Spoop-D printing

Titled "Remove and clean" and finished with "it's not spraying uniformly. I guess we will leave it this way"

Hello, after disassembling and cleaning everything, I found that the filter was closed.

I took the nozzle (two screws) let it seat on a small plastic cup with vineger (used in salads) for 1 hour, then use a little air pump and flush it, put back in place and works as new.

Are you able to list the make and model f your Ultrasonic Cleaner ?

Thanks but audio instruction and reassembly are needed.

I took mine a part. I ran vinegar through the tubes. I soaked the nozzle in baking soda and vinegar overnight. Right away I noticed debris floating in the water. Now it works like brand new. Thank you for posting. Don’t tighten the screws too tight that will make them almost impossible to remove for the next time you need to open the casing. This was a helpful video! You saved my braava. Subbed!

Check wiring. Fixed a similar problem for me.

I have tried about anything to get the nozzle clean. aircompressor syringe with different sullutions and more. At last I bought a small sonic cleaner, and put the nozzle in a small glass with vinegar (ättika 24%) and fill up the cleaner with water outside the glass. Run it for 10 minutes and it sprays like a new nozzle again. (Y)

My husband just used a can of compressed air, like you clean your computer keyboard with, to unclog mine.

Useless for me at least, I end up creating a new nozzle myself using some plastic epoxy and a a piece of pen tubing.

ma questi sono i famosi video che anni fa avevi condiviso sul forum del fiat panda club italia o sei tornato di nuovo a caponord?

Finally got mine clear with Spirits of Salt (low-strength hydrochloric acid), a short length of tubing and a syringe to make sure the acid was properly sucked all the way through.

You can take off the nozzle and put the small blue pipe out through the hole with something to pinch it: it won't "spray" but at least there will be water put in front of the robot. It's better than throwing the whole machine to the garbage. I'll try to put another spray nose (from perfume bottle) - it should work since the pump exert pressure to open the nozzle so it's basically the same mechanism

Just to give you update. I have just communicated with iRobot customer representative and told me that my Bravaa Jet robot needs to be replaced. Quote "We do not advise removing the nozzle off the robot since it's the core of the unit." Another quote "based on the robot's behavior at this point the robot will need to be replaced". I told her that my nozzle is clogged and insisted me to replace my robot. Crazy and ridiculous right? Well, I have no choice but to fabricate my own nozzle. I will update you guys. Still waiting for my resin 3D printer.

Mine is clogged and releasing droplets of water only. This replacement parts is nowhere to be found in the internet and most probably I might 3D print this part using resin material. Already sent message to iRobot customer service to inquire where to buy this spare but still no reply. Anyone knows where to buy this spare part?

Do you clean your the electric toothbrush base in ultrasonic cleaner as well?? I want to but afraid gonna ruin it, is it safe??

Great, now I have to pee...🤨😤😰😭🥶😓😥😰😨😱😪😴😴😴😴😴😴😴😴😴😴

My Braava is not going in a straight direction anymore, and I believe is the right side wheel rubber that is gone. Any idea how can I replace it. iRobot charges 79 USD. !

?????????😴😴😴😴

heilà Olaf, ti sei dato anche tu hai video tutorial? bravo! solo che secondo me dovresti descrivere a voce quello che fai, in italiano o in inglese, come preferisci

questo problema era capitato anche a me al ritorno da bologna, ho risolti rinforzando la contro molla dell'accelleratore

*Vietnam flashbacks*

Wonderful Day! Thank you for sharing this with us!! I was also there and enjoyed it a lot. Is it possible to share a little more?

This ways is moneys . . ! Bleach into small cup then all your tooth brush head in for few hours . . will be clean like new .