How does one measure the amount of torque you bolt in? I am slowly learning how to work on cars
@DeborahDeskins-b2f2 күн бұрын
Moore Timothy Johnson Jeffrey Martin Elizabeth
@bobbytaftfera96022 күн бұрын
Young Michael Walker Barbara Lee Steven
@Lincoln124212 күн бұрын
What about the park sensors??
@robskietventertainment520016 күн бұрын
Is that gonna fit 2020 automatic non turbo hatchback. Thanks
@mordred841217 күн бұрын
Will it fit a 2021 civic sedan?
@Half-a-dime20 күн бұрын
Bro, you’re not gonna zoom in or anything? Just gonna stand 10 ft away from the camera and point?
@elijahcreel170920 күн бұрын
Hello I have a 2013 honda accord Lxs that I believe uses the same parts. Would I still need to cut the shifter case?
@patscott0526 күн бұрын
Just installed this on my 2020 Civic EX Sedan, sounds great! @mattg327 - 1,000 times, THANKS! I went to Harbor Freight as soon as I read your comment. I didn't even use a 10mm socket, just the puller, worked PERFECTLY. It's the only way this should be done IMHO. Thanks again!
@willabunnjr21628 күн бұрын
@procivic what kind of cleaner did you use to clean off the trunk lid and spoiler? I have a 2016 Honda civic that the spoiler got knocked off a few years ago and had been fine but now it’s leaking and want to replace it with something like this. Thanks, William B
@carlosmelendez8317Ай бұрын
Will the 3M tape adhere better if i do this in the direct sun or shade?
@aabhaspanditАй бұрын
Video is for a different spoiler install and you are installing the one that is already installed in the beginning if the video. Not sure what is going on
@HrothgarOdubhghaillАй бұрын
Wish you guys would restock these, been trying to order one for a while now!
@HrothgarOdubhghaillАй бұрын
Mam, and i thought the cowl on my 09 was a pain. At least I didn't need to remove the wiper arms. This is gonna be fun ha.
@gumhoptop8732Ай бұрын
I did this job myself and it took me 2 days to do all 4 corners LMAO. The front struts took 3/4 of the time. I couldn't get the freakin struts separated from the steering knuckle no matter how hard i pressed down on the lower control arm! And yes, I undid the 3 bolts holding the lower control arm to the ball joint. I ended up manhandling those things out of there by compressing the springs and removing the top end of the strut first instead of removing the bottom end of the strut first. I did end up damaging the inner fender liner and panel itself a fair amount... it is not a job I ever want to tackle again unless somebody can magically show me how to remove the struts like butter like how they do in this video.
@OdeBrohamАй бұрын
does it require removing the OEM front lip?
@riley1733Ай бұрын
Thank you very much for this. I bought a Hondata for my Si and disabled the rev hang with it and had to reflash it to stock tonight as I'm thinking of trading it in for a WRX STI. Worked like a charm. Unfortunately, rev hang still drives me nuts. Lol.
@fernandovalderrama1451Ай бұрын
Nice! Now pull the other half 🎉
@luisthen7590Ай бұрын
Is that same shit for me
@Jeff-vh1zzАй бұрын
Hey, thanks for taking the time to make this video. However, once you take the nut off the goddamn wiper arm, you need C4 to get the arm off. Would have been nice to have you cover this part and not waste everyone's time.
@markdahl8082Ай бұрын
Watching a video taken from several feet away while he’s pointing to hidden bolts and sway bars is of little help. Often, the trickiest part of a job is removing and replacing trim……also not shown very well. This is a marginally helpful video for me.
@9thgensi227Ай бұрын
Can I use this for stock suspension?
@Liltwin954Ай бұрын
Hi I have a question
@PeterPutter-f9iАй бұрын
Is that fake leather nor the boot
@francisphillipeck42722 ай бұрын
Worst honda bumper design on any honda model ive ever worked on. What a nightmare. This car looks new and came apart really easily, in 5 years those clips wont come out without cutting them, none of the clips will come out without breaking, the eyebrows will break in half getting them off..... I no longer recommend honda.
