Is windows XP required ? where can I download the program you use
@electricaltechie3 күн бұрын
CAP505 software. XP not necessary
@RahulKumar-sw2hk9 күн бұрын
Sir, when I communicate the relay shows this message "the order code and version will be reset".
@KH4UF14 күн бұрын
Gaana baja ne ke bajaye 2 line kuch bol bhi diye hote
@electricaltechie14 күн бұрын
@@KH4UF bilkul. Bearings ka ek detailed video mein bataunga. This is just to see how different models of ball bearings look like.
@KH4UF13 күн бұрын
@@electricaltechie where do you work at
@shyamalsarakar252816 күн бұрын
Sir fault code pf ayatoh kya check karna hai
@electricaltechie16 күн бұрын
Phase Loss
@danishqureshi771118 күн бұрын
what is the password of relay configuration tool? is it same for all?
@electricaltechie18 күн бұрын
Password is either: *****1 or *****2 or ******3. Only the last digit to be changed in password.
@tuntunpichi18 күн бұрын
Thank you
@electricalmotorsanddrives720620 күн бұрын
How to change 46-2 parameter its not changing i want to increase delay time
@electricaltechie18 күн бұрын
To be done in Group-2 settings of 46-2. Why it's not changing ?
@parisbond428626 күн бұрын
Output contact PO1or SO1make it latch contact plz
@ImranKhan-nu6xw28 күн бұрын
Great job thanks
@skisrafil271Ай бұрын
plz guide sir for Digsi 4 Full configure and goose for any relay
@electricaltechieАй бұрын
kzbin.info/www/bejne/hKvLn4Sco9lmopI. Refer this for Goose
@kaderhouari86Ай бұрын
Thanks for the wonderful videos I coming to you asking you for a solution My issue is when I have an any a detection fault on the REF 630 I can't lance any commands from the SCADA driving center except in an the case where an employee come into the substation and proceed to default acknowledgement In front of the relays REF 630 so in conclusion I want to tell you now in my relays there is a condition to make a maneuvre (close circuit breaker ) from the driving center the condition is acknowledgement default if you have a solution for this kind of issue I will be thankful for you to tell me
@QurriChАй бұрын
@electrical techie How to connect with relay ref54x with rs-232 serial ports? Do u have scheme communication rs-232?
@electricaltechieАй бұрын
Through MOXA serial to USB cable
@excellentthinks8656Ай бұрын
Sir is relay ka disturbance record kaise nikale
@ELECTRORACSOАй бұрын
HOW CAN I GET THE PROGRAM? plsssssss
@rudehelper1122Ай бұрын
Kon se equipment se ye test karte hai
@electricaltechieАй бұрын
@@rudehelper1122 inject current in Motor RYB phase & check neutral current in relay
@sunilkumar-md7rjАй бұрын
Please hindi language me bhi video banaiye
@lokanathpanigrahi3208Ай бұрын
Sir please make video regarding generetor relay protection testing.
@crazyheadphones11712 ай бұрын
Hello Sir, I performed the same test but faced some issues . I would be grateful if you could help in resolving the same. I applied 3 phase supply using a variac in the primary of the supply. I connected in zone busbar one phase to the ground. When I started increasing the voltage from the variac, the current in ground conductor shows zero when measured with the clamp meter. The panel is connected with grid system earthing which has value less than 1. Please suggest to troubleshoot the issue
@electricaltechie2 ай бұрын
@@crazyheadphones1171 what is the connection type of transformer & voltage rating. How much voltage did u apply with variac ? Which phase did u ground in in-zone fault ?
@crazyheadphones11712 ай бұрын
The transformer primary is Delta while secondary is star connection. Voltage rating is 11kv/0.433V, 2.5 MVA. From variac the supply given was approx 50-60V. Red phase was grounded in inzone . The variac was of 3 phase. The earth was grid type where 50 earth pits are connected parallel using earth flat
@electricaltechie2 ай бұрын
@@crazyheadphones1171 I am asking the vector group of Transformer - Dyn1 or Dyn11 ??
@crazyheadphones11712 ай бұрын
Dyn11
@omprakashtiwari94922 ай бұрын
First you should clear your self then upload the video
@electricaltechie2 ай бұрын
@@omprakashtiwari9492 I only make videos for the topics which are not clear to me.
