Works now thank you now just have to find a charging dock somewhere
@wildcat8352 ай бұрын
Hi, Jamie, As soon as I listed the comment, I went and made sure the molex connector that the red, black and red were connects to were make good contact. I unplugged it and pressed it back on real hard because the connector doesn't snap on real good. If it happens again, thing I will solder the yellow and black male pins that the connector slides on together. That will delete that anyway from happening again. Thanks
@wildcat8352 ай бұрын
Hi, I appreciate the video , I cut the yellow and black wire and it work just fine,but the next time I used it the blue light came back on and then went back cutting off and blue light started flashing. I went back and cut the red wire which did not help. I was hoping you might know what else I can do? Thanks
@kishatucker62403 ай бұрын
Worked great, thank you so much.
@biggentallen3 ай бұрын
Thank you so much sir! Im the corded version wires and sensor are accessible from the back in slightly different locations. Was able to confirm the sensor was drenched. Fixed the problem anyhow.
@lisaw23813 ай бұрын
You rock!! It worked,so happy to have my shark back!
@Osharifabuhafs3 ай бұрын
Worked. I took two back to the store every time this happened and got a new one. Same thing happened
@joelreamer94934 ай бұрын
Just tried this and it worked! Thank you! We got shark to send us basically a whole new unit for $15. So it is going to stay in the box now until something else breaks kn this one! Lol
@phillipcervantes22574 ай бұрын
Nice! I wonder if the heat is melting a thread-locker or if the thermal expansion is doing the trick. Nevertheless, this worked. This is the best method I've seen. Thank you, you're a lifesaver!
@Jugo_guero4 ай бұрын
I applied this to a newer purple model and so far so good thanks!
@leewirthwein29175 ай бұрын
THANKS! took about 10 minutes
@josegarrido70215 ай бұрын
great explanation man, i really appreciate it!.
@igorfedin76415 ай бұрын
Much appreciated good sir! 🎩 off to you!
@addaley17026 ай бұрын
Thanks for the video really helpful I follow this video and mine is working good 👍
@cindyeminer6 ай бұрын
Thank you!!! I just fixed my daughter's machine...thanks to u and THIS VIDEO!!!!
@icusawme26 ай бұрын
Got one new out of the box with this error, gonna go get money back... Thanks for the video
@GizmoIII6 ай бұрын
They installed security bolts on the newer model, need to get the girls with the hole in the middle.
@ElanorRiley6 ай бұрын
I was able to use a standard star bit.
@azucenasantana147 ай бұрын
So you only cut black and yellow cables? And connect those two together? What do you do with the red?
@jaimesuarez84976 ай бұрын
Just don't cut it...
@jesusroa32947 ай бұрын
Hola amigo, yo tengo una 3 en 1, WD 101, pero parpadean en rojo el simbolo de agua y alfombra al mismo tiempo, el manual indica que el cepillo giratorio está atascado, ya desarmé y está todo bien, solo gira por 3 segundos y para, sabrás algunas solución? te agradecería bastante, gracias.
@justinfranscique78537 ай бұрын
Thank you very much! I’ve been struggling to get these bolts out
@jaimesuarez84978 ай бұрын
Also check the video on the minute 2:42 and you can see that little hole...
@jaimesuarez84978 ай бұрын
Whit the small screw driver. Look for small hole on the bottom of the handle push in and pull at the same time...!