It appears your lathe needs a good refurbishing, just an observation.

is it possible to replace the bearing without completely dismantling the engine ?

Sally will be back soon… she’s in good hands.

Rolled towards the mill slightly

For any DYI guys viewing in 2024. The cheap motorcycle blind/wheel bearing puller set on Amazon will get these out. The 25mm or 1" is the size you want, and it will do your wheel bearings too. P.s, the book says to pull the balancer and the bearing as one. Mine where so tight the balancer came out of the bearing, so the bearing was left in the case.

😎👍😎

it looked like from here case moved a bit mate

Is he adding lead or aluminum? I guess he changed some thing that was stock so he has to adjust for it. Thanks, Thailand Paul 1950 RIKUO 750cc engine, grenaded. To be continued, hahhaha. Weld we must!

Why dont you use brass for the bushing?

👍👍👍

Why do you buy this junk???

These videos are the I enjoy.. you're great at sharing knows and teaching .. if someone is interested in building a new knuckle or panhead who makes the best quality aftermarket cases??

👍👋👋👋👋✌️

I'm glad to see life has calmed down on you, and you have the chance to get back to the backlog of work facing you!

Good stuff Keenan.

🇰🇷🇰🇷🇰🇷오늘I hope you have a lively and rewarding day today 🙏 😊 😍😍😍😍❤️❤️❤️🇰🇷🇰🇷🇰🇷

There was a bolt at bottom of the box that you threw to the floor

It's meant to mainly cut w ease to avoid you straining your hands from squeezing too much

No valve seal on the exhaust?

First let me offer my sincere condolences on the recent loss of your mother! Lost mine not to long ago, even though im 62 I was still her baby, thats a special bond unlike any other. 🙏 Id like to ask a question not pertaining to your video. Question! Do you gap Iridium spark plugs the same space as a standard plug. I have them in a dual plugged head Ultima 96" shovelhead motor. Normal shovelhead gap is 38-42. When i checked the gap on the Iradium plugs they were all gapped much closer than that. ? Thank You! Regards!

Had a friend with a original pan , sent his tombstone to be cromed ,they forgot it in the acid bath. He was pissed. Gone forever

If I ever need a hard to find part I’ll no who will have one 👍

I have a 1975 ironhead xlh 1000 with drag pipes. I have a super E carb and I was wondering what size jets do you think will work best in it! Air bleed, main , and intermediate. The engine is stock original. Any help would be great thanks.

The groove on top may have been put there by somebody building a bobber with a rear fender that was real close to the tire.

✌

✌

✌

✌

✌

✌

You wouldn’t happen to have a linkert dc12 ?

Do you make the weights if so what would it cost to make some

Just bought a pair of early Big Twin Evo tappet blocks for $70 on Fleabay

🇰🇷🇰🇷🇰🇷오늘I hope you have a lively and rewarding day today 🙏 😊 😍😍😍😍❤️❤️❤️🇰🇷🇰🇷🇰🇷

lighter than it was but still heavy! well said sir!

Might hafta consider a Ultima for the 05 injected anemic 88" Road Kink

YOU LOOK AWESOME BROTHER LONG TIME NO SEE!!!!

Just an observation... The part should fit everyone's tool being an industry standard tool. Customize/replace the part to meet the industry standard.

What's in the Vevor box?

it's 120 ft. lbs for the master cylinder screws.

In my ironhead servive manual it shows an ammeter, a voltmeter and a variable resistor required for the test. But, it doesn't say anything about the type of resistor, or the wattage it needs to handle?

Fred is back! Love his dry humor. Now we need Helen of Estonia 😅

I was told if there’s no oil under it then there’s no oil in it

Guy is selling 2005 harley davidson sportster 1200 xl custom He say chain was over tightened damaged flywheel assemby and needs replaced ? If this is possible, I don’t know anything about motorcycles be honest with you. I haven’t had one in years. How hard is it to do?

Fast as a 600 until the first turn. lol. Love the videos! And who needs the gym when you have twin cams to lift?

A choice of dry open primary or the wet set, I have a running bike now, I'm in Elko nv

I'm watching your videos, I have a early EVO on the bench, starting the gasket cleaning process, in-between work...I love e your videos, Thank you

I know what you are going through my sincere condolences.

Never have idle to low top end needs oil as well am not saying it to low just a tip .

Sorry for the hard year Tatro. Ready to see more expert work. As for the E-VO, I currently have a 114 before my Twin cam. But I still believe the best engine HD ever made was and is the Evo. Bullet proof. I know I put one through some hard times but it never missed a lick.