Thanks 🙏

Thanks , we appreciate your support.

Thanks for watching 👍

@@Kellislawnservice Welcome I am a new subscriber to your KZbin channel and I did an audit report for your channel and found some issues that I think should be addressed. I think your KZbin will grow a lot if you solve the problems. I can show you the audit report if you want. Thank you

Yeah , I’ve lost a few battles like that .

Thanks , me too.

You and me both!

That’s great 👍

Thanks for the input, we appreciate it .

The blower adds 9inches on my machine. Idk if the new style takes up less space.

It’s lower to the edge of the mower deck .

I agree, thanks for watching.

That can be a challenge to find one in good condition used .

We have been running this setup well over a year . It has more than enough power at 540 . I really love this set . Thanks for watching.

It will create more wear & tear , but the performance is great . Thanks for watching.

That’s great , hope they keep rolling.

Yes

Yes that seemed to be the only way . It really went easier than it looks . Best of luck , and thanks for watching.

Took a couple hours, start to finish.

Thanks, the stereo is a Sony .

I know the FS & FX basically have different air intakes . Not sure about the other two .

Pine needles are a challenge for sure . The x blades help ,but you still have to spread them out over a larger to mulch .

It sure does a great job on brush . If it’s really heavy it just takes a bit longer, but the outcome is the same . Thanks for watching.

Yes , Fradan is really well built product. Thanks for watching.

Maybe a small area you could rake out , but not one this size . I’m way too old to try 😂

@@Kellislawnservice it’s about a 10x20 foot area! And man you are so right! I keep looking at it thinking about the labor vs my body! 🤣🤣🤣🤣

@@jeffwisenightvisionproduct1991 it might be easier to just add gravel and spread.

@@Kellislawnservice that was my first thought before I saw the results of what you did. But yes that’s probably what I will do.

Thank you

Bearings are pretty cheap to replace, so far we haven’t had any problems. If you change the entire spindle it can be costly. Thanks for watching.

Thank you 🙏

It’s a very convenient tool , and makes a lot of jobs easier. Thanks for watching, we appreciate it.

It’s never a job I look forward to , but yeah it’s best to just get them all done . Thanks for watching, and good luck with yours.

Yes it actually cuts really even . They also make grass blades for it instead of the heavy hammer blades.

Yeah they were pretty bad lol 😂

Thanks for watching, we are constantly fixing something.

Thanks for watching. My advice is pick a cooler day lol .

@@Kellislawnservice 🤣🤣🤣

Nice to meet you both ( I saw the boat ride video) and congrats on your new homestead. Thanks for the follow , and maybe we’ll cross paths soon. Peace ✌️

@@Kellislawnservice we will be in AC early October! Just booked a 4 night stay at the Trop South Tower.

Thanks for watching 👍

@@Kellislawnservice The 500S is not as easy. it is easier if you take the wheel off.

@@georgerogero3185 yes they can be challenging.

Thank you so much.

Glad you enjoyed it , thanks for watching.

Thank you Mark .

Thank you , I’m glad to be a help. Yes , it seems like every single one has a different clip of some sort . Thanks for watching, we really appreciate it 👍

Yes , especially up here in the north east. It is a fight with all the vehicles.

Hey there , especially in the spring when the grass is really growing fast you may have to double cut . The clumping grass can hold the other blades down and miss . If you cut biweekly the grass can also get too tall requiring a second pass . Thanks for watching, we really appreciate it 👍

@Kellislawnservice Thank you and you have another subscriber .

Yes , the staples work great . Thanks for watching 👍

Thanks so much .

It sure was hot out . Thanks

Thanks , but next time I will fill the filters before reinstalling. Thanks for watching.👍

​@@Kellislawnservice A technique that worked for me was to spin the left (pre-)filter on just enough to hold it in place, still leaving a gap above the gasket to allow the flow from the filter mount to fill the filter. Once the filter was full as evidenced by full flow volume into the drain pan resuming, I spun the filter on the rest of the way to seal it. I was about to fill the right filter from a fuel can before installing it but started to feel funny about pouring unfiltered fuel in there considering the fact this is apparently the final filter. I also had a hunch this filter is on the pressure side of the fuel pump so decided to install the filter empty. I gave the tractor a few extra seconds to prime itself between turning the key from On to Start, and sure enough it started immediately with no problems. Now I just am wondering how much/fast hydraulic fluid will flow if I try to replace the hydraulic filters without draining the fluid. Deere says the fluid can stay in for 1200 hours if it's tested. I'll probably try and find somewhere to test the fluid as just to be proper, but I suspect it's in good shape since I use the tractor mostly for snowblowing (I have an aftermarket cab on mine) so the system stays clean and for the most part sealed up all season without much chance for water or dirt to get in.

@@RyanRBiggs good idea with the fuel filter, I’ll try that next service. I haven’t changed the hydraulic fluid or filters yet , only at 600ish hours.

Thanks so much . Who knows maybe we’ll expand to NY . It might be worth it for the pizza alone 😂

Thank you so much , we really appreciate your comments.

Thank you , we appreciate your comments. Yes the best time to trim is right after they finish blooming.

Thank you so much 😊

Thank you 🙏