Would you sell It?

Don’t see how these transmissions hold up as good as they do the way they slam into gears you’d think it would rip them to pieces

Looking forward to this project !

At our shop in Indiana I have a 4955 transmission torn down. I have a question was there thrust washers on both sides of the last gear you put in the output planetary in the center of the transmission? The one you replaced the bushings in at 8:40. Appreciate it thank you from Indiana

Good day I'm from Ukraine Recently bought a John Deere 4650, after repairing the gearbox, problems began On 3, 4, 6, 8, 10, 12, 14 forward gears it seems like something is slowing down, it is very difficult to drive and 1, 2, 3 reverse gear is almost impossible to drive Could you suggest something, did you have something similar? I will be very gratefu

who the f buys JD anymore

Job well done there

Hi, does the shaft slide out?

Any progress on this engine. Would love to hear it?

What a beaut!

How do you get the pto gear & clutch out. Have tractor split rebuilding front half. Got the cherry picker on the gear with the bar to lift. Pull it forward and it hits on bottom of housing. Supposed to pull lift and tilt right out by manual. If you had any issues w that. I’ve done one before and it pulled right out

I didn't catch the part where you adjusted the output shaft preload..🤔 Loose bearings on the output shaft cause failures such as you experienced.. FYI, the output shaft supports the tail end of the planetary carrier and also keeps the sun gears centered in the rear planetary gears.. If it becomes loose in the bearings, it becomes a free-for-all inside the planetary pack!! Also, the preload on the output shaft bearings has to be checked and adjusted with the planetary removed..

Good job done...sombidy told me the claas ellios is a same or deutz dressed up as a claas or has deutz/same components... does that sound right ??

Great job on the teardown and diagnosis! Very well done young man! Great rebuild as well. Thanks for sharing this with us, it helps many out here doing the same thing. Take care, God bless!

Hello. Did you change the pto clutch too. It may be slipping on my 4055. Be a big enough job to do?

≋p≋r≋o≋m≋o≋s≋m 🌟

We have a 4960 in our workshop, and the big difficulty are the parts because this tractor does not have many in Brazil. If you are available to give us some tips it would be fantastic as soon as the pieces are obtained. Great Job!!! Congratulations!!

Absolutely superb. Love it. Longer videos please!!

Are parts still easily available for these ? Obviously its old.

Nice,on the farm where my dad worked in Wiltshire they had a 2WD 4640 in the late seventies and early eighties. 👍

Lovely old thing. Shame you didn’t video the engine swap mate……….

Loving the tunes mate good taste

Good morning! I farmer from Ukraine 🇺🇦 Have a John Deere tractor 4650. How much rebilling transmission? My transmission failed.... Moved just back,

Is the new e23 a Funk Transmission?

Hello there i wondering where about are you base? cause I got a friend with a 4050 with a power shift problem if you be interested

Have you had any experience with brake issues on the JD 3420 telehandler?

To me,this type of knowledge and expertise needs to be passed on.. It's just amazing what the human mind can learn..Great video. 👍💯👍💯

Hello, a few months ago I bought a JD4955 powershift transmission. Before I bought it, I tested it - everything was fine, except some little jumps when shifting gears. I have not driven too much - just about 80 hours - attaching a plough, testing the plough, working with a trailer and so. Afew days ago I started to prepare the tractor for new mulcher - to put defense from trees bellow the gears. Tractor worked fine. In the next morning, when I started the engine and switch to reverse, the tractor started driven ahead. I turned it off, restart the engine and again - put on reverse it was going front. At the same time the front gears - work fine. After I disconnect the rods and manually tried to switch to reverse (from the cover of transm valve). Tractor still going only forward. After a few more tries - I discovered that when switch to front (1-15) the tractor starts moving, but when push the brake, it stops (with engine still running). Then when I switch to contact, I hear the alarm and the arrow for front travel on the left of the screen is on. Then I decided that it coud be broken spring pin (holding forward/reverse valve), but no - I dismounted and the valve is OK. Could you please give an idea how to continue to diagnose the problem and what could be the most probable reason for this problem? [email protected]

бад видео 1.40 зашто ниси рекао колики треба да буду притисци на контролним тачкама и где су контролне тачке? правите видео и не разумете шта радите? kao na primer cene opravke sa koje je strane auspuh i slicno --pa zato imas od takvih bolida 900 unit - koji su te pozitivno ocenili VIDEO cilj- treba da bude TUTORIJAL a ne abortus video za izdrkavanje pameti

Wow that was an interesting job. Parts bill alone must have been eye watering never mind labour 😮. Job well done

Massive Job

Well done

Fair work well done I wouldn’t like to have to face that

Superb job boss!

Hi Darren, one of my injectors is not coming out it only comes up about 20mm and then stops like its hitting something, any ideas?

Unde este electrovalva la 4wd?

Can you give more picture and mor info how to dismountling transmision jd 4755. Regards from Romania. You are using some special tools for dismountlung

Îmi puteți spune unde este electrovalva la un4455?

What a cracking job you made, your skills are second to none, 👌👌👌👌

Excellent job mate!

He’ll sum job on there mate good job done!!

Brilliant. I’ve never seen such a collection. Your grandad must be quite a chap. I think I’m right in saying your in Cornwall so a bit far for me. Could you video a bit of the auction perhaps?

I LOVE YOUR WORK 💪💪💪🇺🇸🇺🇸🇺🇸JOHN DEERE THE BEST

How much this repaire is? May be good used tractor is more cheap?

Great video! Literally just came from checking my engine with the same issue. Also have the oil leak. Hopefully this sorts it out. Where’d you get the replacement seals and copper washers?

sheesh mate you've got to tell us what that jd box of goodies was worth!

Pleased to see your still doing videos. Sorry to hear about that thumb. Sounds painful. I sprayed a jet ski a couple of years ago. It was just about passable 🤔😆. Glad to hear you’re going to do some farming videos as well. Looking forward to seeing them.

Another interesting video squire!

Interesting stuff squire. Will you repair or scrap the old boom?

What do you use to seal between the input planetary housing and transmission case ? It doesn’t look like there was any sealant there when it came apart.