Brooo could you give me your mail ID so icould clear my doubt

try making dexibel plus dba, dbc and max buttons

Can I ask why mine is always zero reading its my second sensor purchased but still same already connected to 5V of arduino mega

Hello! in this project can i control the lights in the house using the mobile phone even if i am far away?

I want to try this but can’t project schematics or source code on website

I think, the + for measurement should be taken from another place. OUT + is a exit from module. When you charge via usb port then on this OUT+ -> 4.2V. I can be wrong, but for Voltage + should be connected to battery +. I tested something on my desktop. 18650 has 3.60V and going up. On OUT+ -> 4.2V. When 18650 gets 99.99% charge and disconnect charger from usb port, then basically voltage on B+ and OUT+ is almost the same. I can be wrong but I work on small project which will be powered by one cell 18650. Amateur nrf24 module shooting clay machine small system ;)

why does the userlog wont update? can you please reply because the deadline of our thesis is tom!

what is the difference with and without the antenna??

I had a doubt if i run ngrok and generate url will it work for all time or whenever i have to watch live streaming does i have again to generate url always?

Ok where is the code

Anyone can’t try to do any project published by this author because you can’t receive any help from this author & you can’t fulfill any project successfully without any help from the author. I have tried to do one project published by this author but not successful because I can’t get any help from her. Your rupees will be lost without any help. My project was smart notice board with ESP8266 and Max 7219 LED display.

I was try but it is not send any sms or phone calls only buzzer sounding

Brother may I ask why are you giving a wrong code? This is my second time landed on you channel. Last time RF ID its takes weeks I crack your syntax it gives me a hard time. Can you give me the correct code this time please?

maturnuwun

Hi i really love your videos, what wind vane sensor you can suggest to integrate with that anemometer?

I want to move the servo motor at an angle of 60° - 80° and display it on the LCD via blynk monitoring. can you help me please?

If you don’t answer any comments then please out the comments section. I have asked you one question since three days ago but you don’t answer it. Your pronunciation is not good to understand it. You want to produce some stylish pronunciation which is not good to hear it. Please answer my query.

Great ✌️

Please answer my query at your earliest.

Madam job code upload karte hu tob yeh fault show karte hai. Please advise me how to solve? Empty character constant. curMessage [0] = newMessage [0] = ‘’;

where did you simulate your circuit at 2:00 ? tinkercad? wokwi?

Thank you for this project. It is very interesting and useful to me. I have a question: Is it possible to add an OLED screen to the project? I hope you can support me with a solution for this. Thank's!!!

What is the purpose of the voltage divider and what if i don't make a voltage divider

Bro I want this fall detection in smart watch with iot technology plz make video for that

JFYI Without clk and cs resistors and extra capacity next to max7219 chips you can experience glitches or garbage on display over time.

Sir ji, dual side solar tracker using arduino uno and LDR project banado na jo working ho

Your code is not working the oled is not even turning on Is there something missing please let me know there was some minor changes in the code which I have done by seeing your video in slowmo

Nice

👍✌️Regularly watching your vedios

► IoT Smart Notice Board with MAX7219 Dot Matrix Display ESP8266 NodeMCU & Blynk App ► Circuit Diagram, Source code, & Guide: iotprojectsideas.com/iot-smart-notice-board-with-max7219-esp8266-blynk/

Hello, how to run power down mode in both Arduino and RC522? By bringing the card close to the RC522 module and using the interrupt mode in both modules, the system is started and after running, it goes into power down mode twice to extend the battery life. If this is not the case, the battery will run out in two weeks. set_sleep_mode(SLEEP_MODE_PWR_DOWN); in arduino and mfrc522.PCD_WriteRegister(MFRC522::CommandReg, 0x10); in rc522

► IoT Water Quality Monitoring with TDS Sensor & ESP32 iotprojectsideas.com/iot-water-quality-monitoring-with-tds-sensor-esp32/ ► Water Quality Monitoring using TDS Sensor & Arduino iotprojectsideas.com/water-quality-monitoring-using-tds-sensor-arduino/

Nice 👍

► IoT Smoke & Gas Detector using ESP8266 & Blynk 2.0 Download the Circuit Diagram, Source code, and guide from here: iotprojectsideas.com/iot-smoke-gas-detector-using-esp8266-blynk/

I'm just looking for it, but I have a question: can the buttons be removed? I'm only interested in the smoke sensor (I'm very new), thank you.

No political circus against the CaesarKing I, then the Philippines Senate, Congress and Judiciary of their national functions shall be reactivated as programmed event on January first year 2025. No sabotage to create paralleled effect. Theres a National government officials of the Philippines campaign period next year. Understood. I had too much headache and irritation endured for such which sometimes go beyond their limits and toe the line boiling my rage from discovered connivance and sandwiching schemed moves. Comply. The CaesarKing I ordered. Let it be

so its a product manufacturing fault

Battery voltage? And link to buy

Good day kind Sir, what's the thing/component on the top of LCD? or like how would you call it?

legit or scam indian staff

I just stumbled upon this piece about IoT, and it really opened my eyes. The insights shared are thought-provoking and genuinely refreshing. If you're curious about IoT, this is a must read in GAO RFID Inc -there's a wealth of information here that could reshape your understanding.

i want to buy this

Very Good!

► Fingerprint Door Lock Security Systems Using Arduino & LCD ► Circuit Diagram, Source code, & Guide: iotprojectsideas.com/fingerprint-door-lock-security-systems-using-arduino-lcd/

Thank you so much for this amazing video! Could you help me with something unrelated: My OKX wallet holds some USDT, and I have the seed phrase. (alarm fetch churn bridge exercise tape speak race clerk couch crater letter). Could you explain how to move them to Binance?

► IoT based Anemometer using ESP8266 & Arduino IoT Cloud ► Download Circuit Diagram, Source code, and guide from here: ► iotprojectsideas.com/iot-based-anemometer-using-esp8266-arduino-iot-cloud/ *************************************** #iotanemometer #iotwindspeedmeter #windspeedmeter #oleddisplay #npnpulseoutput #anemometer #iotprojects #windspeed

❤❤❤

❤❤❤❤

► Interfacing ZMCT103C CT Sensor with Arduino ► iotprojectsideas.com/interfacing-zmct103c-current-sensor-with-arduino/ *************************************** #ctsensor #zmct103c #currentmonitor #arduino #irms #voltage #energymonitor #accurrent

connects to router succesfully but when typed that address in pc or mobile its not workinbg