At the end of the vid the Ai voice talks about magnetism in an activated coil, but the coil that gravity makes the screwdriver fall into is not the one that is being activated....
@ReubenNgomi-b4i9 күн бұрын
Suppose two a resistor is connected in series with the LDR, will they have the same p.d in (I). Presence of light and (Ii) absence of light?
This is a terrible video. Some solenoids have more than 1ohm resistance. The transmission I'm working on now has solenoids that manuals say should read 3.1ohms. Also, they run on 5v, not 12v. So this is wrong with that test also. The correct test for this is to find out the rated current and amp of the solenoid and supply that while monitoring the solenoid. If the voltage or amperage go outside of those preset settings at the beginning, it is a bad solenoid. Most solenoids do test good and only fail when hot and in use for longer periods of time.
@HariAngnaaАй бұрын
Please upload vdo of Samson electro pneumatic positioner calibration.
@pavangoswami7986Ай бұрын
Best payment karne wali Dairy duriyon ki ya dudh ki love u love u love u
@HariAngnaaАй бұрын
Sir Samson electro pneumatic position ka calibration dikha skte hain pleasee 🙏🙏
@HariAngnaaАй бұрын
Sir Samson electro pneumatic position ka calibration ka koi video dal skte hain kya...Samson ka kabhi nhi kiya hamne...please urgent request..if possible today...ya sirf itna bata dijie zero and span kaise adjust krenge
@erickbianeckАй бұрын
WTF, an IA made this shit?
@MrAwyorkАй бұрын
Likely. It even contradicts itself.
@r.klovestory1516Ай бұрын
Prize kitana ka hai
@upwalaankitАй бұрын
Parker wala kaise mangwana hai
@francislopes7741Ай бұрын
Very nice Vedio.
@engineeringconceptsАй бұрын
Many many thanks
@HariAngnaaАй бұрын
Sir mere pas ek Samson ka pid control valve hai iska positioner me kuch problem agyi hai...mere pas teknic make ka positioner hai kya mai use use kr skta hun isme....Mera mtlb kya hum kisi bhi dusri make ka positioner kisi bhi pid Valve me use kr skte h?
@engineeringconceptsАй бұрын
Yes
@HariAngnaaАй бұрын
@@engineeringconcepts we had PID Valve I/p positioner Samson 4763.but it is faulty now. We have a new positioner make Tecnik TVPL 1030 Can I use it?
@engineeringconceptsАй бұрын
@HariAngnaa yes u can use
@HariAngnaaАй бұрын
@@engineeringconcepts line size and make se koi fark nhi padta sir?
@KrishnaKumarrai-c6tАй бұрын
Snf kam bta rahi hai machine kaise sahi karu
@naganagaseshaiah4918Ай бұрын
Contact number pl
@naganagaseshaiah49182 ай бұрын
Pl contact number
@pintujaiswal72792 ай бұрын
Thank you sir
@pintujaiswal72792 ай бұрын
Bahut sundar🎉
@ganagamvrksantosh57252 ай бұрын
Samson control valve positioner unable to set the position of 0-100%. In 100% setpoint it was reaching only 60%, if any adjustment was done 0% was disturbing
@dragonboyy99992 ай бұрын
Big fan bro found your channel at the back of your car in surat!!
@engineeringconcepts2 ай бұрын
Thanks dear
@shivendrakumardwivedi61722 ай бұрын
Thanks sir ji
@engineeringconcepts2 ай бұрын
Welcome
@bhupendrasengar74852 ай бұрын
Transmitter keshe check karte he sir multimeter se
@engineeringconcepts2 ай бұрын
To check the transmitter, you can use a multimeter to measure the voltage and continuity of the circuit.
What is this? An AI voice reading a wikipedia article? Did you actually make anything in this video?
@GopalKumar-oq9oc2 ай бұрын
Essar ka fs 200 kg banna he
@GopalKumar-oq9oc2 ай бұрын
Load seting 200kg
@RamNarayanRajput-fk1vz2 ай бұрын
Very nice.practic.of.working.
@simonkarre77462 ай бұрын
Nice video sir
@engineeringconcepts2 ай бұрын
thanks
@Balaji07official2 ай бұрын
SADC in boiler ke bare mein bataiye SA DC ka pura naam secondary air damper controller
@kuldeeppanchal5382 ай бұрын
Loadcell me resistense okay hai but not ok working please send other type testing loadcell
@DilipKumar-bg7jj2 ай бұрын
Aap ne to off delay mode me check hi nahi kiya ye to on delay conection kiya
@HariAngnaa3 ай бұрын
Sir ek doubt hai...jab I/P converter cheap and easy bhi hota hai phir Positioner.kyu use.krte hain ye to costly and complicated bhi hota hai..? Please clarify the benefit of positioner
@engineeringconcepts3 ай бұрын
Better accuracy and correct results given by the Positioner .positioner give the output feed back but not possible to I/P
@HariAngnaa3 ай бұрын
@@engineeringconcepts jyadatar positioner me to feedback nh hota..jahan tak maine dekha hai.phit b positioner use kr rhe
@andrewhilton43543 ай бұрын
If the solenoid has shorted it needs replacing....if its open it needs replacing...whats a good solenoid then. I thought it was either open or closed??