Hello Tech 3D I would like drawer slide is dimensions? by Length? and thickness? Thanks CDLT
@Tech-3DКүн бұрын
448 x 450 x 12 mm
@SteveB-i1j3 күн бұрын
Mine is square with Makita track.
@ricardoaznarez12704 күн бұрын
Hola cuál es mejor el 35L o el 35M gracias
@Tech-3D4 күн бұрын
Se trata más bien de lo que hay que aspirar. Si solo necesita filtración de partículas de polvo de clase L o si necesita filtración de polvo de clase M. A partir de ahí, siguen las características de la aspiradora.
@Weldur_Mekanik6 күн бұрын
Zdar svar, nevi někdo kterej trimmer poštelovat aby tam nebyl 2s post flow? Na dlouhý vyvařování aut je to akorát žrout plynu, vidim jich celkem 6, RT1-6 jsou to w104 a w204
@Tech-3D6 күн бұрын
Domnievam sa, že to nemá analógové riadenie.
@Weldur_MekanikКүн бұрын
Tak to abych koupil tu novější verzi jen kvuli takove blbosti že tam někdo nastavil brutalni dofuk🙈🤣každopadně diky za odpověď
@broom695810 күн бұрын
Recommended for polishing plastic as well?
@ErikMajlath10 күн бұрын
Where did you order this unit please?
@Tech-3D10 күн бұрын
I was buying it on ebay.de
@MrEllhel13 күн бұрын
Scheise..länger Tüten am auspacken als arbeiten..
@undiciable13 күн бұрын
Isn't the grip kinda bothering like that? I wonder why they put a clip there, is not like it is actually dangerous if you just push. I hoped to find a cheaper alternative to Mirka but I start to think that nobody created something that practical as their 32mm grinder
@--Mike--14 күн бұрын
And you get that neat little dust catcher for just a thousand bucks.
@Tech-3D13 күн бұрын
For the cutting capacity, the power, the space saved on the glide and the quality of workmanship, it is not that expensive. In Europe, it costs much less.
@Amael09075616 күн бұрын
I would shurely never do that
@Tech-3D16 күн бұрын
I agree
@m3chanist18 күн бұрын
This is a great unit, sure as hell beats sweeping out the workshop floor each night, job done in minutes. Powerful little beast is enough to blow out any and all debris.
@Tech-3D18 күн бұрын
I agree. For me, it has replaced the frequent turning on of the compressor just to clean some dust off.
@VoxidjonXolrajabov20 күн бұрын
🖐️👍👏
@mgtowski39521 күн бұрын
How much would it cost DeWalt to add this at the factory? $2? Why not offer it and charge $20 or even $30 more?
@Prepper_Raider27 күн бұрын
Be nice if you _didn't_ adjust the playback speed so people that hit pause trying to read are not having to pause on a fuzzy video.
@davidokuniewicz400829 күн бұрын
Omg wehre cn i buy it ??? Its realy genius 😍👍🤟
@Tech-3D29 күн бұрын
You can buy the 3D model at the link below the video.
@davidokuniewicz400829 күн бұрын
You are realy impressive i love your genius ideas 👍❤️🤟
@Tech-3D29 күн бұрын
Thank You
@kjellliem7004Ай бұрын
what was the start up amperage with the soft start installed? I only saw the shape not the value. thanks.
@lvmadsenАй бұрын
Just got my miter Guage yesterday - downloaded and printet this wall mount - fits perfect. GREAT job
@Tech-3DАй бұрын
Thank You
@aki4737Ай бұрын
I have a model 2200 which is great but I made a cover for the light to keep it from getting scratched. www.printables.com/model/642463-bosch-gli-18v-2200c-lens-protection-cover
@joytekbАй бұрын
Cool
@TheGuggoАй бұрын
I cannot hear any comment on the saw due to the very loud music...
@Tech-3DАй бұрын
That's perfectly fine. That's because there is no commentary in the video.
@thedubwhisperer2157Ай бұрын
2:03 For best results and lowest vibration, all tooth grinds should match - not an angled tooth next to a flat topped one!
@yonatanalony4233Ай бұрын
Thanks for the video, did you happen to use it? How's the plunging? Is it any good? Thanks.