@agriculturefarming59222 ай бұрын
except the vedio quality the explanation and content is very nice as a direct approach to configuration without moving aroud the bushes and wasting time.thumbs up for u
@electricaltechie2 ай бұрын
@@agriculturefarming5922 thanks for ur support 🙏
@RahulKumar-sw2hk2 ай бұрын
Micom relay function key configuration ? Please
@rakeshverma-cu8ug3 ай бұрын
I need your help to make Psl congratulations for ht , will pay for making me able to Psl skilled
@rakeshverma-cu8ug3 ай бұрын
I need your help to make Psl congratulations for ht , will pay for making me able to Psl skilled
@rakeshverma-cu8ug3 ай бұрын
I need your help to make Psl congratulations for ht , will pay for making me able to Psl skilled
@hamidusman30794 ай бұрын
Sir how to change CT RATIO SETTING IN REF542 PLUS. PLEASE guide
@RahulKumar-sw2hk4 ай бұрын
I have REM615 RELAY but DR & Events not showing in Relay.
@Arab_Developers_Academy4 ай бұрын
Hi sir ihave siprotec 4 7sj6225 ihave the power supply 24 to 48 v dc now i run on 48v dc but the in the digsi say binary input preset 19v dc so the control input voltage must be 19v or ican use 24 or 48 vdc without problem thhnak you
@electricianguruji2.05 ай бұрын
Mujhe starting se sikhna hai kya karu?
@electricaltechie5 ай бұрын
kzbin.info/www/bejne/bZiqoWehjbidhK8. Pl refer this video
@ImranKhan-nu6xw5 ай бұрын
Ye Kaisi vedio banai ha poore vedio apko khud communication ka pata nahee Chala
@electricaltechie5 ай бұрын
Mein usi chiz ka video banata hun jo mujhe khud samaj nahi aata hai 🤣🤣
@mohanrajk65175 ай бұрын
Bro really excellent 🎉
@mathiarun84533 ай бұрын
how to download SIGRA software
@lokanathpanigrahi32086 ай бұрын
Please make a video from starting ,how to add template , configuration and testing. And make a video about Ray role relays.
@lokanathpanigrahi32086 ай бұрын
🙏
@prabhatsingh53776 ай бұрын
What is the use of virtual input and output?
@tanzeemkhan857 ай бұрын
Appreciate it!!!
@UmeshSingh-jw1je7 ай бұрын
Nicely presented and informative
@kishorek3377 ай бұрын
Please share the PDF file shown at timeline 0.14, 0.50 & 1.10
@GalaxyA21s-wr7oi7 ай бұрын
Main bhi winder hoon badi motor ka kaam kartahoon chan bloke aur ghore se Sara kaam asani se ho jata hai
@GalaxyA21s-wr7oi7 ай бұрын
Mere bhai agar aap ke pass badi motor ka kaam hota hai toh aap ek ghora bana leny aur niche pahiya laga leny chan bloke se rotor nekale
@electricaltechie7 ай бұрын
Dhanyawad 👍
@prabhatsingh53777 ай бұрын
Kindly make a separate video pls🙏
@prabhatsingh53777 ай бұрын
Too much noise and pictures also not clear
@electricaltechie7 ай бұрын
High resolution video is rendering. Pl wait for 90 mins
@prabhatsingh53777 ай бұрын
@@electricaltechie thanx . Very helpful 😊
@electricaltechie7 ай бұрын
High resolution video available. Please bear with the noise.
@RahulKumar-sw2hk7 ай бұрын
Thank 😊
@christiancarvajal5247 ай бұрын
Password please: 3 digit!, 1 digit is invalid password
@electricaltechie7 ай бұрын
Last digit is *****1 or *****2 or ******3
@vyshaghnk98778 ай бұрын
How should I time sync the relay with my server
@electricaltechie7 ай бұрын
I will make a video soon
@vyshaghnk98778 ай бұрын
How should I time sync the relay with my server
@herwinjanuardi71138 ай бұрын
What the application to open format .dex ? Omicron .??
@electricaltechie8 ай бұрын
DIGSI 4.93
@AhmedDarraji8 ай бұрын
Is it possible to service it? I have the same device and the screen has become white or snowy. How do I return it to normal?
@electricaltechie8 ай бұрын
Connect with laptop & check all the parameters and logics. If it's working fine then change the display only.
@AhmedDarraji8 ай бұрын
@@electricaltechie Thank you for replying. Can you make a video showing removing the snowy image from the relay screen?
@meghnadshyamal21348 ай бұрын
Is this a guide or a gossip?
@electricaltechie8 ай бұрын
Guide via gossip
@ErRajat3 ай бұрын
😂
@delosmark188 ай бұрын
do you have copy of the software for this specific relay model version? or does the enervista 650 ver. 8.51 will work?