Nice animations, simple explanations. Nice work guys.

How to use ? Can you teach me plz

Hi, I´m thankful if you can answer the following: Where did get the fasteners between the linear actuators and universal joint in the base?And where did you get the universal joints?

Damn $70 per actuator?!

Could this be used for a solar panel?

Could you tell me the name of this liner actuators

5V or 12V for the linear actuator? What kind of easy to use non wall plugged power source are you using? Looking for a 12V solution but uncertain

Nice

That's great!

Excuse me, but can Actuonix create a similar custom device for their customers? If I wanted to make something similar to this to be utilized as a filmmaking prop, would it be possible and how much would it cost?

But does it cut along the dotted line like your art teacher instructed?

Try a seat motor or a window regulator motor.

Um atuador linear desses deve ser bom pra colocar numa escavadeira/carregadeira de brinquedo. Eu tenho uma só não tenho oa atuadores.

That is the 2nd COoLest mini-servo I've seen to date. Thank you.

What’s the total weight here? I’m planning on converting my adjustable spoiler into an active wing using two of these actuators I was wondering if they where strong enough to cope with the downforce especially as I plan for the spoiler to work as an air brake also

Can this be setup to make this cycle every 12 hours? Ei. Cycle out then retract daily at 7am then 7 pm? Very interested.

Did you ever mount this and put it to use? How long before you took it off after?

What parts do I need and where can I get

I want the Cable Piston to move back and forth at all times, without changing energy directions. What should I do.

Can you wire four aculators together to a rocker switch

Well done! And the actuator itself only weigh 95 gram according to specs!

Hi, what is the type of input used, could the input pin be hooked up to a potentiometer, with the low side grounded to the power supply ?

hey what kind of motor u use in fingers to move

love to see some wrist movement

Nice Servo Actuator. I am using 2 different versions of Actuator, one of them work with Arduino with 1ms pulse, but the other does not work. Using RC controller both work, someone has experienced the same issue? Thanks in advance for your comments!

Can this be set up to essentially bounce back and forth between the two limit switches? Essentially each limit switch reverses the polarity of motor? Thanks!

I’m looking to make a Halloween decoration for a spider to move up and down. Can you tell me the parts I will need to use this motor to do this? Thank you

can you please provide code for this

Hello, I would like to use an actuator with position sensor and commanded by a rocker switch, what models are recommended, I looking for this solution in your web site, but I don't know if I need or not of the control board and if the control board allows be commanded by a rocker switch. I'm plan to order the products when I got these answers. I have 2 possible applications, first to command an elevator trim tab in an experimental airplane and second with 3 fixed positions to command a wing flaps.

🖖 👍

Can we see it working outside?

How to avail the timer switched

Hi just wondering are you only using 2 wire from the rc controller, did you cut the 5 volt?

When I plug in the control board to my computer via USB, it still says device not detected. I have the actuator correctly plugged in, and a 12 Volt battery pack wired to the board. I followed everything exactly and still cannot get it to work. Can y'all please tell me what I did wrong?

Can these be manually pulled in or out?

exactly what im trying to do

I’m going to do something like this with a lift chair actuator to control a door for my chickens. I have the 24 V linear actuator and the power supply. I have no experience with Arduino‘s

Suggest you put up a video showing the actuators installed in small to large fixed wing model aircraft to operate control surfaces,

hi the the arm goes out and then goes back is there a constant voltage to it as i want to push a button on my window blind remote control but i need one that pushes and retracts all in one cycle my 12v is constant i think this would work as long as the 12 v input can stay constant . i want it to push button then retract after 1 second and then not come on again until the power is cut and then comes on again as its a projector in a cinama so the projector comes on triggers your timer the arm pushes the button on the remote and the window blinds come down and i dont want the button re pressed untill the next time i use cinama please help i dont want it to run continuously just one cycle or the blinds will be going back up again as the button would be re pressed again and again please help cheers sir

What is the cost of all the components for this?

Very cool

I need one for my skymaster F-18 speed brake but I do not know what to choose!! Any help would be appreciated

question? I have the P16, if i want to open and close the gear doors on an RC airplane, can I program the degree of travel each way using this set up with a 2 position switch?

how can we wire it to raspberry pi pins? is any extra cable in the package?

Can this be added to an okin tv stand actuator?

Do i need to change the polarity if want to retract?

Can wire it to a one button switch? Like an auxiliary switch on a key fob

maybe this can help me build my hand, and legs. ( I am not missing them, I am just building an android. Any suggestions or ideas?)

Why don't you just use the linear servo's shaft to slide in to the pipe? The whole wire plus shaft thingy is redundant.

Does this work with the P8 micro actuator?