Hi I was wondering if you could answer a quick question for me. Does the direction lever at the top wobble back and fourth as your turning the ratchet?
@jeremywyatt50Күн бұрын
Great video. I’m new to this wrench. Bought in yard sale with no manual… can you tell me best speed to use? Also what is the screw button for?
@OnTheWorkbench2 сағат бұрын
This tool was basically am impact driver that Kobalt changed a part to make into an impact wrench l, hence the screw mode. As for speeds it depends on if you are worried about tightening something too tight otherwise running it at max speed and feather the trigger.
@melissamarch78812 күн бұрын
I have the same model but prime bulb has 3 lines, how do I hook it back up properly
@OnTheWorkbench2 сағат бұрын
That does not sound like the correct primer.
@HiFiInsider3 күн бұрын
is this the same company as Astro AI products sold on Amazon?
@OnTheWorkbench2 сағат бұрын
I can't say for certain, but I think it's a safe guess that the two are unrelated.
@danroot844 күн бұрын
Great video. Valuable even a few years later. The only suggestion I have is to replace drive and blade belts during this 3-year as well. Already have the time invested so why not. Thank you!!
@drummin2dabeat5 күн бұрын
great video and glad you saved me the time of looking up the torque settings.
@user-sw4nt3gu3o6 күн бұрын
Дякую
@johnwallace5967 күн бұрын
Reading many of the comments sounds like many are using it for the every single nail they are driving....if you used it only for hard to reach areas where you cant swing a hammer or fit a framing nailer i am sure it would do a much better job. If it was meant to drive every single nail on your framing project, this little tool would reflect that in its cost.
@mr.5.048 күн бұрын
Wranglers are junk I got bought over 10 pairs an the Same thing has happened to all of them the crotch rips an the back pockets an belt loops break they are junk never buying them again
@jasonhaynes29528 күн бұрын
I've always had good luck heating a bolt with map gas, then immediately throwing cold water on it. Sometimes I'll do it a few times, then try breaking it free. Sometimes I'll do this then apply heat to the surrounding area (that the bolt threads into, not the bolt itself) and it works well. Of course, sometimes you can't use heat because of wires, seals, etc so this might do the trick. Or even heat it with map gas, then spray this on it.
@antilaw99119 күн бұрын
I have full complete set of USA Masterforce wrenches. SAE/Metric. Still brand new in they're holders. Bought few years back like you show on clearance display. Very nice wrenches and proud to own them. I'll throw a video up! 👍
@WillBratt9 күн бұрын
Super helpful video! Thanks so much for posting!
@georgecurtis646311 күн бұрын
Long ago we used to use r12.
@bradforward85011 күн бұрын
Thing works great! Until the nozzles plug. And try and replace them with original parts. Aint happening. NEVER buy one of these from Kobalt if they aren't going to supply the replacement parts. Things pretty much worthless now.
@ShakeNBaked12 күн бұрын
Trying to figure out how to put a new cable in mine. Can't find a manual either
@SamiDurm12 күн бұрын
Too much water, makes a mess. I just put a wet sponge next to the blade, to keep it wet
@mbabble213 күн бұрын
can you provide the step by step on programming? pretty please???
@justmark5615 күн бұрын
My lower handle has cracked on mine 2 × now. I bought a replacement $155. on Amazon and that has cracked as well. Both had to be welded. I'm very aggregated at this Toro.
@ScottSavitt-c3x19 күн бұрын
Thank you for posting this video. I was able to order the kit and complete the job with confidence. Really appreciate your help. Keep up the great work.
@FamilytripsNevents20 күн бұрын
Thanks you for the video. Might be a good time to replace that plastic OEM T fitting to one made of metal. They break easy after some years of use. Looks like you have the original plastic. It's on the left side under front cover. They were on Ebay with the two bigger hoses for $31 shipped.
@MarzNet25622 күн бұрын
Use a milwaukee m12 battery...or any 12V power tool battery to power the unit for bench testing.
@Snausages3222 күн бұрын
Super helpful! THANK YOU!
@PaganWizard24 күн бұрын
You showed one of the nails blowing out the side of one of the boards you used for testing. I have learned that, this almost always happens when the nail gun is parallel to the wood grain. If you turn the lumber, or nail gun, whichever is easiest for you, so that the nail gun is perpendicular to the wood grain, nail blowout is extremely rare.
@stevekovacs625026 күн бұрын
I anticipated the weak link at the handle with mine and put a pair of hose clamps on either side in order to take the stress off that area.
