

How is it wited

@JosephMorris-ln1dv 10 ай бұрын

How is it wired

@MiscDotGeek 10 ай бұрын

Just a single winding into the primary, single winding coming out of the secondary. After more work I found the wire to be Aluminum, and I scrapped it. It produced only 20 amps or so.

@ThisisDD 10 ай бұрын

G10.

@N4GW 11 ай бұрын

Any AGC on the radio

@MiscDotGeek 11 ай бұрын

There is not

@N4GW 11 ай бұрын

@@MiscDotGeek sounds really good. I am getting ready to build an Airpal from InKits

@warplanner8852 11 ай бұрын

Ryan, {{{I AM YOUR LORD GOD, JEHOVAH, AND I COMMAND YOU TO CLEAN UP YOUR BENCH OR FACE THE FIRES OF PURGATORY FORTHWITH}}} Thanks, and see you in the tabernacle. *GOD*

@MiscDotGeek 11 ай бұрын

A clean bench is the sign of a quiet mind. :D

@blutadlerx Жыл бұрын

There is a special coating on the creality glass bed you are printing on, thats why it works so well :) idk if you would break the glass if you printed on the uncoated side though

@xXKisskerXx 5 ай бұрын

yes and no. the disappearing purple gluestick is a godsend. seriously. even with the coating on the glass to help - it can be terrible for some filaments.

@Thefreakyfreek Жыл бұрын

The only bad noises electronics can make is 50hz hum and fizzle pop noises The rest are just intresting

@jazzyjoe1848 Жыл бұрын

In my use case scenario, higher than usual temps did the trick. I've just tried orange PETG at 260 nozzle and 90 bed on a long part that stretches diagonally across the glass board. No warping and very good adhesion. Anything below warped.

@MiscDotGeek Жыл бұрын

Fantastic! I didn't try such high temperatures. I'm glad it worked for you though :)

@jazzyjoe1848 Жыл бұрын

@@MiscDotGeek Yes, was surprised myself :) I like how smooth and soft to the touch the material is compared to PLA. It's the kid toy material! :)

@MiscDotGeek Жыл бұрын

LOL @@jazzyjoe1848 fantastic! Thanks for the comments my friend.

@batica81 Жыл бұрын

Interesting experiment. I suspect the audio amplifier. You could connect the mixer output directly to computer soundcard input (through a capacitor) and try to see the spectrum in some SDR software like HDSDR.

@MiscDotGeek Жыл бұрын

You are right, it is definitely the audio amplifier. In the next video I will explain why I know this to be the case and will also attempt to remedy it.

@ei8ki Жыл бұрын

This will help you with calibration. kzbin.info/www/bejne/oYvdpYutbZ6Hi8U

@stephan5618 Жыл бұрын

Thanks for this! I'm starting to tinker in HF and this is a great example on how to achieve sth. pragmatically!

@Relayer1974 Жыл бұрын

What an awesome kit, thanks for sharing!

@mattpenrod7568 Жыл бұрын

Audio is super low - almost unable to be heard

@MiscDotGeek Жыл бұрын

Thanks for the comment. I didn't realize it until I compared it to another video I was watching. I'll fix that next time. 73!

@johnnywadd7960 Жыл бұрын

Ryan you need a SAD spectrum light for the depression.....

@Wayde-VA3NCA Жыл бұрын

Take care Ryan!

@johnnywadd7960 Жыл бұрын

What kind of welding do you use? Stick, MIG, TIG, Flux core? Happy holidays

@MiscDotGeek Жыл бұрын

This project was stick, but I just picked up a mig, tig, flux, arc welder. Going to set it up for mig specifically.

@techguy9023 Жыл бұрын

Did the onboard IRF 510 not have enough output? I have two that transmit but output is low. Started looking at the driver transistors

@MiscDotGeek Жыл бұрын

Great question! What it comes down to is that I had damaged the board quite a bit while experimenting and rather than try to rebuild, I went with a PA that I knew would be able to give more power and do it with less spurious emissions and with more reliability.

Ең жақсы KZbin

Пікірлер