Will this apply to Toyotas as well

Will this problem apply to anyone else? NOPE!!! Don't waste your time ....unless you've got nothing better to do. This guy is just wanting some attention. .

3gb vram or 6vram

good catch trouble shooting on the rf issue. halogen, florescent (cfl) and early cheap led bulbs used in the motor head unit also messed with the receiver. swapping out to a standard light bulb (Incandescent) always resolved the issue with erratic garage door opening or closing if the board didn't already get fried.

How did you find a compatible circuit board

4:51 move that slip on fitting from close to the one hole to more in the middle of the two holes.

Thank u so much for showing me how to do this! I'm a single mom with 2 kids and I told my landlord our receiver isn't working. That was 6 weeks ago. 😡 He finally sent someone over today April 19th, 2024 and he said I'm here to reprogram your garage! I said I've tried that it's the receiver! Of course he thinks I'm stupid being a woman so he went ahead trying to reprogram it. 15 minutes later he knocks on my door and says "mam u need a new receiver." 🤬 Yep that's what I said! I'm not waiting another 6 weeks, so I ordered a new one and just finished installing it myself! I am so proud! Now I'm sending the bill to my landlord! Love your channel!

Why don't you put the camera in the back yard? We would learn as much with it there as where it is now!

Thanks for the repair instructions. Have a great day.

When he did the dig he had a face like “don’t crash don’t crash don’t crash”lol

Where is this on a 2018 mustang gt?

What was the website?

Can you provide a link of where did you get the board from?

Did anyone try installing a 1080?

My seats not wet. Been happening for about a year.

Thanks! Very helpful.

Yes, try removing the tint D.A.

It *is* illegal, not probably. How on earth have you not been pulled over for your illegally tinted headlights?

Dam my seat dry lol

What is the web site that you got the board from? I need one for an older Blue Max model CM 7500 with a dip switch receiver.

What make and model board did you buy and can you provide a link?

thank you - saved me $$$

bring back the channel

Thank you!

This is probably happening to my 2017 Volt as well. TY for this.

Can you please explain again about why in your case, the receiver board went bad? I have a Genie garage opener (model: Model CM7600IC/A) which recently the "learn button" stopped working. I was shocked to learn from your video as you mentioned that CFL (Compact Fluorescent) bulb may cause interference between the remote and the logic board. In this case, should I replace the light bulbs to LED bulbs right away? Thanks!

The led bulb can affect your remote controls

chris pratt

video sucked

Can someone please help me find the crank position sensor and cam position sensor on my 2014 Ford Mustang v6 3.7? This would be amazing. Thank you.

I can’t follow what’s going on. What is the gD solution?

Where did you get the board do you have a link?

Great video keep up the good work bro My question is my engine makes a winding noise almost sounds like a supercharger the winding noise gets louder when i push the gas pedal to higher RPMs what noise did your alternator make when it went bad ?

Thank you! I just checked my passenger seat and it is in fact wet. I put my car in the sun, hopefully, tomorrow the airbag light is gone.

Was that bank 2?

How did you like the sound over stock?

So in your video you mentioned that you can run an 8-pin card with a 6-pin pcie cable, I tried doing so on my 8-pin 1060, and I still got the error message that I needed to connect pcie slots in order to use the card... Is there any way around this error message or am I just s*** out of luck until 2 days for my adapter piece to come in because nobody physically sells pcie cables which is absolutely ridiculous

Build brothers lmao that's a tida

Close videos old but then i-76700k do you think you could pop a 1650 super in there considering all you need is one six prong plug and a 300 watt power supply I think it will work or do you think it might get too hot it seems like the specs workout but I've never seen anyone try to do it? This is always been a good piece I keep around the terabyte of games on it I got three other PCS but I was just thinking about throwing a super on it probably just because I just have nothing else to do with prices dropping today

It’s 32g and you should have disconnected the battery ribbon before taking the memory out

Are there DIP switches inside the motor housing so I can see if they match up with the DIP switches on the remote? I dropped it and it opened up. In handling it, I may have changed a couple of the switches. Where do I find these switches? I took of the light cover and there is nothing. Are they on the back side, inside of a plastic box or do I need to unscrew something? Challenger 9300. Thanks

Samey same tinted or not

Any difference in temperature?

Where did you get the board?

I've got an 07 gt automatic hit a deer on Halloween night and my insurance company totaled it out because of what the body shop was going to charge to fix it and I bought it back. All cosmetic. Passenger side door passenger fender passenger headlight assembly radiator support front bumper cover and hood. Got all the parts brand new except the door. All that cost around $3000 and I'm getting ready to have it put back together and the whole car repainted for 3000 so in total with parts and cost of fixing it it will be around $6000. The body shop estimate was $8500

Blacked out headlights sacrificing your visibility to others and your ability to see what’s in front of you is something that could bite you in the ass one day. I don’t want to run over a squirrel let alone a pedestrian.

I couldn’t stand my volt engine was noisy when it kicked on

Just tighten gun by hand

Less talk more work

Can you give me a number where you bought yours for that price thank you