No code? and diagram?

Parts name please give it in description

Please city

do not use tp4056 to charge multiple batteries its not safe even for one, ii used it for 2 battries ,board just melted in 10 min i was there so i took it out very fast just think you put it charge went some where for few hours it will catch fire or destroy your battery its get extremaly hot just charging one battery this thing is trash and unsafe

Code??

ok can you tell me how are you able to access the pi without any hdmi cable cinnected ?

❤

does it work with esp32 s3 chip?

How to charge its, give video?

super

Sir ...apne transmitter ka case 3d print kiya hai ?..or Which meturial..you used to make transmitter case..?

what did you use for video stream. wifi or RF?

Sir, how can i buy the small one

2 relay direction control karne ke liye lagaye hai kya juggad hai bhai maja aagya

Wasted 😂

Not a single wire explained.

do we need UART or we can programm it with another ESP32 board ?

What type your battery sir?

do need any resistor to work with this ? can i directly connect sensor with this ?

Thanks for the good instructions 👍

High ampere of laptop charger will cause gradual damage to batteries.You should choose XL4015 or XL4016 to limit current.

Awesome 👌 🎉

Sudheer

Bhai code dedo

Please give me details of the circuit & Diagram

Bro, your circuit diagram connections are different

Can't we use ESP32 at receiver side?

Can I please have the circuit diagram of the drone control and the code link

but what is it, I thought maybe a battery charger. but I guess it's for wireless devices and Bluetooth

so nice

Write the materials

Those who doesn't work the code Take this code it work with this montage #include <LiquidCrystal_I2C.h> LiquidCrystal_I2C lcd(0x27, 16, 2); // Adresse I2C 0x27 (du LCD DIYables), 16 colonnes et 2 lignes int trigPin = A0; // Broche TRIG int echoPin = A1; // Broche ECHO float duration_us, distance_cm; void setup() { lcd.init(); // Initialisation de l'écran LCD lcd.backlight(); // Activation du rétroéclairage pinMode(trigPin, OUTPUT); // Configuration de la broche TRIG en mode sortie pinMode(echoPin, INPUT); // Configuration de la broche ECHO en mode entrée } void loop() { // Génère une impulsion de 10 microsecondes sur la broche TRIG digitalWrite(trigPin, HIGH); delayMicroseconds(10); digitalWrite(trigPin, LOW); // Mesure la durée de l'impulsion depuis la broche ECHO duration_us = pulseIn(echoPin, HIGH); // Calcule la distance en centimètres distance_cm = 0.017 * duration_us; // Affiche la distance sur l'écran LCD lcd.clear(); lcd.setCursor(0, 0); // Début de l'affichage à la première ligne lcd.print("Distance: "); lcd.print(distance_cm); delay(500); // Attente de 500 ms }

Thank you so much! The black 12V version didn't make sense to me with the pads. I didn't know it was 12V by default so got stressed! Thanks sir!

can you make a tutorial on how you build it?

Bro circuit diagram pls

4s battery charge krne ke liye use kr skte h ? Aur buck jyada heat hota h kya laptop charger se charge krne me?

We can heat water using egg boiler...?

Mai bhi ye new liya hu but iron kala padh raha hai plz solution batao bro 🙏

bro ntg is printing on lcd

There is an important piece of code missing in the program under: pinMode(talkButton, INPUT); should be written: digitalWrite(talkButton, HIGH); This way the floating talkButton will be high or low but not floating in between which is causing it to get from receiving to send thousands of times a second. That is what is causing the noise when receiving because it is partially sending as well. With an added digitalWrite(talkButton, HIGH); both sides are muted when no button is pressed. With the button down the program is clearly in sending mode and not echoing. Please repair this in your program because this is disappointing many enthousiasts in electronics which we need dearly in this world.

there is no location called config in rpi zero

How much will it take for omlet?

Kya isme chicken boiled kar sakte hai

thanks, is that 18650 parrarel battery pack, with single bms on it ?

Very good video!!!!

GOOD EXPLANATION SIR

Sir Please Tell Me I Have lithium Cell And I Join Them With Series Now Output Is 12.v So If I Have Laptop Charger Which Dc Output Is 12v 4 Ampere Can I Charge My battery With It

Pls make object pick and place robot using esp32 cam

Digram and code ❓

Good job 👏🏻