@ljalpena355228 күн бұрын
Mine only blows for 10 second at a time, then stops for 30 seconds then runs 10 seconds.
@arthurshagnasty506828 күн бұрын
When you connect them is a dominant one , the left or the right channel?
@arthurshagnasty506828 күн бұрын
Now that you connect them to And connect them to your phone.How far can you separate them before you lose one?
@arthurshagnasty506828 күн бұрын
When you connect to those two units did it split Left channel and right channel? A full stereo mode? Get it just stay in mono and just have a extended mono range?
@luiip18628 күн бұрын
I have a po455 code but no visual leaking after smoke machine test only a faulty pressure sensor and a software update any idea?
@mienqchau28 күн бұрын
Is there shorter barrel?
@JuniusJones29 күн бұрын
I returned this yesterday lol
@NHseacoast29 күн бұрын
Harbor freight looks orange good reviews
@NGMonocromАй бұрын
4/20.... How ironic. At least it's easy to remember. I was just about to standardize on Kobalt's 24v. battery platform. I guess I technically could still do that. I'm just imagining some poor schumk who did that very thing back in 2019, bought up a bunch of Kobalt tools. Using them for DIY projects, and when that last older Kobalt battery gives out.... He's going to be stuck with a bunch of very expensive paper-weights shaped like tools. Just outside of the warranty coverage. So yeah, there's still Craftsman as another budget alternative right along side with Kobalt. Sold right next to it at Lowe's. You got Ryobi over at Home Depot that at least put a massive amount of care and effort into making sure all their lithium-ion battery packs actually are backwards compatible with their older models. (Though honestly under-powered compared to similar ones from Kobalt.) Going with Ryobi's sister brand RIDGID would fix that problem. But at more cost involved. Not a Tradesman, not a Contractor; just want some quality tools that will last! Screw it. Nowadays you want quality, apparently you have to buy Pro-grade tools. Such as Milwaukee, Mikita, or the higher-end DeWALT models; and pay through every orifice. Not just the nose.
@btbd2785Ай бұрын
So much for demonstrating what the airshield nozzel does
@newtea2458Ай бұрын
Thanks!
@virgilwalkerАй бұрын
HOW DO YOU ADJUST THE WRENCH FOR RECALIBRATION, OPEN THE BOTTOM OF THE WRENCH. HOW THE HELL DO YOU TURN THAT NUT. THIS CANT BE RECALIBRATED.
@tylowe78Ай бұрын
That lock tool does not work. I may have to use an impact wrench. That bolt is so hard to get off
@roberthibbs9988Ай бұрын
Any idea where I can find instructions on replacing the auger cable on this machine?
@ShakeNBaked3 күн бұрын
Find anything?
@balancenutritionwellnessАй бұрын
I thought it was a good idea, but the base they provide to cover the motor doesn’t fit like any video I’ve seen so I’ll be returning mine
@billpigue3690Ай бұрын
Thanks for the information on the handle replacement,,one thing I improvised was instead of prying the handle over the catch, I found it easier to place a feeler gauge over the catch and just push down,,,,, thank you for the video,,it helped a lot
@joelrazoofficial1312Ай бұрын
did you flush after using it or just leave it in there because i used it on my truck and it worked but i didn't know if i had to flush it out after a while i hace half a year and no leaks
@glassamerica1Ай бұрын
you connect the new strut to the hub first on these because they dont have studs up top. there is a hex spinner under the top of the strut cap. use a sep mini jack un the hub to align the bolts for both hub and sway bar! If the top 3 bolts are not centered then you will probably need an alignment. usually a 50/50 chance you dont have too.
@rich4244Ай бұрын
It took 20 years but got the joke now on married with children. "that will fix .. the little red wagion.
@stan_seniorАй бұрын
Is there a carrying case available for this saw?
@idjc2621Ай бұрын
Relieve the pressure!!! Valve is by the fuel filter on the 3.2xc90. It helps.
@viveviveka2651Ай бұрын
There are two versions now. One has a fan - the "Pro." It also has electronic ignition.
@LakeErieBirdsАй бұрын
EXACTLY the how-to I needed for my MCT washer! Thank you!
@waiting4aliensАй бұрын
Good if you use a caliper for the bolt head and the inside measurement.
@ctll626Ай бұрын
Dude spent 5 min talking about tools and cleaning supplies, yeah doesn't show how to remove the top, the agitator and the basket/tub. Skipped the how to part of a how to video 😂