BEST INFO I'VE SEEN YET, THANKS FOR SHARING

It takes guts

Just bought one yesterday for my dads birthday present for $45. Lets hope i can figure out this paper trick.

1.8 amps? can i just hook up my dewalt drill to it to make it better?

Fantastic video. I would recommend covering testing the capacitance of the capacitor with a digital multimeter as well. A lot of digital meters come with capacitance testing functions now.

cool but i use pencil eraser and it work just fine

Are Grizzly jointers/planners available for EU countries?

Discontinued?

Clip design to hold sand paper is horrible. Waste of time and money. I have to change the paper every three time of use. And I know is not me because I had to call an woodworking expert and when I mentioned he right away told me the system has a flaw. But anyway he installed new san paper and there you go. 10 passes of wood and the sand paper rips. I have two of this machines on my shop and both has the same problem

According to Home Depot:"The best according to Bob Vila!" And on the Bob Vila website it says "we get paid to put these on the list " So its like BS cycle

and they last forever

GET RID OF THE MUSIC!

1.8 Amp motor?? wow I may beable to turn softened aluminum soda cans...lol ;-)

I'm going to get one next week. No two ways about it.

ኑራድን ፈርንቸር

Beautiful cane's and shop

Is this Woodsmith or Grizzly?

Is M2 steel the same as High Speed Steel?

Your out of focus

I have this saw, and it's been the best addition to my shop in years!

NIce job!! What is a DeWalt sander doing in a Grizzly shop??

I needed this! My band saw took a dump while cutting a bar of 12L14. I suspected the cap. Melted! Dropped in a new one and went to work. 90 seconds later, a pop from the capacitor cover and magic blue smoke comes out. Thinking about the problem while machining a block it dawns on me that I'm not hearing a click and I bet it's a switch. Bread crumb trail of clues lead here. I'll follow up.

Brother you lost me at lathe.

EVERY caliper should have the magnetic charge feature and a lithium battery; those mickey mouse little coin cells suck. The OLED screen will have to see over time if that is a good idea.

Beautiful work! I never thought of a rectangle cane shaft! Classy! Thx for sharing this.

I didn’t know you had a showroom in Missouri

Beautiful tool.

Hi . I have a centrifugal pump 2.2kw AC single phase motor. Can I run it on solar without using batteries and inverter

And... I just ordered one! should be here in a week!

Would there be a dealer in Edmonton Alberta Canada for grizzly products ? Im in the market for a milling machine in the future

No miter slot? Would like to see more reviews of this sander!

Perfect. Great use for scrap I've got laying around at the moment!

Somebody is following me. I was just looking at this lathe on website this morning. Nice but a bit pricey for me

When you cut a miter it sure looked like it had a lot of drift. Cut was very wavy. Throughout the video it looked like the blade was going side to side.

Shiraz continues to amaze me, so talented.

This video isn't even showing the right way to do it. There is a tension plate and clip that you preload on the left side. Read the manual. You only tape the right. Grizzly should be embarrassed to put this out. They don't even talk about pre cutting the necessary angles in the paper.

Good work mr. Balolia grizzly is changing lives. Cheers.

All our lathes are between $3K and $8K... except this one... $13K shipped... Oh wait... no DRO and 3-phase. Outboard spider also not listed. Kinda feels like showing this lathe is... let's just say "misguided".

Cool stuff. I purchased a used G1067z wood lathe a couple weeks ago... I love it so far. Thanks for caring about the quality of your products.

Great!

This is an old video, why a repost

Lol yeah not so easy to switch with the 12inch model

Still haven't explained why it's so expensive, it's made in Taiwan or China shipped to Grizzlys where house, where it's sold and shipped again

More shaper videos please. I’m looking to pick one up soon. And prob going with Grizzly.

How about making this press a 1 single phase machine, we need a single not 3 ph

Good machines, who can help me ship one to Uganda, east Africa?

Took a minute to find what i was looking for. This is what I was looking for, thanks.

Got mine. A couple of comments. Received with router mount loose. Bolts not even finger tight. After router tightened in, noted that tolerances on cuts was terrible. Could wiggle router in lift. Better after loose bolts discovered and tightened. Accuracy still limited by the router motor you use. Also, got the free sliding miter and it’s not perpendicular to tabletop. Still messing with it. I used six playing cards to shim it to square it up. Will likely disassemble and bent it into proper shape. A bit disappointing for an $1800 router table add on.

All that and then the freestyle router? Terrifying

Why only 1” top? It should have been at least 1.5 or 1.75”