@Jeffuxl2 ай бұрын
If anyone struggling to get the studs off the cat use a torch get it red hot and then hammer it off with the extended 10mm socket
@Archers.paradox2 ай бұрын
Be aware this does NOT fit the SI coupe
@Archers.paradox2 ай бұрын
Be aware this isn’t a direct fit for the SI coupe, the plastic trim panel will need to be trimmed
@Jeffuxl2 ай бұрын
Anyone have any tips about getting the welded bolts off the cat cannot get one off
@patscott0526 күн бұрын
Yes, but I can't take credit. @mattg327 suggested a pitman arm puller. I got mine at Harbor Freight for $16. Made that part super simple.
@matthwsperling2 ай бұрын
how tf am i supposed to take out the shifter cables. how are you going to explain how to take off panels with clips but not how to disconnect the shifter cables
@bluecollarnobody42172 ай бұрын
I want an exhaust so bad on my 12 SI, but I do not want it to sound like a fart can so I’m being very picky as to what I put on it
@drydreams85132 ай бұрын
Any idea what length the rear end links need to be to fit in the softer setting on the rear sway bar? I have messed with mine twice shorting them and lengthing them and tilted the bar in every direction possible , I just can’t seen to get them to line up correctly. I have the white line bar and plm adjustable links. They can go longer n shorter than the stock one but I just don’t understand why they are not lining up right the angle is always off. The bar is from u guys but the links are stolen from the local tuner shop in Covina,I didn’t steal them but a local crackhead was selling them in the in n out parking lot brand new in the box sealed who doesn’t own car so they are hot ! He only was asking $25 I couldn’t resist buying them.
@seancombs43602 ай бұрын
i have this BC shifter but there is so much play in the shifter when not in gear. if just sitting in neutral and you push side to side it is playing like there are no gromets or bushings holding it in place. i took it to a shop and they said thats just how it is. any advice? thank you
@rafitaino31372 ай бұрын
wtf!! U didn’t show anything like setting the template drilling etc. Terrible video. Waste of my TIME!!😤😤
@144hashar2 ай бұрын
Hey, can the emblem be placed on a Honda Civic 2013 LX or only on the Si ?
@nikosicapero52942 ай бұрын
I think fits R18 as well?
@anekvasquez99483 ай бұрын
Do you need a tune after installing?
@gavpattАй бұрын
if you have a flashpro then use it
@jmoneyg40753 ай бұрын
My coil overs came in and I never got washers or Allen keys for my coil overs smh
@b864r3 ай бұрын
How’s the build quality on the Sirimoto rear camber control arms?
@Sharnul3 ай бұрын
Would I need adjustable rear upper control arms to perform the alignment on the 9th gen civics or only the front camber bolts?
@rasheedukhan3 ай бұрын
How many miles on this and what were the symptoms?
@mannydgoo3 ай бұрын
Bro i have 43K miles on mine and front passenger already giving me issues, it makes like a cracking noise/thump when i accelerate or hit a small dip. I also have some other issues but nothing major thankfully, these new gen hondas suck ass. They dont build them like before.
@frankfromr92893 ай бұрын
A little late to ask, but I would like to know if it is made of soft plastic material or is it ABS plastic which is harder? Thanks
@orcahang213 ай бұрын
Good 👍 ASS job Brudda ✌.
@frankandersongmail4 ай бұрын
Thank you!!!!! Was able to change out USB cable. 🎉
@godzillabass71374 ай бұрын
Hey bud, I just bought one of these two for my civic, but it came out to be warped or a little bent How do I fix that? Any suggestions? I should recommend on because this is the main thing I always want it for my civic.
@BuciRadisani4 ай бұрын
Hey i have a question, I was trying to change my shifter knob and i accidently dropped a screwninside the hole and i cant see it , but i feel it moving from time to time. Is this dangerous to leave inside or not? Should i take it out right away?
@joseb97194 ай бұрын
Glad I saw this before trying to do it myself 👍 saved me from a headache and making mistakes
@bilbobaggins59624 ай бұрын
dont follow a "mechanic" that does a "how to" video and uses dollar store pliers as a hammer
@Mr.WarwickBot4 ай бұрын
Damn, I’m definitely gunna try and take it out from the front lolol