Can I use the landscape wire 16/2 to hook the light? What is the benefit of using those wire in the video and how does that connect to a transformer?

My wires are white black & gold with like construction lookin paper around it.. help please!!! Of course I know the gold is for the green (ground) but my ceiling fan has again green for ground then white (neutral) blue (light) pink, gray & red for (receiver)

Do you have to use the quad breaker or could you donthis with just a regular double pole? And if so, do you just leave the top and bottom terminals unused?

WORKED LIKE A CHAMP!!!!!! Thanks so much for the tip.

Do you have a video for ceilings originally having separate light and fan switches?

love videos like this

You're meant to cut them in half afterwards so we can see a cross section of how it cooked, otherwise nice vid.

I hate to rain on your parade, but I had a cord reel burn up. It had a breaker in it, but drawing a bunch of current thru it caused it to overheat. Seems that current running thru the wire, coiled up, creates an electrical field that creates heat.

Terry Peterman, You're the best! I just had to subscribe!

good job. I was an electrician and you did it right!

Video really helps but I don't understand how I have power on all 3 switches but lights won't come on

Urdu me tranlete

Great video. My question is, how would you add a light to the circuit you have shown? It appears my house is wired the same as you displayed. I would like to add a light at the bottom of the steps (there is currently only one at the top) Would i need to fish a new romex from the top light to the bottom?

I can't hear bro

This helped me identify the error in my switch wiring. On the secondary 3-way switch which is not directly powered by the circuit, I had the black wire from the traveler hooked into the common screw and the black wire from the circuit hooked in the traveler screw. I reversed those, and problem solved.

Quick question, I have a 170 ft run from barn where I will have a meter base to 30 amp rv pedestal with an additional 20 amp gfci outlet. What size wire do I run the 170 ft to pedestal? and do I run 2 wires? 1 for 30 amp plug and 1 for 20 amp gfci? Thanks in advance

Hi Terry I'm not sure if this is posable but I want to independently turn on and off lights within a 3way circuit. I have an outdoor area with two separate low voltage lights I want to turn it on and off at the house and on and off at the outdoor area but I also want to turn on and off each set of lights separately

Thank you. It helped me changing my pool light .

Saved our day, the first KZbin we opened, and it helped my husband immediately with that red wire!!

Why does ground connect to the box and the back of the plug? Why not just go straight to the plug?

So basically power the receiver, connect the wires from the fan to the receiver by color, tuck away, finish the rest of the job.

THANK YOU!!! I Spent about an hour trying to remove an old box that held the thermostat for old removed electrical base board heaters. I fought with those side brackets thinking they slid up or down to lock the box in place. This video showed me I had to unwrap those 4 tabs!!! This box was attached to Very thin, old 3' x 7' thin wood panels that we plan to replace and paint after installing insulation behind them.

Can't tell you how happy you made me and my granddaughter by providing this video. We struggled trying to figure out how to connect the wires when switching out a ceiling light (my bad I forgot to take a picture before disconnecting the old fixture) as the light would turn on but not shut off with the switch. Now the light works perfectly. THANKS SO MUCH!

They mean electricity

I never knew about the tab split. Than you sooooo much

Do all fans have the hole for the plug in the same spot? Or did I just buy the wrong fan? I wanted to just replace the inside without taking the old case out of the wall…. The plug doesn’t match up though….

Just mark the distance with a piece of tape on the floor, then use a plumb bob to transfer that distance to the ceiling. That receptacle box cutout is not going to be a critical position. Even if it were, you are not going to get it with a tape measure alone. Even just measuring along the floor and standing a narrow beam flashlight on its back end on the floor would probably provide sufficient accuracy. Unless you have a lot of such measurements needing to be made, a laser is overkill.

What do you do when you mixed the two black wires because you didn’t mark them before you install a new switch?

I was looking for how you put inside the ceiling the part to hold the hook, but your video is freezing in the 7 minute😢

What if the terminal screws are one on each side?

FrOm this demonstration u should not be a teacher .. good thing u had the animation to help ..

Why can't you use 2 GFCI receptacles in the kitchen and still use the Load side to feed regular receptacles in the normal fashion downstream? Clearly, you can't split a GFCI, but if you use 2, one powered by the black wire, and the other powered by the red. Create a joint for the neutral wire to connect to each one.

Thank you. very well explained.

Has the NEC been updated to allow luminary 0-10 W wiring to be allowed in a single MC cable along with the other wiring?

Sonos

You know what! It worked.God bless you and may all your dreams come true.

May the swartz be with you😂 dude it worked awsome thank you.

Perfectly...

"What are you doing on the computer, hun?" "I'm watching videos about how a three-way works"

How long will pvc conduit last when exposed to sun ? And will liquid tight last longer than pvc?

Thanks so much for the video!!

Thank you.

The fan is going anticlockwise

Thank you for sharing

Agree, there is always something beautiful about someone who is one with his work, tool and attention to detail. ⚕️🇺🇸

Thankyou

I have a battery operated doorbell, is the installation process still the same? If not, what’s different?

Fu@# Canada and fu@# their municipalities with their permits for petty little jobs like puck lighting. Ridiculous. This is why I will never live or visit there. And Trudeau is a lying son of a bi+(#! I question a population who votes for someone like that. Either really dumb or destructive

Thank you

Immediately beyond a non-electrician. Lots of promises to demystify then … jargon and assumptions. 🤦‍♂️