Good, basic video. Best part is emphasizing NOT TO ROTATE RF connectors. Lots of cringe factor on YT watching students and pros alike spinning connectors onto VNA ports directly.

Thanks for the video.

Totally confused ! I just bought an SVA1032X (same SA as this) based partially on this review - thanks ! There is a setting in the "BW" menu called "Average Type" with no useable explanation of what "averaging" operation in the device it controls. The manual says, "When trace average is on, the average type is shown on the left side of the display" however the average type selected here is ALWAYS shown on the left side of the display no matter what is turned on and off - anywhere. And there's no "Average" setting IN the BW menu, just this "Average Type" setting. What is this setting actually DOING ? Which average function does it pertain to ? I've been trying to get the simplest answers from Siglent support here in the US but they are absolutely USELESS !! There doesn't appear to be any other source of support for Siglent questions and problems. I'm almost beginning to wish I'd never heard of Siglent for confusion like this !

I have no idea why KZbin recommended this video to me but I think this is a spectacular device. Well done, Siglent! I wish i knew what this device is for.

Cool to see and all, but I doubt anyone watching these videos can even come close to affording these things 😂 window shopping I suppose

Nice machine 👍

1- The cost to performance ratio is excessive in comparison to Keysight even though these are less expensive. And so, it is a waste of valuable funds for serious users. 2- It is excessively priced for the hobbyist. 3- It is aimed for perhaps the persuadable markets such as academia who are comparing to Keysight on the criteria of basic specs and appearance. In which case it may appear as a good deal. Make no mistake. These units should cost less than 10% that of products its trying to mimic in core specs and appearance. Not 50-75%. It may look like a PNA-X, but its a far cry from the tens of millions of dollars worth of ongoing research that go into the serious instruments by the likes of Keysight and R&S. The solution is simple. Dont buy 2-4 of these for your lab. Instead, maximize the value/dollar and buy 1-2 Keysight instruments.

Well done SIGLENT ... Great development ... Keep going for higher performance , higher precision , higher quality production ...

Does the SDG2000X series ALSO have "Square max freq = Sine max freq" ? You never said ...

Why didn’t you show the buttons and knobs you were using to adjust :/

Nice but I think I would have preferred it to be done slightly differently, by having 3 identical channels of 30V/5A, all of which could be paralleled or put in series, to allow you to do up to 30V@15A or 90V@5A in those modes, ideally by choosing how many channels to put in parallel/series, so if you only need to parallel 2 you can, or if you need more, you could do 3. having a fourth channel is nice too for 3.3V/5V system use. I have an old Korad 3 channel unit on my bench (as seen in many of my videos), would be nice to replace it with something better of similar physical size, such as this new Siglent unit.

It looks very good, I would love to play with it, maybe it would work better than my rigol dp832

She is very beautiful!!! I have the SPD1305X and I am happy with it, but it still has some problems that have not been resolved, such as when activating the OCP the watts are not correct on the screen. They should make a new firmware for us please. Thank you! 🤗

It's great, I've been using the SPD3303X-E model for 5 years and I'm satisfied.👍👌

Very nice. But to be honest I would preffer PSU in white color 🙂

Focus, focus, focus.

Amazing video, my respect, Could you tell me if we need tracking generator? What is her functuon..thanks

very nice, I bet I cannot afford one though !

This is INSANE

I love my Siglent scope but one thing that upsetting is, we wanted to use the device in a lab which we have no control over the wifi SSID and password and Siglent doesnt allow us to use special characters or not even the wifi guest network which has no password, we get the error password at least must be 8 letters long... No password has to be right, and in this case its empty however system doesnt accept it. So sad after buying the dongle and the Wifi license. I think your next update, shall you have any, has to definetly fix this. I dont have wifi connection issues with any of my devices including embedded linux systems so I am assuming it has something to do with your UI.

I like this scope based on what I see in the video. Only thing I'd change is to make it USB powered. How much current does it draw at low voltage levels?

Thats a cute engineer right there, although im a bit concerned about him touhing the power supply there, I hope you dicharge them before hand

Thanks. I do not find the range of sensitivity settings on the channel inputs. I looked at Siglents homepage as well. Can I somehow get this information?

Why was the 100mhz version discontinued?

WHY did you compare 100mV in 8-bit against 1V in 12-bit? We know that you tried to cheat, this is BAD.

I have a ssa3021x+, it's the same processing, thanks for the help..

How do you manage the cable lengths correction, as a calibration procedure? If no correction available, do we need to use identical length/loss cables on the two channels paths ?

I am trying to find some info on this, espectially direction finding of interfering sources. The bird signal hawk has the Angle of Arrival which it draws on the map. Can this also be done on this model ? also some info on the indoor map capabilities

Hi @SiglentVideo. Is it correct to connect SDG to the DUT via a T-piece and then to the oscilloscope? This would allow second output of the SDG to be used for other purpose. This configuration will also tell the oscilloscope the real value of the voltage on the input of a DUT. The presented connection method actually separates what DUT actually sees from what oscilloscope is presented by a separate channel.

One a piece of trash

Its a nice scope, but has quite some bugs! It seems to me, that the customers are here the beta testers?

Great scope! Selling from us like hotcakes!

Does this not work below 200mV/d ? It doesn't seem to on my SDS1104x-E. When i go from 200mV/d to 100mV/d it resets the offset.

The Spectrum Monitor (waterfall) on my unit stopped working. The button is inactive. Is there a way to reset it? I did the system restore to factory settings.

Is it possible to combine these two devices to image the amplitude-frequency characteristics of the system on an oscilloscope? I would like the generator and the oscilloscope to form a wobuloscope, is it possible?

WHY it's not isolated? It should have the USB bus power, not the IEC socket...

Solid response to competitors. That said, I would have liked a slimmer device. But it boots relatively quick and in videos the UI appears to be quite responsive.

TRY NARRATION and drop the crap music

great

Siglent Hi, can you make the oscilloscope outputs programmable. For example, we have a sine signal from peak to peak 10 volts, to program when the sine goes from 1 to 2 volts then the output let it turn on. This is the simplest example, but to be able to program absolutely any even complex tasks that you want, and get the desired signal at the output, which can be monitored by the same oscilloscope. Siglent привет, а вы можете сделать выходы осциллографа программируемыми. Например имеем синус сигнал от пика до пика 10 вольт, чтобы запрограммировать когда синус идёт от 1 до 2 вольт то выход пусть включается. Это простейший пример, но чтобы можно было программировать абсолютно любые даже сложные задачи, какие только захочешь, и получать на выходе нужный сигнал, который можно проконтролировать этим же осциллографом.

How much is it?

This would go very nicely in my lab...

Awesome

Siglent has amazing 12-bit scopes, which we love selling at Saelig! Great presentation!

For those wondering - it costs about $22,000

Thanks

Thanks for the tip about the flimsy cable! Quite useless..

If you put the spectrum analyzer on zero span you can get the same oscilloscope display ;-)