@Tech-3DАй бұрын
I don't have this router anymore. I replaced it with Bosch GOF 1250 LCE kzbin.info/www/bejne/lWaVamN8ntGkm8k
@moonday1111Ай бұрын
Brilliant
@speedboatbuilderАй бұрын
Thanks, the wires on my saw are different colours but I fitted the soft start in the same position and it works fine.
@ahmetemindilbenАй бұрын
Hi. Can i use the original step motor from ender 3 pro's extruder in this?
@Tech-3DАй бұрын
Yes, no problem. It's the same size.
@gerkerkhovenАй бұрын
Important video! Thx!
@arcusarcus8196Ай бұрын
For inverters, it is not good to overdo it with a large inductance of the chokes, because a large inductance can create an overvoltage at large currents and voltages on the rectifier side and blow up diodes or other sensitive semiconductors in the final stage and destroy the device !!
@diy_7451Ай бұрын
Wonderful as always!!!!
@Tech-3DАй бұрын
Oh... thank you very much
@nixlandАй бұрын
Any video about the purpose of each of those grinding discs ?
@Tech-3DАй бұрын
The video is about the presentation of the grinder. There are countless grinding wheels on the market and several manufacturers. You need to search on KZbin.
@nixlandАй бұрын
@@Tech-3D I know the video is about the tool not the discs, but I wonder if you have made videos about the discs which I am interested to see.
@trokt2Ай бұрын
Sir, you win. Kompernass doesn't have spare parkside guide rails available right now, so I thought I needed to buy an expensive evolution rail. I wasn't gonna cut my makita rail, but you just showed me the way. Thank you very much.
@arcusarcus8196Ай бұрын
This welder is primarily intended for MIG welding! You didn't help it by introducing the induction coil, you modified the MMA method as much as possible, which is secondary on this welder and it doesn't make sense to use it much. But you did a lot of damage to the MiG method which is primary and more important! This welder is very well tuned from the factory!!! It does not need another induction! and by introducing the induction coil without measurement, you greatly disturbed the regulation of the output voltage and its rapid stabilization in the MIG process. By senseless modification of a perfectly tuned welding machine, you have degraded and devalued it! Here you do not understand the principle in electronic devices at all and you manipulate the public in meaningless expensive modifications, the only good thing is to change the cable
@arcusarcus8196Ай бұрын
Tahle svarecka je primárně určena k svařování metodou MIG ! Zavedením Druhé Tlumivky ste ji Nepomohl ,maximalne kapanek upravil metodu MMA která na téhle svarecke je druhotna a nemá význam ji moc používat . Ale hodně ste uškodil metodě MiG která je primární a Důležitější ! Tahle svarecka je z vyrobí velice dobře vyladěna !!! Nepotřebuje další indukci ! a zavedením Druhé tlumivky bez měření ,ste hodne narušil regulaci výstupního napětí a jeho rycle stabilizaci v procesu MIG . Nesmyslnou úpravou perfektně vyladěné svářečky ste ji zdegradoval a znehodnoťil ! Tady vůbec nechápete princip v elektronických zařízení a manypulujete veřejnost v nesmyslným úpravách
@arcusarcus8196Ай бұрын
U invertorů není dobré to přehánět s velkou indukčností tlumivek, protože velká indukčnost může při velkých proudech a napětí na straně usměrňovače udělat přepětí a odpálit diody, nebo jiné citlivé polovodiče v koncovém stupni a zničit přístroj !
@crapper182Ай бұрын
Amazing, I got 4 of them today and a 3d printer a week ago, I was just looking for a review video and got this gem, I was looking for copper and found gold, thanks!
@ravenmoooreАй бұрын
Does it work without some sort of pull-down resistor on the other pins? I thought it has some security or protection preventing direct usage. nice!
@Tech-3DАй бұрын
It works normally. Bosch batteries have their own protection against under-discharge.
@AlexBeerForEveryoneАй бұрын
@@Tech-3D did you test if the under-discharge protection works like this? it's a bit difficult to get reliable information on this. some say the the protection is built only into the tool, others say newer high capacity models have built it into the battery as well. but bosch doesn't say much about how their undervoltage protection works, or at least i didn't find it yet.
@womackoАй бұрын
@@AlexBeerForEveryone I'm very interested in that topic too. I want to use it like shown, but want to ensure it has a discharge protection.
