Hello I have a jiabaida bms a 21s 100a smart bms I needed a 20s so they removed a lead and now that I have it all together it says cell undervolt protection because th missing lead reads as 0 and my battery wont charge or discharge , is there a way I can override this or delete this error code??

Every sink is strange!

Oh dude you just took me back 30+ years, I had 1 very similar or maybe even exactly like that when I was a kid, it was my first radio tape so I remember it well, wish I kept it but alas. Yeah it's stupid that they put in fuses but 95% of the time the fuses survive just fine but the mosfets or chips or other stuff blows up and even fuses to the board and the fuse is still fine 🤦‍♂ You can make an external fuse\current limiter using an incandescent lightbulb in series before the device you're connecting so it won't blow the device or the fuse or the פחת בארון חשמל

This is only welding tool. Electronics sold separately!

I repaired my mouse scrool with watching your video. Thx

Is it not safer to put the bms on the positive side ?

Where is the sensor?

אתה ישראלי נכון ?

👍👍🇬🇧

형. 저렇게 다 분해하지 않고, 똑같은 스위치 사서 덮여있는 금속판 잘 들어올리면 고무 밑에 얇고 볼록한 금속판 있어.. 그거만 교체해 주면 돼. 분해고 뭐고,, 그냥 스위치만 잘 뜯어내면 성공할 수 있어. 납땜이고 뭐고 다 필요 없이 스위치의 금속판만 잘 분해해 봐.

With an RTL-SDR it's actually worth using

I am curious, how does it control the voltage of each cell? Because I didn't notice the regular BMS connected to the battery pack. Maybe these pins on the side of the battery also for the voltage monitoring?

I also had an issue with this powerbank, it just turned into a brick after a few days in use. Unfortunately I didn't have an Anker warranty because I purchased it on a local marketplace (just decided to rely on Anker reputation and quality of their product, my mistake) Many people say that Anker has excellent quality products that work perfectly, but this powerbank is not the case, there are a lot of frustrated customers complaining about this item.

in my case the problem wasn't with the micro switches .. it was with the top plastic cover. it has plastic pins that press the micro switches and over time they "wear down" and become a little bit shorter, but that enough not to be able to press the microswitches any more

It seems you purchased an anchor ⚓️ not an Anker. Sad to see failed cells. It may be worth checking the cell fuse on the 0v cell or termination. If you have access to an internal resistance tester see if it is a short or open.

איזה ערוץ מושלם! במקרה מצאתי אותו.

That’s a great video , needed it but how do I set it up for a phone ?

when i put my iron on (same iron) ,the whole body and tip glows red , how do i fix this ?, is it possible

THANK YOU VERY MUCH!!! Thanks to your video, I was able to bring back to life one I had abandoned and thought was completely dead

Amazing video

Thanks

This video sucks

Thanks - that was helpful.

Does anybody know what purpose does those 2 white plastic serve at the back cover?

Funny how people possibly with little or no skill complain Why not put up your own videos??? I am in the throes of dismantling one that has sat for a couple of years and started to dismantle and found your video very helpful thanks To the complainers Check for video’s on how follow electrical circuits and soldering off ya go I have now got mine apart and I don’t think they are designed to be repaired

I bought it n it's waste manzee ....

very good video to show the parts and components. Thank you

I have to have this. Is this what I know if the battery is dead?

How many volts do you give to each output?

This helped a lot. Thank you sir

Why do you need it? Usually the precise torque is needed for nuts and bolts, it's rare to see specific torque needed for screws.

Does anybody know what exactly is defect on motor ? Thx

This FM bug is crap because it actually transmits in the 50 Mhz range and what is being picked up in the 88 to 108 Mhz FM band is a second harmonic so unless you have a radio receiver that can receive in the 50 Mhz band you will not get much range.

If anyone else has problems with the left button only working when pressed really hard... Over the plastic stick you can applied a little glue (transparent plastic like) and ualá!

What do you think of it? Is it accurate in measurements?

❤❤❤

i took apart my mouse and cleaned the wheel & sensor but still scrolling doesnt work. could it be an issue with the sensor itself?

I'm doing the same thing with the same kit and even same spot welder!

Thank you very much, Sir! Your video is very important!

lol sorry to disappoint you buddy but anker was good many years ago when no one knew about them, now most of their budget goes to advertising so the high price is for too much advertising and not enough for R&D just like samsung and apple, that's why I stopped buying their overpriced crap years ago.

😅 like that glove will protect your hand?….

como se conecta a la corriente de luz?

Put your hand over the intake and will always pulse as it thinks it's blocked. What a waste of time watching this.

It's an interesting comparaison , thank you

have the same and my battery always drop to 1 V, i bought new one but who knows

My mother used to say and kept repeating herself: You have the most incurable decease called Blochitis. Never really understood it, we used to dislike more than half the food available but when it comes to patience or the stubborn will to fix everything I finally do understand.....

My scroll wheel wasn't working. Using your instructions I opened up the top cover and cleared out some fluff at the front of the scroll wheel. The scroll wheel is working perfectly now! Thank you! I found it easier to open up the top cover from the rear, opposite side of the mouse buttons.

I’m needing to change electric box and told I need to remove pump but unable to unscrew the 4 screws on pump. So t move at all any tips appreciated

It is a bad design thanks for the video tough but I think I gonna settle for an other brand.

תודה!