Love the concept and appears to be a winner. But, my question is - How often are you cleaning the gray water tank internals and coil surface - surely the detergents residues can build up heat tranfer barrier films that reduce performance, and to to keep drain pipe passages clear of any obstructiona that could cause backed up drains. Thnx!
@microdoulo22507 ай бұрын
Do u have some plan to build myself this type the bench
@kevinwillis6707 Жыл бұрын
clever set up, i like it 👍
@davidreilly1031 Жыл бұрын
I like the DIY low tech style and am inspired to make one customised to my kitchen renovation. My only question is, how do you plan to combat the potential for the occurance of legionnella bacterium, or even smells escaping into the kitchen?
@altontinyhouse7967 Жыл бұрын
The grey water will be teeming with bacteria but it never comes into contact with our fresh water so isn't a hazard. The lid has a rubber seal around it and everything is sealed with fibre glass so no smells escape. I would say it's only worth doing if you have a large amount of warm grey water from say frequent baths or showers. Also best not to have kitchen sink waste dumped into it as there is a much higher amount of solids.
@davidreilly1031 Жыл бұрын
@@altontinyhouse7967 yeah kitchen sink waste isn't always warm either, only worth doing with bath shower and dishwasher, and no more pissing in the shower.
@RustyWalker Жыл бұрын
@@altontinyhouse7967 You usually require double wall applications for heat transfer between grey and potable water. Check your local regs. One way that is on the market is to have a length of copper waste, and wrap the cold feed around it in a tight spiral, and then maybe insulate the whole assembly.
@CreativeCarpentry2 жыл бұрын
It’s a good solution for you at this stage - you have lots of ideas how to modify it to suit different applications so it will do what’s required , as you do more jobs and grow your business I’m sure you will get bigger and better tools to suit your changing needs but I’ve found no matter how many tools I get I always need to get creative to do some jobs quicker or more accurately !! That’s where quality and revenue can be increased using your head . 👍
@cognitor9003 жыл бұрын
Love the idea of measures outside of the 8’x4’ sheets. I suppose the ginormously expensive rail squares at £100+ is another option to avoid walking around the bench? I nearly ordered one a couple of nights ago from benchdogsuk but baulked at the last moment with 30quid freight to Australia.....now I have to wait until May. Bugger.....! How about a multi legged stirrup/Jack/brackets along the vertical edge of the other bench against the wall to hold that lovely expensive piece of Festool track? I was getting nervous just watching it standing up against the bench.....it’s an expensive oopsie. Good luck with your channel, stay vaccinated and greetings from the south western corner of Australia.
@edmillar72643 жыл бұрын
Great! Looking forward to more videos!
@remco60073 жыл бұрын
yesssss nice 👍🏿
@NicoSmets3 жыл бұрын
Interesting setup. Thank you for sharing.
@geolisadrag-racing23493 жыл бұрын
Great video👍. I have some serious medical limitations; but i am trying to make a return to building. I've been trying to plan out a small work bench. One design consideration has 90 degreee dog holes & track around the table. Similar to yours but on a much smaller scale. How did you lay out & drill your dog holes? thanks again 🔧Lisa♿
@cognitor9003 жыл бұрын
Other than finding someone who can cnc it (getting cheaper all the time) there are some template/jigs on eBay if you search for 20mm dogholes but most (many) serious Festool (founders of the 20mm holes on 96mm centres system) use a clever British chap’s invention called the Parfguide System. Comes complete with 20mm drill bit, Pythagorean based simple system with jigs, specialised rules etc. Gives you the best chance of consistent holes EXACTLY the correct distance apart. Festool pioneered the 20mm holes, 96mm apart, and they have developed their own clamps, work tables, saws, routers, and opportunities for consumer poverty across many of their systems. When you’re sick of getting things almost accurate but you just want perfect instead ..... Anyhow, sorry for rambling but I hope that the information helps.
@adammabe58193 жыл бұрын
As I'm searching for a solution to my problem of being unwilling to pay for an MFT while really wanting the ease and functionality it seems to bring to the track saw, I'm carefully weighing options. I landed on your video a week or so ago and have revisited several times. I'm wondering if you're still using this setup, and if so, I'm curious about any solutions you might have come up with for the pain points you so honestly shared. I find the discussion of one's thought process to be just as valuable as the genius ideas themselves, if not more so, so I really appreciated this offering. Thanks for your time and effort!
