Thank you so much for this amazing professional video.🎉

don't stack your receivers and antennas like that, use a mic combiner

I have an issue where the frequency and all of that is connected and I’m getting levels coming out on my sound board, but the light is red and so I’m not getting sound. The mic isn’t muted nor is the battery low. I just can’t figure out how to get the light to be green (or live) I’m not sure if it’s a settings issue or not

Just run wireless workbench. It’s free

Thank for video - I have shure ulxd1 and users saying audio cutting in and out randomnly. I will try your fix and see? -your hand was in way and couldn’t see display.. I take it menu button is to change both channel and group?

you can always increase the transmitter power from 1mw to 10 mw to get a stronger signal and do an auto scan

Thanks for the information! This was driving me nuts!

Thank you

I have 4 of these units and more then 90 percent of the time when I turn on the receiver I’m getting blinking rf and it doesn’t matter where I am . I’ve tried your method of scanning and sometimes I’m having to scan 30 times before the rf signal will Go away is there any easier way or should I just buy a better unit then the qlxd

Very Helpful! Thanks.

Yes, all i do is change channel and find the right frequency.

Having your antennas like that could be the cause of your cutting out

someone pls buy this guy a big mac. thanks man

Great stuff!

interesting. so much we don't know about wireless mics

I been looking for this answer long time ago! THANK YOU VERY MUCH for sharing....

what about BLX lower versions? Any methods to see the RF signal?

Thank you

Hi. i own a Qlxd4. After installing the 2.4.7 firmware i get in the Rx a message: Fail Err001. What can i do? Thanks.

Perhaps a fancier make/model would do the frequency selection on the fly for you. More costly, yes. More transmit power wanted, yes.

Thank you for sharing.

erro 007&009

Thank you for this tips

Tnk u so much sir, legit

Really useful information. It resolved my issue. Thanks 🙏🏻.

Thankyou Microphone drop out

Good info....

Thank you! I’m dealing with this issue at my church currently. This is likely the issue.

Hi there, I's like to seek your permission to use this video to show my students as I am teaching them on RF coordination. Thanks for the video!

Such a simple idea for a nagging problem we’ve been having. Why didn’t I think of this sooner? Thanks.

I have a Sennheiser mic doing the same thing. The indicator flickers at a high speed at times. I've changed frequency two times and the problem comes back. There is a electric piano between the transmitter and receiver. Could the piano be causing this problem?

Perfect, problem solved! You were so much help, thank you.

Auto scan and war game , is the proper process without doing a full coordination of the venue. Randomly setting frequencies is a road to intermod distortion between the transmitters when you introduce a second, third, fourth etc...signal . I would be careful using this method. No hate just facts.

I can't wait to try these tips. So great that you shared. Thanks.

🙌🏼 Master!

Thank you for the information. It was very helpful for me when I was installing new microphones and had frequency issues.

Good troubleshooting methodology, but these systems can do this process automatically and in a few seconds. There's no need to do it manually! You could spend 10 minutes doing this manually when the device itself can do it in 10 seconds (including automatically syncing the frequency to the transmitter). This unit retails for $1200 for several reasons, one of which is ease of use...please don't waste time doing this process by hand!

Thanks great video.

ok I'll let you know if it works

Why not us WWB6 software to find frequency or let the receiver auto scan a clear group and band. Also do you try to find out where was the un-welcome signal came from. I assigned to each room and congregation to have their own group and channel to away from others.

O Will try this on the stage today

great explaination of the issue , thanks Michael,

thanks for the advise. appreciate it.

Thank you so much! We were having radio interference on a live broadcast and I couldn't figure out how to eliminate the interference but now the signal is clean and I have no bars in my RF indicator while the bodypack is turned off! Thanks again!

As someone who want to be a stage hypnotist I would like to use a lavaliere mic for my speaking while at the same time handing the people on stage a hand held wireless mic. Can anyone tell me which body pack and receiver I should get, make and model. I notice shure makes diff body packs, so any suggestions? [email protected] THANKS!!!

Frequency scan works without the guesswork. I’d still say to watch the rf meter for any action. Additionally, keep mics in the same groups because different groups may actually slightly overlap other group frequencies. Last thing, with the recent wireless repack from the FCC, the available frequencies are getting jammed up especially in dense metro areas. You may want to consider learning how to use an antenna distro and some directional antennas. These will help focus your receivers towards the spaces your mics are coming from and not be catching 360 degrees around you.

Great info. THX

thank You.. Excellent help

Why don't you just use the auto scan feature?

Thank you.