9 ай бұрын
10 ай бұрын
Жыл бұрын
Пікірлер
@HvacDaddio Ай бұрын
I saw the benefit when you one handed the bend while holding the roll. Ratchet benders like Hilmor would require both your hands.
@chrisb1899 2 ай бұрын
There are 3 Phillips head screws at the top of the panel then I believe the panel sits on 2 supporting " lugs" . Lift up on the panel and pull straight out.
@coverdown6544 2 ай бұрын
How to remove the bottom panel? Your video only shows it off at the start and then it's on when your all done. I see the two bolts on each side. I pull up and bottom is detached, but can't get the top to come off.
@marconantel7735 2 ай бұрын
How was it to finish up? We are looking for a similar solution that allows for easy access to the flare fittings.
@chrisb1899 2 ай бұрын
It was simple and clean. The box cover itself is held by a few plastic tabs that are needed a small reciprocal saw to cut out. A box knife didn't do as well as I hoped. But it left a LOT of room for flare fittings and pushing lineset back. Plus condensate line went in real smooth also.
@marconantel7735 2 ай бұрын
@@chrisb1899 thank you for the feedback!
@markthomas2352 2 ай бұрын
My igniter just went out for the 2nd time in the 4 years of having my 48” NXR entree oven. 😢
@chrisb1899 2 ай бұрын
This video was actually my 2nd time changing it. Thankfully it's cheap and easy for the most part.
@ARIASPHIL123 3 ай бұрын
Condensation line needs to be PVC pipe or can I use drain line the come with it
@chrisb1899 2 ай бұрын
The indoor unit comes with a drain line that I push down into the larger PVC I installed.
@ARIASPHIL123 3 ай бұрын
Rough in box need to be install by Code ?
@SardarJabo 3 ай бұрын
Will done great job
@chrisb1899 2 ай бұрын
Thanks. It was a fun one !
@mariagensheimer4817 4 ай бұрын
How did you remove the panel on the bottom
@chrisb1899 4 ай бұрын
There are 3 screws holding the panel in . I believe the panel also sat on a small " lip" to hold it up while you remove the screws.
@amargopaul3082 5 ай бұрын
Hi nice info. I have a 32 in Nxr and the stove is horrible. It would keep clicking on every burner. Any info on how to fix this ?
@chrisb1899 5 ай бұрын
The clicking sounds usually indicates the burner flame isn't being sensed so it will click or spark until a flame is reached. With a small SOS pad or sand paper , you can clean those flame sensors. They are under each burner cap.
@chrisb1899 5 ай бұрын
Yes, the gas valve opens for a small amount of time but doesn't ignite.
@pattyrountree3528 5 ай бұрын
When the igniter went out, did the oven just smell like gas and not get hot? When on?
@fashngrl01 3 ай бұрын
Mine smelled like gas, and would get hot but not at the temperature I set it at. I believe mine is the igniter.
@prestigemechanical3600 5 ай бұрын
That’s crazy. Usually I can do a single hose 3/4 BluVac 5 meter long hose and have it down in 3-5 minutes on a new system max
@simondetroit 5 ай бұрын
Thank You for the video….. it worked for me! I used part number x00389ar6x ERP IG9998 Universal gas range SMD from Amazon
@justwork_hvac 7 ай бұрын
Awesome brother thanks for sharing 🤟 💯 🌎
@Sergio29pr 7 ай бұрын
Hi, can you share the link of amazon for the M18 adapter. Thanks.
@chrisb1899 7 ай бұрын
Battery Adapter for Makita 18V Lithium-Ion Cordless Tools, Convert for Milwaukee M18 18V or Dewalt 18V 20V Lithium Battery to Makita 18-volt BL1830 BL1850 LXT Battery Converter, w/ USB Charge Port a.co/d/8kBTF4n
@clintgray1623 8 ай бұрын
Let’s see the final result If 3/4 drain stops up, then the water runs down inside wall, not detected until wall is rotted out?
@JimPiantoni Ай бұрын
calm down negative nancy it looks good to me..
@kurtmd07 8 ай бұрын
Why did you put the new one upside down compared to the original one?
@chrisb1899 8 ай бұрын
It was the same position. It's probably just my camera angle in the video.
@Jfriesheatingandcooling 8 ай бұрын
How does it work on 7/8 lineset. 7/8 repeatedly used?
@chrisb1899 8 ай бұрын
Works great on 7/8 pipe. But like my hand held Hilmor bender , I spray a little WD-40 on the cam to prevent kinking.