@burnhamsjoinery43223 жыл бұрын
Hi Adam - I'm an Adam too! Other than putting a couple of brackets under the bench to put the long rail I haven't. I'd love one day to make a cnc version of this with all the stops moving with a push of a button but I doubt that will happen before I retire! Good luck.
@-aleeke-25263 жыл бұрын
Wow!
@-aleeke-25263 жыл бұрын
I am thinking about getting a tablesaw since my combined miter and table saw sucks. But I found out today that they are very expensive. So I am looking for clips about how to use a this kind of saw instead and your table have given me great ideas good job. Also you should build a storage shelf under for the guides.
@burnhamsjoinery43223 жыл бұрын
I just bought a new 2.7m rail and took up your good advice to add some storage brackets for it - thanks!
@ThekiBoran3 жыл бұрын
@@burnhamsjoinery4322 I recently simply screwed 2 2x4s to the saw horses that hold my bench. With my TSO parallel guides with the quick adapters it's very convenient.
@phillips10033 жыл бұрын
@@burnhamsjoinery4322l love that setup! Thanks for the idea!
@shandonjulius50203 жыл бұрын
Wow.brilliant.perhaps you can incorporate blades into your fence at the right height to trim top and bottom as board is pulled through ?
@GNU_Linux_for_good3 жыл бұрын
10:01 No, no - you *don't* have to *run* around.. Do it [a little swifter of course] like this guy: kzbin.info/www/bejne/aHm5lqyYqptljck Ha, ha.. Cool solution. And in the next episode Mr. Brunhams will make some actual cuts with his precious TS55 instead of *only* talking about and explaining things.
@1patfin4 жыл бұрын
You are a genius. Been looking for a cheaper way to edge band. And I now found my answer. Only problem I don't have any knowledge of relays or pneumatics. But I'm sure I'll find someone who does. Thanks again 👍
@ExpoMaster4 жыл бұрын
This is amazing! I liked it so much! I also made edge bander transformer
@markrussell97194 жыл бұрын
Very clever well done - just subscribed.
@Alloush19805 жыл бұрын
Nice work.... Any plans how to make it?
@adamburnhams95715 жыл бұрын
Sorry I don't have anything written out. I'm planning to remake and improve it within the next year so will post a new video then.
@rooikatza5 жыл бұрын
Genius,you seem like the kinda guy i am,alot of people say its easier to use a proper edgebander,but building something yourself and seeing it work and using it gives you pride and saves money!i like it!
@bikboklv5 жыл бұрын
some great ideas, thnx
@jameshewett20095 жыл бұрын
Clever and efficient - thanks for sharing :)
@Alastair_Freebird5 жыл бұрын
Thanks for sharing this Adam great idea 👍
@Larry1942Will6 жыл бұрын
Nice job. How thick of banding can it use?
@adamburnhams17926 жыл бұрын
2mm just about works but takes a bit of tweaking to get it running smoothly
@Larry1942Will6 жыл бұрын
That's good. We use more 2mm than any other. I didn't know you could get 2mm with pre-applied adhesive. We use very little .018 (.5mm) And quite a bit of 3mm. All run on automatic edgebanders.
@paravaliramesh90557 жыл бұрын
very nice how much this mission
@TwistedxLion7 жыл бұрын
In our workshop we have a brand new tornado plus edge bander looking at this video seems like madness aha it's so much easier with a proper edge bander aha
@hkrsescort6 жыл бұрын
TwistedxLion / Sw Wolves yes, this is complete madness. How to over complicate a simple process and make it hard to manage
@dimmaz882 жыл бұрын
You've missed the point, some people like to solve problems themselves, others just like to buy stuff. This is far more fulfilling than spending £10000 on a new machine, and a damn sight cheaper.
@symont30628 жыл бұрын
Very cool. thanks for sharing!
@Woodentoolcompany28 жыл бұрын
Very impressive if I must say.
@alistairmackay77618 жыл бұрын
great well done love the cut off knife
@md.abdullah84898 жыл бұрын
how to glue on the edging?
@gbestwick5 жыл бұрын
I'm pretty sure the heat gun is there to heat up the hot melt glue that is pre applied to the strip