Bro thanks for the video. Can we go in visit visa to search jobs, If yes, which city is recommended, I am civil engineer.

Hi ,can i get your email id please ? I want to contact you regarding career guidance

why are u assigning the slave address as 0x12

Hello @EmbeddedworldJoy is there a part 3 of this series, if so do you know when it will be available?

Thank you, Got this "Indiesemic ISC-SX1262-B An advanced LORA module V0.1" and planning build project using arduino Uno and facing some issue to Starting LoRa failed! and unable to find correct number for (!LoRa.begin(868E6)) sketch code, can you please help me

How much salary per month in Indian rupees?

Thanks! literally just started looking for resources for this exact thing

Interested

I m diploma EEE finished sir pls reply Any job opportunities sir

Which company your are working in?

Hi mate im designing a project that 2 stm32 modules communicate eachother with LoRa modules with antenas ofc. My project is basiclly i bought 2 bluetooth modules for my phone to connect stm32. I want to type something from my phone and it will send from Stm32 to LoRa to other LoRa->Stm32-> Phone. And Other phone see my message and response to . Its basicly that. Can you help me by anychance ? These are my equipments ; STM32F407 Discovery Kit 2x EBYTE E22-900T22D V2 model 868 MHz LoRa 2x CDM 868 MHz 915 MHz Antena 3dBi SMA Male Connector - 11CM 2x HC-05 Bluetooth module 2x I bought all of them

Where i can contact you for mock interview??

Hello, i faced some problem in bootloader and user app, i used stm32f429Zi which have 2MB flsh. When i jum from bootloader to user app Hal_delay() ms wont work, means the update event based on systick interrupt just stuck ant the HAL_Delay() stucks at infinite loop. Whsat is possible for such issue.?

Please could you share the link of OLED Display it would be helpful!

THANK YOU

Hi sir I have joined your channel. Is those community projects available in git hub

Hi sir what about the zero to hero course embedded system .. that is enough

How can I find the codes?

Hey guys, can anyone please solve my issue with connecting one esp32 as master and one stm32 as slave with i2c communication

Here is a simpler solution for byte swap. uint32_t byteSwap (uint32_t x) { uint32_t ret = 0; while (x) { ret <<= 8; ret |= (x & 0xFF); x >>= 8; } return ret; }

Intersted

Embedded testing side future scope is there sir

Bro i need help can i get ur Insta id

Sir maine plc and rlc kiya hu diploma electrical passing year 2024 fresar hu please job milega kya

Hi joy Thank you for the video, after numerous videos, i understood the open drain configuration in a very simple way, Thank you for that, can you also add points about Bus capacitance ,and any calculation for pull up resistance values,

Hi bro i have many doubts about embedded domain how to connect with you ?

Sir,in ur void pointer example, i noted that when char type varible address converted to uint_8 ,there was no problem, but when u converetd to int type,there was problem due to the size issue which i understood by ur explanation,but what happens when u convert void ptr to int ptr(instead of uint), there will be the same issue as faced by the int ptr, ryt? Then what is the significance of void ptr?

Interested

Sir you are too good 👍 . And thankyou from bottom of the heart . This content is very useful to freshers.

good tutorial, if possible please share the pdf/notes of your tutorial.

Which company u are working sir?

What is AHB Slave ?

Good Video but my doubt is that at 19:16 you told flash is not very dynamic it's static but flash belongs to DRAM

Interested

Hows the salary

Just a little tip: the microcontoller has more than 1 I2C peripheral, so it is actually possible to an MCU as both master and slave, and use wires to connect the two.

Would like to connect... Please let me know have your comtact...

Tutorial already out?

hii bro, can you make course on embedded c for beginner

Welcome back! Been a while since you posted

How much experience u have in embedded

why cant we use if else

Please do more videos on embedded programming questions

Hi Below is a sample code to swap 2 number much easily without easily hope you will include in next videos #include <stdio.h> int main() { int a = 10, b= 20; printf("Value of A & B Before swap --> %d %d ",a,b); a = b - a + (b = a); printf("Value of A & B After swap --> %d %d ",a,b); return 0; }

Where can i find your linkedin ID? Also, does industry uses cubeMX automated code generation tools or developers program the microcontrollers? For example, to blink a led, we enable a clock first, then configure led, finally write a logic to blink. CubeMX in your tutorials generates automated code which avoids all. Please let me know. Thanks.

Can someone tell me what the mistake in this logic is,.. It doesn't work char* Buff = "File1.c,File2.c,File3.c"; typedef char file[8]; file Names[5]; int i=0,j=0; void file_separator() { while(*Buff != '\0') { while(*Buff != ' , ') { Names[j][i] = *Buff; Buff++; i++; } Buff++; j++; } } int main() { file_separator(); printf("%s",Names[0]); return 0; }

Greak work sir keep continuing

Great explanation

bro explain low layer library

op