@ca916usa6 3 ай бұрын
Good job, like it
@JasonCarter-gb9rk 8 ай бұрын
Chris, appreciate the review, glad to hear that our product worked for you! I designed the box to make installs better for our own ductless installs after dealing with frustrations from dealing with trade related damage and air leakage issues from the backing plates. I’m a 3rd generation HVAC contractor and just am trying to create products that helps my installers do a better job and protects our components during the construction process. Jason Carter, Ingenii President
@chrisb1899 8 ай бұрын
Jason, thanks for the comment. I really like your rough in box for the simplicity and versatile options during rough in. I hope to do a video with 100% completion also. I've been in HVAC for 30 years and love new products that make our jobs easier and cleaner. I'm glad to hear you guys are local also. I'm down in the Tacoma / Puyalluo area . And I think I bought your product at Johnstone if that matters. Take care, and thanks again.
@eastsidepyro2685 9 ай бұрын
Don't you lose vacuum that way?
@chrisb1899 9 ай бұрын
Lose vacuum which way ?
@eastsidepyro2685 9 ай бұрын
@chrisb1899 putting In values before releasing the refrigerant? From how I was taught is to release first after vacuum then put In the valves
@russellsmith5113 9 ай бұрын
Can't find that on Amazon. Can you post an actual link?
@chrisb1899 9 ай бұрын
ERP IG9998 Universal Gas Range Oven Igniter, multicolor a.co/d/iLRjJaR
@chrisb1899 9 ай бұрын
KZbin isn't allowing a link for some reason. Here's the description on Amazon. ERP IG9998 Universal Gas Range Oven Igniter
@th-wt5pn 10 ай бұрын
Never mind i heard u say a 50 ft lineset. Not bad i think I’m getting this vacuum pump im tired of trying to find power and using a cheater cord
@chrisb1899 10 ай бұрын
I was as well. I have majority of Milwaukee tools so it's nice having this vac pump as a option. I also have a Navac cordless with a makita / Milwaukee battery adapter that works just as well.
@th-wt5pn 10 ай бұрын
How long was the lineset if u remember
@270raptor 6 ай бұрын
He said 50’
@courtneyrebecca4health573 10 ай бұрын
Do you need to unplug anything?
@chrisb1899 9 ай бұрын
I didn't unplug power if that's what you meant. I just left the gas oven know turned off. I left a link on another comment regarding the part model if needed.
@jcchan08 10 ай бұрын
I didn't catch what Blueridge Model system you used. Is it M2, M3, M4, M5? S1, S2, S3, S4, S5?
@chrisb1899 10 ай бұрын
The 2 zone outdoor was a BMKH18LM21 . M3 series. You can mix and match the indoor cassettes as needed. The single zone was a S1 series. BMY917.
@hvac_r.tools-Ecuador Жыл бұрын
Excelente
@maxd4968 Жыл бұрын
Actually the single zone unit seems to be a Midea rebage
@maxd4968 Жыл бұрын
These are actually rebadged Gree units. Lennox also rebadges gree
@chrisb1899 Жыл бұрын
You're right. The error codes and Wi-Fi set up are from a Gree manual. Just like RunTru mini splits , but they seem solid for the most part. Haven't had any crazy issues so far.
@fettaboyproductions6022 7 ай бұрын
Give it a couple years Blue ridge minisplits are trash
@tommymein9046 Жыл бұрын
Well done son. It looks better than dragging out 100 feet of extension cords.
@chrisb1899 Жыл бұрын
True ! It's stout for a cordless pump but convenient when 80% of my tools are Milwaukee.
@OnePointLander Жыл бұрын
looks like a red navac pump
@KenB-n1l Жыл бұрын
Br Bre
@jacksinthebox8029 Жыл бұрын
What vacuum hose? 1/2 Navac Big Boy High-Flow?
@chrisb1899 Жыл бұрын
It's a yellow jacket vacuum hose. 1/2 by 1/4. I've got the big blue hose but this works just as good. I've done at least 50 jobs with same hose and not replacing gaskets ( o-rings ).
@jomariot1293 Жыл бұрын
Great job brother! Straight to the point, keep up the good work! Its been cooler then a polar bears toe nails around my house now thanks to you, start calling you Vanilla ice haha 🧊 😎 🧊
@chrisb1899 Жыл бұрын
Thank you sir! It's a fun job for sure. Hope we have more hot days so you can still use it.
@jakebarco-calderon8950 Жыл бұрын
Where did you get that magnetic thing that you hung your gauges on?
@chrisb1899 Жыл бұрын
Trane Supply. I believe it's made by Yellow Jacket.
@KenB-n1l Жыл бұрын
Great job. I have been wanting to try out but thought price was a little high. I have a Navac cordless and works great also.
@ismav3690 Жыл бұрын
I thought there price was high too but then I realized it comes with a m18 8.0 battery and I think those alone are like $250
@chrisb1899 Жыл бұрын
Thanks ! I have a Navac cordless with makita to milwaukee adapter also. However it's only 2 CFM. The Milwaukee has been great for longer lineset or larger commercial unit systems.