This dude is the real deal thanks bob!

uhhhh dude...those aren't concrete sills. More like, sandstone

And that’s how to make your joint look like shit. Use tape on both sides to made perfect and clean caulk joint.

In my experience (homeowner/DYI) inspectors have never been an issue, and have often been helpful in explaining stuff I might have missed. I've wired a whole house (I built) from the pole, did a 100>200 amp service upgrade and so on. The biggest pitfall I think for amateurs, besides not knowing your limits is keeping up with code changes.

Can you use a magnetic seal on a fiberglass door ?

I thought this was going to be about installing concrete window sills, not expansion joint repointing. Typically window stools and sills don't have expansion joints, like he said the contractor either did it this was to save money, or because he couldn't purchase the right size prefabricated concrete sill.

This guy has never brushed his teeth apparently

Bob I have a lime stone door sill that is lose and about to fall out. We just replaced the door about 6 months ago. How can I repair it without taking the door out? The sill will pull out from thunder the door.

Bob ? How to do a outside window seal where thecement has come off and mildew has on cement

First thing my masonry instructor taught is 20 some yrs ago was " real masons DNT use their hands1"

How do the screws on the side effect the efficiency of the downspout? Does it leak around them or catch debris?

Does it have to be a steel door or will it work on a wooden door?

Thank you for this, the morter has almost completely fallen out of a back window on a new house I bought this will help me repair and seal it.

Good job Bob...you're the best!

Wasn’t sure how to secure my downspout to my house since the gutter is against stone. This helped. Thanks, from the handy woman.

How much does it cost to cut a brick windowsill to release pressure on the window frame?

How to remove a castiron plug from a cast y?

Hello Bob~ So, I've installed a lovely security screen door. I have a gap along the top and along the lock side. I've purchased a magnetic door seal kit. Have watched your video in its entirety. Well done! However, the door jam isn't available to insert the kit. Do I need to simply superglue the magnetic side to the screen frame? Frustrated...

Im not licensed electrician but when i got my work inspected the inspector told me i did it better then licensed inspectors its all about safety neatness and logic

Hey Bob. What about garage door seals? The ones at the big hardware stores are crap. I have three 10' garage doors and they are a constant battle.

Wtf, was that a joke on the live circuit?

Fire your camera-man, lol, the guess electrician was showing the outlet connectors and your camera-man was zooming the electrician face, lol. But other than that good information.

Just applied this fix to four windowsills, and I’m very happy with the look. Natural stone, shmatural shmone. Thanks Bob!

What about a metal framed door? Not the door itself but a metal frame that a door is in

Nice vid dad!

First

2:12 - are we still talking about weather stripping

This is good information. You definately need to let your guest talk. I couldn't keep following the video because I was getting annoying.

For godsake QUIT talking over your guest

I’ve seen that a lot

Notice how the decal is still on the mud pan? And no stains on his shirt? Bob isn't a brick mason. But wait, Bob, are you a chemist? An engineer? I'll have a beer with you Bob but it's obvious you have limited experience at what you're trying to teach. Correct me if I'm wrong.

Just watched the whole video. I didn't like it. #brush your teeth

Didnt watch video yet but I can tell I dont like it. #button your shirt

Hey cousin vinny, stop talking over your guests, it’s annoying.

Hi can you tell me how to remove limestone ledge? from under Windows that go all the way around the house. We have aluminum siding and have the Windows then under the Windows is a limestone ledge then under that is brick wall. Any tips tricks or certain tools to use any videos on this you could recommend. Thank you. We want to remove the limestone ledge but be able to put them back on after insulation is put in the walls of the house.

You sir are a fucking idiot that should not be touching any tools, and especially trying to show people construction tutorials

wet the joint first Bob

Great video - please check out Real-Tite® Plugs for the only Nationally Plumbing Code Clean out plug. I do not believe what was put on the end of this pipe will work well. www.Real-TitePlugs.com

This is DIY Nonsense? Using your hand to apply Mortar?

OMG. This video could have been 5 min or less. Less is more.

Bob I think you forget to put gloves

Can I join 3 inch pvc to cast iron even tho the cast iron is slightly smaller in diameter?

why this guy keep cutting his guest's words? too aggressive, and keep talking.

He mentions buying quickcrete with an additive in it, then never mentions the additive nor shows the container very well. Missed an important step there.

"... then you're gonna have a good joint". 🤔

Maybe you could let your guest get a word in once in a while?

Do I need to nail or silicon the strip to the door frame? What keeps the magnetic strip from coming off the wooden frame when the metal door is open?

Awesome video, Bob. Thanks so much. Outside my kitchen, under ground, is a 5" cast iron rusted pipe that joins to a 2" cast iron pipe. I believe it was joined with hydraulic cement!?The 5" cast iron pipes flange is broken. If I cut the 2" pipe and the back of the 5" pipe flange, what can I use to join them together? I heard somewhere about a SERVICE WEIGHT FLANGE. I never seen one or heard of it before. What is your expert advice on this situation? GOD bless and thanks again.

That's a handyman fix and won't last as long as the original defective work. What a complete bullsh#$&er. Where did you do your masonry apprenticeship Bob? That work should be done with S-Type portland cement (mixed 1:3 with brick sand), a tuck pointing sack and a jointer, not with your fingers and a crappy pre-mix product you bought at Canadian Tire or Home Depot. Any first year apprentice in the Brickworkers and Allied Craftworkers Union knows how to do this work, but you clearly don't. You are not a real tradesperson. Like nearly all TV tradespersons, you are unknowledgeable and untrustworthy. It takes more than a pair of work boots and some google searches. Shame on you!

Hi Bob....will mold grew behind that tar paper? instead of using tar paper can I use a delta wrap? thanks.