@zenddoor14 күн бұрын
On procore battery teardown videos you can see that the 18V terminals are directly connected to the cells (just one fuse inbetween). So if there is undervoltage protection it would have to be integrated in the Samsung cells, maybe you can find that out, the cells are labeled on the video I saw. The Bosch tools probably get a signal from the procore's bms to turn themselves off when charge is low. I would not count on it having protection on the terminals, so keep checking the charge indicator when using it with an adapter.
@Tech-3D4 күн бұрын
The Bosch ProCORE, discharge, short-circuit and overheat protection for Bosch batteries is official Bosch information and is also in the guidelines for Ampshare compatible tools that use Bosch batteries.
@Александр-ш3з3пАй бұрын
Здравствуйте ,спасибо за обзор и проделанную работу.Можно у Вас попросить выложить STL файл данного проекта ,я понимаю это лично Ваш труд и каждый труд должен чем то вознаграждаться,но все таки как то можно это сделать. Спасибо. Hello, thanks for the review and the work done.You can ask me to upload the STL file of this project, I understand this is your personal work and every work should be rewarded with something, but still, somehow it can be done. Thank you.
@Tech-3DАй бұрын
The link is in the description to the video.
@Александр-ш3з3пАй бұрын
@@Tech-3D Thanks for the paid link
@jeanlemire2681Ай бұрын
In other videos I saw that they use the white plastic disks with ridges to avoid chippers from sliding and hitting the saw blades. Also, they assemble the stack before putting it on the saw's arbor.
@daveworkman5213Ай бұрын
Depends on what width you're going for whether you use those white spacers. The carbide teeth are still protected from hitting another tooth by ridges in the left and right blade that lock the tooth in place.
@moscott72922 ай бұрын
Just bought this clamp this month and there doesnt seem to be any shift. They must have improved it.🙂
@zeekfitzroy49862 ай бұрын
ASMR Grinder bliss! Great, mesmerizing video!
@bigj-dogg96732 ай бұрын
Where can I by these
@Tech-3D2 ай бұрын
you can print it on a 3D printer, the link is under the video, or buy the finished product, send me an email.
@bigj-dogg9673Ай бұрын
@@Tech-3D what’s your email
@brunomars76352 ай бұрын
Thanks for this review, i will pourchase it soon but I can’t find the wall bracket, do you have a link ?
@Tech-3D2 ай бұрын
kzbin.info/www/bejne/aWG9fmadmdF-l5Y Link to the 3D model below the video
@brunomars76352 ай бұрын
Thanks a lot 🤩
@hellolau2 ай бұрын
Nice !
@리인텔2 ай бұрын
Good!
@fernandocastillo-ke9qv2 ай бұрын
Hola que fresas compro para la fresadora Bosch? Compré por mercado libre fresadora Bosch g 130 Pero no viene con fresa
@Tech-3D2 ай бұрын
Buena relación calidad-precio son los juegos de fresadoras de Bosch: www.bosch-professional.com/gb/en/router-bit-sets-2865252-ocs-ac/ También utilizo fresas de metal duro CMT, sobre todo cuando se trata de maderas duras.
@TheBroomt2 ай бұрын
I have the Bosch GWS 750 and the GDE 115/125, but they don't fit together because the mount is missing. Is it possible to create something with a 3D printer to mount the machine?
@Tech-3D2 ай бұрын
Surely some sort of reduction could be made to connect the cover. It's important how it doesn't fit, what's bigger and what's smaller, etc. Since the angle grinder head can get hot you need to use a temperature resistant material or carbon fiber material.
@TheBroomt2 ай бұрын
@@Tech-3D Thx
@davidokuniewicz40082 ай бұрын
Awesome idea my friend
@MaryamSidq2 ай бұрын
Yours air compressor air is not reaching to the maximum speed but your video is reaching very fast 😂😂😂
@eujnemo3 ай бұрын
Work in 125 volts too?
@Tech-3D3 ай бұрын
A saw with a 230V motor will not work when connected to 125V. The motor will not spin.
@eujnemo3 ай бұрын
@@Tech-3D I ask you kus my Saw , have a motor 125v and i try put One soft startar like yours and do note Work.