I gave you a thumbs down due to not knowing how to make a good video. ALWAYS ALWAYS RECORD IN LANDSCAPE MODE! How hard is it to turn your phone so you get a widescreen view? 👎🏻
@SuperDusty111 Жыл бұрын
What model of Rinehart slip on pipes are those? And are they 4 1/2”
@jonathanvermillion72632 жыл бұрын
Those sound badass
@rileyburdine25542 жыл бұрын
Mine didn’t slide that easy Still trying to get baffles out
@heybruh32742 жыл бұрын
Using a broom handle helps get that lined up easier. :-)
@AustinRBa2 жыл бұрын
I'm having an issue where the cases aren't cutting short enough. It's like the case length gauge isn't going in far enough into the trimmer, but I can't twist it in any more. Is there a preferred method for putting the gauge in the trimmer, and knowing that it's in far enough?
@mannytolentino38293 жыл бұрын
Spend the entire time on removal and install to show how it sounds for 5 seconds? Try to edit so we can at lease hear the sound for a bit longer than 5 seconds
@kevingadouas77393 жыл бұрын
Where do you get the dirt can you buy it
@brians15243 жыл бұрын
Great video. Just got mine. Did you have any issues getting off your end caps? Removed the 2 screws and mine won’t budge.
@gregboutwell3 жыл бұрын
I'm taking mine out right now. Soon as I got the two screws out mine would not budge either. I took the bag off so I could get directly over it and put my leg against the pip e and bumped the cap with my hand a few times on both sides and then I was able to twist it a little bit at a time and work it off. Reason I started watching a video is because when my baffle gets almost all the way out it's hanging up on something and won't come the rest of the way out and I can't see in there good enough.
@brians15243 жыл бұрын
@@gregboutwell thanks man. I did. Get mine off. I tried tapping with a rubber mallet but nothing. I ended up grabbing the end cap with both hands and rotating back and forth. There was high temp silicon holding them in. I ended up putting silicon back on after baffle replacement just for the hell of it. Sounds great now. New DBX baffles and new end caps.
@erichardy97883 жыл бұрын
What did you gain from the swap? is there a better sound? better performance?
@brodyoldfield75663 жыл бұрын
Sounds much better and it would be hard to tell performance because I’m sure it’s minimal.
@scotty22214 жыл бұрын
Hey there! I have the 2018 107 cubic inch Road Glide... Same exhaust as yours. What did the high performance baffles do for you? Any louder or deeper? My bike has the stage 1 on it and I'm afraid it could mess up back pressure if I remove or modify the baffles, your thoughts and input would be greatly appreciated sir.
@brodyoldfield75663 жыл бұрын
Definitely louder and whenever you let your engine breath better it will run cooler.
@brodyoldfield75663 жыл бұрын
And I kept my same map and had no problems.
@scotty22213 жыл бұрын
@@brodyoldfield7566 Thanks! Gonna try no baffles first but will probably be TOO loud lol. Then will put in the perf ones like you did.
@garylaurendeau6282 жыл бұрын
@@scotty2221 curious did you put the baffles back in or did you run it without them in how does it sound??
@scotty22212 жыл бұрын
@@garylaurendeau628 I bought the high performance baffles and they sounded really deep and amazing. Always run baffles or it can hurt the motor with not enough back pressure.
@jimregal9284 жыл бұрын
I think you should let the kid help it would be very enjoyable. That's what I used to do now we rebuild engines together.
@brodyoldfield75663 жыл бұрын
Maybe in a couple years. She’s only one here.
@trainwreck15184 жыл бұрын
Any remapping needed?
@harrya33244 жыл бұрын
I have same question. Any remapping. 2020 114
@Meterman19804 жыл бұрын
@@harrya3324 Rinehart said no, when I ask them.
@crazylouie684 жыл бұрын
you didnt use any rvt silicon, the instructions i read says to use it. any reason why you need it or not ?
@rockmo48964 жыл бұрын
I noticed that too. I'm curious to see what he says about it.
@brodyoldfield75663 жыл бұрын
Well I guess I missed that but had no directions. I bought straight from rhinehart when they were in town and just went for it. That being said I’m not going to seal them. I have no rattle or effects from them.
@crazylouie683 жыл бұрын
brody oldfield I put the hi performance baffles on mine, didn’t use the silicon either. Wasn’t necessary in my opinion
@crazylouie684 жыл бұрын
will these fit my 4" rinehart slip ons ? i like the sound but need alittle more growl
@boldfieldbbbbbb4 жыл бұрын
They have them for all their pipes. Just have to order the right ones.
@heathwest37184 жыл бұрын
nice video. Ive got a 15 SGS also denim black with the med red pinstripe. are those slip ons made for the m8 motor and adapted to yours or they mount right up?
@boldfieldbbbbbb4 жыл бұрын
They mount right up. But yes they were made for the m8
@shawnwright91874 жыл бұрын
Rinehart has MotoPro45 Slip ons for Twin cam models and M8 models, but the DBX baffles will work in both. Just need to order the right Slip ons to begin with
@heathwest37184 жыл бұрын
after removing the catalytic converter my 3.5 Rineharts hit like a drunk stepdad and it's much cheaper than a headpipe. the headpipe will accomodate wideband O2 sensors for more fine tuning but for the budget minded I'm super happy
@Fatboy-Rob4 жыл бұрын
Did the kit come with a new retaining plate to secure the new DBX baffle? I pulled my factory RH baffle out today. The retaining plate with 3 bolts in the video is tack welded around the baffle pipe on mine? Looks like it was done at the factory this way. IDK..
@boldfieldbbbbbb4 жыл бұрын
They shouldn’t be Tac welded. The kit doesn’t come with extra.
@boldfieldbbbbbb4 жыл бұрын
Mine were separate and they should be. Strange.
@shawnwright91874 жыл бұрын
I think the first versions of these were tac welded but then they switched to a floating ring. Probably just call Rinehart and they can send you the rings
@streeterboyzoutdoors4 жыл бұрын
Iv struggled making waxed dirt, nay have to try ur way, I have everything there except the paint mixing thing.
@riteshmathur234 жыл бұрын
Are the new bolts any diff? Reason i ask is my kit did not come with new bolts ☹️. Can I use the old bolts?
@boldfieldbbbbbb4 жыл бұрын
Old ones should be fine.
@paulrebis34394 жыл бұрын
Were they alot louder ? From the original baffles
@boldfieldbbbbbb4 жыл бұрын
They considerably louder
@nickbellows95115 жыл бұрын
Where did u get the new baffles
@boldfieldbbbbbb4 жыл бұрын
From rinehart during STURGIS rally
@michealmosley6345 жыл бұрын
Awesome you should have given us a little before and after sound man what I did hear sounded good tho