Ehrin Anthony

Пікірлер

@abrahamsotelo95 2 ай бұрын

Great video. I just got a roland dual zone trigger with this module. I do a lot of rimshots and I'm getting the rim sound only and not both. Is it possible to get both sounds at the same time?

@ehrinlanthony 2 ай бұрын

@abrahamsotelo6188 Unfortunately, I do not believe that is possible. It's one or the other.

@AlanBaker-l8k 4 ай бұрын

What have you set your output gain to? +2 or +4dbs?

@ehrinlanthony 4 ай бұрын

I keep it at 0db. Never had anyone tell me they needed more or less so I haven't messed with it. If your mixer needs more input, you can adjust it higher.

@marksadventures3889 5 ай бұрын

cool;

@CharlesGibault 5 ай бұрын

Thanks a lot for this, Managed to get a lot more out of my Ghost piezo (on solid body). Suggest you give a try to Gibson 1969 J45 (Fishman) IR profile. This is what got me the best result, even better than the Guild

@superglassbucks6356 5 ай бұрын

I’m going to try this and add it to my favorite preset as a snapshot. I have a EBMM Majesty with a piezo. I’ll let you know how it goes

@AlanBaker-l8k 6 ай бұрын

Great video first time using tm2 and roland triggers

@astrofreq Жыл бұрын

So is there no tone knob on the guitars with acoustic saddles?

@ehrinlanthony Жыл бұрын

Normally they have a tone knob, but I never use it so I had it removed and replaced with piezo volume.

@TewwaTekle-1 Жыл бұрын

Can you tell us where you got that two pipe clamps? 🙏🏽

@ehrinlanthony Жыл бұрын

www.sweetwater.com/store/detail/ADP20--pearl-adp-20-clamp

@TewwaTekle-1 Жыл бұрын

@@ehrinlanthony thank you 🙏🏽

@digoutyourMUSEsoul Жыл бұрын

Sounds really good.

@sweeptheleg6852 2 жыл бұрын

This is the best video on calibrating a TM-2 with triggers/pads that I've come across so far. Most videos just tell us what each setting is for. You actually showed it in real time while striking the pad. The way you explained the sensitivity setting with the velocity going up to VEL////127 made it make more sense. Thanks

@jonasjpeg 2 жыл бұрын

Is it possible to assign the sounds/pads to separate outputs? My kick and snare for example needs different channels to be mixed properly. Can’t find this feature anywhere!

@ehrinlanthony 2 жыл бұрын

The TM2 only has stereo outs. You can assign sounds to one or the other by panning hard left and right. I.e., pan your kick hard left and snare hard right. They'll come out of two separate outputs.

@35milesoflead 2 жыл бұрын

Nice work there chap. Clean and no nonsense. I was looking at gimp for my overlays and you have shown me some nice ideas. Definitely feel better about using Gimp for this kind of work.

@akashkishore2076 2 жыл бұрын

Finally!!!!!!!!!!thanks man

@DaveyDjanDrums 2 жыл бұрын

What mixer do you have?

@ehrinlanthony 2 жыл бұрын

Depending on the gig I use two different setups. For full in-ears, I use a Behringer X32 Rack. When we're using backline or have floor wedges, I run the click channel into a Behringer MicroMON MA400 so I can have click in my ears without it going to front of house.

@ehrinlanthony 2 жыл бұрын

kzbin.info/www/bejne/Z2m5qKObf9mbd6M watch at 6:54 to see how I connect the MA400 to the TM-2

@TheDrumms93 2 жыл бұрын

Hey Ehrin, great video. A question. Is there a possibility that after playing a backing track, the next one will be loaded directly, which I then just have to start? Or can you get to the next song by hitting the pad? Or do I always have to press my hand on the tm2 to go to the next song? Greetings from Germany

@ehrinlanthony 2 жыл бұрын

I have not found a way to change the backing track without pushing the plus and minus buttons to navigate to a different patch.

@agileconsultant25 2 жыл бұрын

Thanks so much!! been looking at ways to trigger backing tracks and already had TM2. Really awesome video on how to set that up

@JimCreatureCornelissen 2 жыл бұрын

Very helpful!

@paulhunter2001 2 жыл бұрын

Hi there what programme do you use to link your backing track and click track thanks

@ehrinlanthony 2 жыл бұрын

I use Reaper. I create the backing track and pan everything to the right. Then I create a "drum" track that is just a stick click and pan that to the left. Render the track out at 16 bit, 44.1khz and load it on to the SD card. Let me know if this helps.

@libertyspikes666 3 жыл бұрын

Do you create a different kit for every song in your set? I want to do something like this where I have 1 pad to launch backing tracks with click panned out R L and then another pad with one shot samples.